legrand WNRH2 radiant Surface Mount Smart Gateway Instruction Manual

June 8, 2024
Legrand

legrand WNRH2 radiant Surface Mount Smart Gateway

radiant® WNRH2 Surface Mount Smart Gateway with Netatmo

Catalog Number(s)
Country of Origin:
Made in China

REGULATORY INFORMATION

FCC NOTICE: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna
  • Increase the separation between the equipment and receiver
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
  • Consult the dealer or an experienced radio/TV technician for help This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 90 mm between the transmitter’s radiating structure(s) and the body of the user or nearby persons.
NOTE: Any changes or modifications to this device that are not expressly approved by the manufacturer will void the warranty and the user’s authority to operate the equipment.
Contains FCC ID: 2AU5D-WNRH1
IC NOTICE: This device complies with Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions:
(1) this device may not cause interference; and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

RF EXPOSURE STATEMENT: This equipment meets the SAR evaluation limits given in RSS-102 Issue 5 requirements at the minimum separation distance of 90 mm to the human body. Note: Any changes or modifi cations to this device that are not expressly approved by the manufacturer, will void the warranty and the user’s authority to operate the equipment. IC: 25764-WNRH1
HVIN: WNRH2

BEFORE YOU START

Review this guide in its entirety. Consult an electrician with any questions or if you are unsure of your abilities.
Warning: Incorrect installation could result in death, serious injury, and/or damage to your home or devices.
Caution: To reduce the risk of injury and/or overheating and damage to other equipment:

  • For dry, indoor use only.
  • Do not use to power medical equipment – not suitable as a disconnecting means.
  • Do not use with loads exceeding the device load rating.
  • Connect the Gateway to a 120 VAC, 60 Hz power source ONLY.
  • Always use copper wire to install the Gateway and follow all applicable local & national electrical codes.

WHAT YOU NEED

Required:

  • Phillips-head screwdriver
  • Flat blade screwdriver You May Also Need:

Voltage tester, pliers, wire cutter, wire stripper, electrical tape, flashlight, wiring leads (included), and wire nuts (included).

INSTALLATION & SETUP

  1. Choose a place to install the Gateway

    • a) If there is an Internet router in the home, use a smartphone to check if the WiFi signal is strong enough in the chosen place.
    • b) If there isn’t a router yet, choose a place near a fiber or Cat 5 socket which will be used for the router.
    • c) This device is compatible with standard two gang U.S. electrical boxes, attach with screws, or it may also be installed over the wall, next to a one gang standard electrical box. The Gateway can be installed next to any UL listed device in the home.legrand-WNRH2-radiant-Surface-Mount-Smart-Gateway-FIG-1
  2. Turn off power to the box at circuit breaker NOTE: Ensure power is off to all devices in the electrical box.

  3. Remove existing device Check for the following wires:

    • a) HOT or LINE: Receives power from the circuit box. Referred to as “HOT” for the purpose of this guide. Do not touch or let “HOT” wire contact other wires.
    • b) LOAD: Directs power to your load (light or outlet).
    • c) NEUTRAL: Creates a path to return current to the power source when thedevice is off. Required for your Gateway installation.
    • d) GROUND: Provides a safe path for electricity in the event of a short circuit.
  4. Attaching your device to the Smart Gateway
    Use the wire nuts provided to secure the wires together.

    • a) Connect the white NEUTRAL wire on the Gateway to the neutral wires(s) in the box and to the white NEUTRAL wire on your device using the red wire nut.
    • b) Connect the black HOT wire on the Gateway to the HOT wire(s) in the box and to the black HOT wire on your device using the red wire nut.
    • c) Connect the GROUND wire(s) in the box to the GROUND wire on your device.
  5. Attaching your device to the Smart Gateway
    Attach the Gateway to the device paired next to it using the #6-32 x ¼” screws supplied. Orient the Gateway to the left or right of the paired device as desired.legrand-WNRH2-radiant-Surface-Mount-Smart-Gateway-
FIG-2

  6. Wiring
    Follow wiring instruction for mating device along with this instruction sheet.

    • a) Connect the Hot Wire to the Black wire of the Gateway (follow instructions for mating device Hot connection).
    • b) Connect the White wire of the Gateway to the Neutral wire in the box (follow instructions for mating device Neutral connection).legrand-WNRH2-radiant-Surface-Mount-Smart-Gateway-FIG-3
    • c) Connect the ground wire in the box to the ground connection on mating device.
  7. Secure Gateway

    • a) Fold the wires into the electrical box, taking care not to pinch a wire.
    • b) Use mounting screws to secure your device to electrical box with the Gateway hanging over the wall,
    • c) If further attachment is desired (not required), use either drywall screws to attach to stud if present, or use drywall anchors provided (may need to remove screws from step 5.b after marking location for drill hole). If mounted over tile or marble, the provided adhesive strip may be used instead.
  8. Set up the Gateway
    NOTE: See getting to know your Gateway section for feature details.
    Turn the power back on at the circuit breaker. To confirm power is on, the LED on the Gateway should be solid magenta for 5 seconds.
    After initializing, the LED will blink green to indicate setup mode. Follow the instructions from the app to finish setting up your system.

  9. Set up your System

    • a) Download and launch the Legrand Home + Control app. The app is available on the App Store or on Google Play.
    • b) Connect your smart device to your home network by following the step by step instructions in the app.
    • c) Use the app to control your smart device. For the most recent instruction sheets or more information on this product, please see this link or scan the QR code: https://www.legrand.us/p/wnrh2wh

GETTING TO KNOW YOUR GATEWAY

Item Name Description
1 LED

Indicator Light

| Indicates the current state of device during setup.
2| EZ Button| Used to initiate setup.

LED Indicator Light Explanation

Action LED Gateway Behavior
Power to the Gateway Magenta for 5 seconds Gateway booting up
After Gateway boot up Flashes green for 15

minutes

| Setup mode: refer to app
Press EZ Button for 20 seconds| Solid orange| Factory reset
Gateway receives an update| Flashes blue for 2–3 minutes| Gateway is updating

Reset To Factory Default

  • Deleting a device from the app will reset it to factory defaults.
  • To manually reset the device to factory defaults press and hold the EZ button for 20 seconds until you see the LED turn solid orange, then release. When the LED blinks green, follow the instructions from the app to finish setting up your system. Legrand reserves the right to change specifications without notice.

For covering patents, see www.legrand.us/patents
No: 341342 5/21
© Copyright 2021 Legrand All Rights Reserved.

Questions? We’re here to help.
Phone: 1-877-833-3303 8:00 a.m. to 8:00 p.m. EST (M-F) Email: smartlighting@legrand.us
Chat: https://www.legrand.us/radiant/smart- lighting.aspx
(Click on the chat icon to open a dialogue box)
800.223.4185 1.877.BY.LEGRAND www.legrand.us www.legrand.ca

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals