Harbor Breeze WLM141MBK Oakdale 1-Light 10.25-in Black Dark Sky Outdoor Wall Light Instruction Manual
- June 8, 2024
- Harbor Breeze
Table of Contents
Harbor Breeze WLM141MBK Oakdale 1-Light 10.25-in Black Dark Sky Outdoor
Wall Light
PACKAGE CONTENTS
#4145| 52
ITY
| #4145453
QUANTITY
| #4145470
QUANTITY
---|---|---|---
PART| DESCRIPTION| QUAN
A| Fixture| 1| 1| 1
B| Mounting Strap| 1| 1| 1
C| Decorative Nut
(preassembled to mounting strap (B))
| 1| 1| 1
D| Socket Ring
(preassembled to fixture (A))
| 1| 1| 0
E| Screw
(preassembled to fixture (A))
| 0| 0| 3
F| Shade| 1| 1| 1
HARDWARE CONTENTS
(shown actual size)
SAFETY INFORMATION
READ AND SAVE THESE INSTRUCTIONS
DANGER
- For your protection and safety, carefully read and understand the information provided in this manual completely before attempting to assemble, install or operate this product. Failure to do so could lead to electrical shock, fire or other injuries that could be hazardous or even fatal.
- If using this light fixture in a WET location, this light fixture must be connected to a supply circuit that is protected by a Ground Fault Circuit Interrupter (GFCI) to reduce the risk of personal injury, electrical shock or death.
- DO NOT connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use a fixture in a two-wire system that is not grounded. Installing a fixture into an electrical system not having a proper grounding means could cause metal parts of the fixture to carry electrical currents if any of the fixture wires, wire connections or splices were to become broken, cut or loose during the mounting or normal operation of the fixture. Under this condition, anyone coming in contact with the fixture would be subject to electrical shock, which could cause serious injury or death.
- DO NOT connect the bare or green insulation fixture ground wire to the black (HOT) current-carrying wire or the white (NEUTRAL) house wire. Connection of the bare or green fixture ground wire to the black or white house wires may cause metal parts of the fixture to carry electrical currents. Under this condition, anyone coming in contact with the fixture will receive an electrical shock, which could cause serious injury or death.
- DO NOT damage or cut the wire insulation (covering) during the installation of the fixture. DO NOT permit wires to contact any surface having a sharp edge. Doing so may damage or cut the wire insulation, which could cause serious injury or death from electrical shock.
WARNING
- All electrical connections must be in agreement with local codes and ordinances, the National Electric Code (NEC), and ANSI/NFPA 70-1999. Contact your municipal building department to learn about your local codes, permits, and/or inspections.
- To avoid personal injury, the use of gloves may be necessary while handling fixture parts with sharp edges.
- DO NOT suspend any fixture by the house wires. A fixture must always be mounted directly to a mounting plate that is first attached to the outlet box. All fixtures must be mounted to an outlet box that is supported by the building structure. Wire connectors will not support the weight of a fixture. Suspending a fixture by the house wires and wire connectors will result in the fixture falling, with the possibility of personal injury and the danger of electrical shock or fire.
- To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this light fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture. If your house wire is larger than 12 gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.
- To avoid water damage to the fixture or possible electrical malfunction, install the fixture at least 4 ft. above the ground/floor.
- Failure to caulk the fixture mounting surface with silicone weather sealant may result in water damage in the outlet box, which may cause electrical malfunction or electrical shock.
CAUTION
- TURN OFF ELECTRICITY at the main fuse box (or circuit breaker box) before beginning installation by removing the fuse (or switching the circuit breaker off).
- If you are not sure the lighting system has a grounding means, DO NOT attempt to install this fixture. Contact a qualified, licensed electrician for information regarding the proper grounding methods as required by the local electrical code in your area.
- DO NOT use bulbs having a wattage greater than the maximum value stated on the fixture. The use of bulbs with a higher wattage than specified will increase temperatures and the risk of fire.
- If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type to use as well as the electrical rating required.
- Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F. Consult a qualified electrician before installation.
- All fixtures must be mounted to an outlet box that is supported by the building structure.
PREPARATION
Before beginning the assembly of the product, make sure all parts are present. Compare parts with the package contents list and hardware contents. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 20 – 30 minutes
Tools Required for Assembly (not included): Flathead Screwdriver, Phillips
Screwdriver, Wire Strippers, Pliers, Wire Cutters, Safety Glasses, Stepladder,
Electrical Tape, Silicone Weather Sealant.
Helpful Tools (not included): A/C Tester Light, Do-It-Yourself Guide, Soft Cloth, Level.
