legrand WNAH1 Adorne Smart Gateway Instruction Manual

adorne™
WNAH1 Smart Gateway with Netatmo
No: 341344 – 08/21 Catalog Number(s)
WNAH1
Wall plate sold separately

Installation Instructions

Country of Origin : Made in China
For more information and helpful how-to videos, visit www.adornemyhome.com/install.

REGULATORY INFORMATION

FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 90mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.
Contains FCC ID: 2AU5D-WNRH1
IC NOTICE: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 90 mm to the human body.
Note: Any changes or modifications to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment.
IC ID: 25764-WNRH1
HVIN: WNAH1
INSTALLATION INSTRUCTIONS
Please read these instructions completely before you begin. This adorne™ device is designed for installation in standard electrical boxes. However, some of the installation methods vary slightly from traditional methods. If you do not understand these instructions or are unsure of your abilities, seek the assistance of a qualified electrician.
Use only with Legrand adorne™ system.
WARNING
To prevent severe shock or electrocution, always disconnect power at the service panel before beginning work.
When replacing existing device, label wires before disconnecting. Disconnect old device. Choose a place to install the Gateway
If there is an Internet router in the home, use a smartphone to check if the WiFi signal is strong enough in the chosen place.
If there isn’t a router yet, choose a place near a fiber or Ethernet port which will be used for the router.
This device is compatible with standard U.S. electrical boxes, attach with screws.
If necessary, cut wires and strip insulation using stripping guide on back of gateway. WARNING
Failure to connect the ground wire will result in an unsafe installation that could lead to personal injury.
Connect frame ground wire to bare ground wire in box. Fold ground wires into back of box. Mount frame to wall box with screws provided. Tighten screws just enough to hold frame in place. Do NOT over-tighten. TIPS

• Pre-fold wires into wall box to make it easier to fit them in the box when gateway is connected.
• Use caution to avoid marring wall surface with the metal frame.

Connect new smart gateway as shown. Make sure the terminal holes are clear. Insert wires into terminals and torque terminal screws to 14-16 inchpounds. Do NOT over-tighten. NOTE – If you are installing multiple devices in the frame, wire all devices before snapping them into the frame.

• Connect the WHITE neutral wire(s) in the box to the “WHITE” terminal on the gateway.
• Connect the HOT wire(s) in th box to the “HOT” terminal on the Gateway.

**WARNING: Do not pair different size wires in the same terminal. If you have different size wires, use a wire nut to add a 6 inch pigtail of the same gauge wire to the smaller gauge wire.
Carefully fold wires into box.
Snap gateway into frame.TIP – Since the frame completes the enclosure, it’s safe to power up the gateway and test. Allow one minute for the electronics to charge after installation. NOTE:** –If you need to remove gateway after snapping into frame, first remove power from the circuit, then remove the frame from the wall box to access the three locking tabs on the back of the device. Insert a flat screwdriver to depress tabs as you apply pressure to push device out.

Setup the gateway

NOTE: See getting to know your Gateway section for feature details. Turn the power back on at the circuit breaker. To confirm power is on, the LED on the Gateway should be solid magenta for 5 seconds. Follow the instructions from the app to finish setting up your system.
TROUBLESHOOTING TIP: If the device is not powering check wiring to determine if you have reversed the “HOT” and “LOAD” wiring.

Getting to Know Your Gateway

Use a paper clip to access

Reset to Factory Default
Deleting a device from the app will reset it to factory defaults. To manually reset the device to factory defaults, press and hold the EZ button for 20 seconds untill you see the LED turn solid orange, then release. After the LED turns magenta for 5 seconds and turns off, follow the instructions from the app to finish setting up your system.
Legrand reserves the right to change specifications without notice.

LED Indicator Light Explanation

reset
Gateway receives an update| Flashes blue for 2-3 minutes| Gateway is updating

Due to ongoing product improvements, Legrand reserves the right to change specifications without notice. For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: https://www.legrand.us/p/wnah1w1

https://www.legrand.us/p/wnrh1wh

Set up your System

a. Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.
b. Connect your smart device to your home network by following the step by step instructions in the app.
c. Use the app to control your smart device.

Snap wall plate to frame.

There are three click-stops to adjust the fit of the wall plate to the device and the wall. NOTE: To remove wall plate, insert a small, flat screwdriver in notches on wall plate and twist gently to pry from frame.Never apply cleaner directly to the device or wall plate. Apply to a soft cloth and use cloth to remove any smudges from the product.

Technical Assistance:
877-295-3472
www.adornemyhome.com/install
LIMITED TWO-YEAR WARRANTY
Limited two-year warranty information for adorne products is available at www.legrand.us/adorne/warranty. Limited warranty information for adorne™ products may also be obtained free of charge by sending a written request, along with your proof of purchase (including purchase date), to:
Legrand
Attn: adorne Customer Service/Warranty Department
50 Boyd Avenue
Syracuse, NY 13209

© Copyright 2021 Legrand All Rights Reserved.
60 Woodlawn Street
West Hartford, CT 06110
1.877.BY.LEGRAND
(295.3472)
www.legrand.us
CANADA
905.738.9195
www.legrand.ca

References

• Search Results Page
• Legrand US | Delivering and Managing Power, Light, and Data
• The adorne® Collection | Legrand
• adorne® Warranty ⎸Legrand
• adorne® Smart Gateway with Netatmo, White | Designer Switches and Outlets | Wiring Devices

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>