PHILIPS BPP614 Urban Lamp Post Instruction Manual
- June 8, 2024
- Philips
Table of Contents
PHILIPS BPP614 Urban Lamp Post
Stela Square/Wide
BPP612/BPP614
System Power depends on amount of LEDs: see product label.
Ambient: -20 to+ 35°C in general. Specific max ambient temperature see
product label. If nothing stated on product label max ambient temperature
25°C. Other ambient temperature on request.
Exception for certain versions equipped with dimming gear, mini photocell:
please check the gear label.
This luminaire
must be installed only by qualified personnel
Disconnect before servicing
583 – 443000020845 L
2021-08-20
© SignifyHolding All rights reserved
* 10kV for L/N –
GND non-conductive connection
TYPES OF MAIN CONNECTOR
Safety instructions
For skilled electricians and trained personnel in accordance with national legislation, including the relevant standards. Observe the national safety rules and regulations for prevention of accidents and the following safety instructions.
- The technical data on product label indicated on the light fitting and the gear are to be observed.
- Changes of the design and modification to the light fitting are not permitted.
- The light fitting shall be operated as intended and in undamaged and perfect condition.
- Only genuine spare parts may be used for replacement.
- Repairs may only be carried out by a qualified “electrician”.
- Do not keep these operating instructions inside the light fitting during operation.
Conformity with standards
- This light fitting meets the requirements of EN 60 598.
- It has been designed, manufactured and tested as a state of art product and according to EN ISO 9001-2000 quality management system.
- It meets CE requirements.
Technical data
Technical details are stated on the product label. This label states number of LEDs, system wattage, supply voltage and frequency, power factor /cos phi, maximal current, electrical insulation class ( if class 2, double insulated), maximum ambient temperature ( if nothing is stated the maximum ambient temperature is 25 degrees C ), IP value , CE mark.
Installation
Observe the respective national regulations as well as the general rules of
engineering which apply to the installation and operation of electrical
apparatus.
Transport and storage of the luminaire is permitted in original packaging and
specified position only. Installation instructions are included in the
packaging of each luminaire and are to be strictly followed.
We advise to disconnect the lantern from the power supply before gear exchange.
Taking into operation
Prior to operation, check the light fitting for its proper functioning and installation in compliance with these operation instructions, the installation instructions and other applicable regulations.
Maintenance, servicing and repair
When servicing, in particular those components that affect the type of protection, will have to be checked and replaced if applicable, e.g. Disconnect the lantern from the power supply before opening it or carrying out repairs!
Observe the national regulations applicable to the maintenance, servicing and testing of electrical apparatus as well as the general rules of engineering.
- Depending on environmental circumstances the luminaire may need to be cleaned. For cleaning only use a damp cloth or sponge. Only use customary household wash-up liquid diluted in water. After cleaning rinse with clear water.
- In case of driver failure, 100% LEDs out, the luminaire can be opened for replacement of this driver.
- Check gaskets of the driver housing for their perfect condition. Grease the gasket with acid-free grease.
- Check terminal blocks for their firm fit.
- Only use genu infidel spare parts.
- The LEDs and lenses can not be replaced on site. The IP66 LED/lens compartment may not be opened in order to safeguard the proper light technical, electrical and mechanical working of the luminaire.
Installation instructions
Installation instructions are included in the packaging of each luminaire and are to be strictly followed.
Have you already downloaded the
Philips Service tag app?
It helps you make LED maintenance easier and faster!
-
Download the app
-
Place tag on the fuse box
-
Register the product
And also…
Mounting instructions
Troubleshooting
Spare parts
list
Driver re-programming
Want to know more about Service tag?
Go to www.philips.com/servicetag
Annex I: Simplified EU Declaration of Conformity
Hereby, Signify Holding declares that the radio equipment type included into
the luminary is in compliance with Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address:
http://www.philips.com/lighting
Signify Holding
Hereby, declares that the radio equipment type is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following internet address: http://www.philips.com/lighting
SR compatibility – For SR-based luminaires only SR-Certified
components/sensors are to be used (see also:
http://www.lighting.philips.co.uk/oem
EMEA/products/driving-connected-lighting). The functional compatibility of two
(SR-certified) components/sensors to be used in combination, as well as the
override possibility of any line-switch function used in an SR-based
luminaire, is to be released by the master component/sensor supplier. If using
a NEMA 7-pin socket on an SR-based luminaire, a full system verification is
required. Not following this advice can/will cause risk of damage and non-
compliance for which Signify cannot take any responsibility.
Disconnect before servicing
Luminaire has basic insulation between Low Voltage supply and control
conductors.
The control gear and/or the external flexible cable contained in this RO luminaire shalt only be replaced by the manufacturer or his service agent or a similar qualified person. The light source contained in this luminaire is not replaceable, in case of damage replace the luminaire.
2021 Signify Holding.
All rights reserved. This document contains information relating to the
product portfolio of Signify which information may be subject to change. No
representation or warranty as to the accuracy or completeness of the
information included herein is given and any liability for any action in
reliance thereon is disclaimed. The information presented in this document is
not intended as any commercial offer and does not form part of any quotation
or contract. Philips and the Philips Shield Emblem are registered trademarks
of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding
or their respective owners.
Signify Holding.
The Netherlands
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>