FRICO TAP16R Electronic Thermostat User Guide
- June 8, 2024
- FRICO
Table of Contents
TAP16R Electronic Thermostat
User Guide
TAP16R Electronic Thermostat
Get started quickly and easily! Here you have a guide to the most important
functions and settings, an introduction to the energy saving programs and an
overview of the menu system.
Always read the full manual for complete product information.
Getting started
This is what the display looks like when you first start TAP16R.
Using the menu
*Or wait 30 secs and exit automatically.
Turning off and on
*The heat is not being regulated. The clock is running and the programming is saved in the memory.
Locking the keypad
Basic settings
Time and date
To be able to use all the functions you need to set the time and date first.
*Repeat the last two steps to set minutes, day, month and year. The correct day of the week is set automatically.
Desired temperature
Show actual temperature
- If the thermostat is set to external sensor, otherwise temperature in the room (R).
TAP16R can control the temperature in three different ways: with the External sensor, Room sensor or the Room sensor and external sensor in combination. If the External sensor is connected when the thermostat is switched on for the first time, this function is selected automatically. The Room sensor cannot be selected when the external sensor is connected. For the Room sensor and external sensor in combination, the built-in sensor controls the room temperature and the external sensor works as a temperature limiter. Learn more about control functions and how to set them in the manual. You can always see the current temperature by following the description above.
Energy saving programs
Save energy cleverly and easily! With these programs the heating is adapted to your actual needs and the heat is turned down when it isn’t needed. There are four program options:
| Preset for office environments
---|---
| Preset for home environments
| Program your own personal settings
| Frost protection for premises which stand empty for long periods
Start/stop program
*Stop program: Confirm when no icon is flashing.
Program personal settings
Tailor the heating to your own needs! You have the option of programming time
and temperature for four events every day: wakeup out home and night . An
example:
The family wakes up nice and warm at 07:30. Wakeup is programmed: 23 °C at
07:30.
They leave home and the heating can be turned down. Out is programmed: 17 °C
at 09:30.
The family return at 17:00 to a warm home. Home is programmed: 21.5 °C at
17:00.
A cool climate is better at night for both the environment and your sleep.
Night is programmed: 18 °C at 22.30.
Don’t forget to start the program afterwards!
Sitemap of the menu
This is how the menu in TAP16R is structured. Here you can quickly see where all the functions and settings are.
CONT
Set the display’s contrast| PROG
Start/stop program| UTIL
Show connected time in %
---|---|---
1-8| Home program
Office program
Personal program
Frost protection program| 24 HR
7 D
30 D
365 D
SET
Various settings
CLK
Set time and date.
S
Turn off and set to automatic change to DST
RNF
Set which sensor will control the temperature.
F (external sensor)
R (room sensor)
R&F (room sensor and external sensor combined)| OH
Set the temperature for limitation by the external sensor for R&F (not
normally used).
FP
Turn off and turn on the frost protection program.
4E
Set the personal program, time and temperature for up to four events per day.
DISP
Set how the time will be shown, 24- or 12-hour format.| LED
Set the strength of the display’s backlight.
AF
Turn off and turn on the adaptive function.
RST
Reverts to factory settings and deletes all personal settings.
END
Exit the menu and return to basic mode.
LOCK
Locks the keypad
END
Exits the menu
www.frico.se/en
Get In Touch
Call: 0845 6880112
Email: info@adremit.co.uk
Our Address
Puravent, Adremit Limited, Unit 5a,
Commercial Yard, Settle,
North Yorkshire, BD24 9RH
TAP16R EN 170830
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>