ASSEMBLY INSTRUCTIONS
-
Turn off circuit breakers and wall switches to the fixture supply line lead.
DANGER: Failure to disconnect the power supply prior to installation may result in serious injury or death.
-
Remove the existing fixture and disconnect all electrical wiring.
-
Remove decorative nut (C) from the threaded nipple on the mounting strap (B). Save decorative nut (C) for later use.
-
Attach mounting strap (B) to outlet box (not included) using the existing washers and outlet box screws or the machine screws (BB). NOTE: If the outlet box screws required for your outlet box are of a different size than the machine screws (BB), consult with a licensed electrician before proceeding. Tighten machine screws (BB) completely to secure the mounting strap (B).
CAUTION: The fixture must be mounted to an outlet box that is supported by the building structure. Plastic outlet boxes are not recommended.
Hardware Used -
Unwrap BARE wire from BLACK and WHITE wires on the fixture (A). Prepare wire by stripping 3/4 inch of insulation from wire ends using wire strippers (not included).
-
Connect BARE/GREEN ground wire from outlet box to BARE wire from fixture (A) using wire connector (AA). Connect WHITE wire from fixture (A) to WHITE wire from the outlet box using wire connector (AA). Connect the BLACK wire from fixture (A) to the BLACK wire from the outlet box using a wire connector (AA).
NOTE: Screw wire connectors (AA) on in a clockwise direction.
WARNING: Never connect BARE/GREEN ground wire to WHITE or BLACK power supply wires.
WARNING: To reduce the risk of fire, electrical shock, or personal injury, wire connectors (AA) provided with this light fixture are designed to accept only one 12-gauge house wire and two lead wires from the light fixture. If your house wire is larger than 12 gauge or there is more than one house wire to connect to the corresponding fixture lead wires, consult an electrician for the proper size wire connectors to use.
Hardware Used -
Wrap electrical tape (not included) around each individual wire connector (AA) down to the wire.
WARNING: Make sure no bare wire or wire strands are visible after making connections. Carefully arrange excess wiring and wire connectors (AA) within the outlet box. -
Secure fixture (A) to mounting strap (B) with decorative nut (C) previously removed.
NOTE: Before tightening decorative nut (C) completely, use level (not included) to check fixture (A) — adjust if necessary. -
Item# 4145452 & 4145453:
Remove socket ring (D) from the socket of fixture (A). Attach shade (F) to the socket using socket ring (D). -
Item# 4145470:
Remove screws (E) from fixture (A). Attach shade (F) to socket with screws (E) just removed. -
Install one 60-watt max. standard-base incandescent bulb (not included) or CFL/LED equivalent.
WARNING: When replacing the bulb, allow the bulb, shade, and fixture to cool down before touching it.
Restore power and test fixture (A).
If the light does not function, please refer to TROUBLESHOOTING. -
After completing the installation, caulk fixture (A) mounting surface with silicone weather sealant (not included).
WARNING: Failure to caulk the fixture mounting surface with silicone weather sealant may result in water damage in the outlet box, which may cause electrical malfunction or electrical shock.
CARE AND MAINTENANCE
- Shut off the main power supply. Wipe the fixture with a soft, damp cloth. Do not use an abrasive cleaner.
TROUBLESHOOTING
WARNING: Before beginning work, shut off the power supply to avoid electrical shock.
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| Bulb will not light. | 1. Bulb is burned out. |
2. Power is OFF.
3. Faulty connection.
| 1. Replace the bulb.
2. Make sure the power supply is ON.
3. Check wiring and all connections.
Fuse blows out or circuit breaker trips.| 1. Crossed wires.
2. Power wire is grounded out.
| 1. Check to wire.
2. Check all connections.
WARRANTY
The distributor warrants all of its lighting fixtures against defects in materials and workmanship for one (1) year from the date of purchase. If within this period the product is found to be defective, take a copy of the bill of sale as proof of purchase and the product in its original carton to the place of purchase. The distributor will, at its option, repair, replace or refund the purchase price to the consumer. All costs of installation and removal of the fixture are the responsibility of the consumer. This warranty does not cover fixtures becoming defective due to misuse, accidental damage, or improper handling and/or installation and specifically excludes liability for direct, incidental, or consequential damages. As some states do not allow exclusions of limitations on an implied warranty, the above exclusion and limitation may not apply. This warranty gives you specific rights and you may also have other rights which may vary from state to state.
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-888-251-1003, 8 a.m. – 8 p.m., EST, Monday – Sunday. You could also contact us at partsplus@lowes.com or visit www.lowespartsplus.com.
HARBOR BREEZE and logo design are trademarks or registered trademarks of LF, LLC. All rights reserved.
Printed in China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>