homestyles 5450-151 Merge 42 in. Brown Walnut Writing Desk Instruction Manual
- June 8, 2024
- homestyles
Table of Contents
5450-01
Personal Storage Unit
5450-151 Merge 42 in. Brown Walnut Writing Desk
IMPORTANT
Carefully remove all the parts from the carton and place them individually on
a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions to ensure a
completed product as designed.
Do not use power tools above 8 volts to assemble.
Assembly Instructions 2/7
IMPORTANT
- Use a soft cloth between these parts and the floor.
- Do not use power tools above 8 volts to assemble.
- Do not tighten all the screws until each part is properly assembled.
- The unit must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Top (A) and Side Panels (B),
(C), then tighten.
STEP 2
Attach Shelf (D) to Back Panel (F) with Dowels.
Assembly Instructions 3/7
STEP 3
Attach Side Panels (B) and (C) to unit with Dowels and Cam Locks. (See Figure
STEP 4
Attach Bottom (E) to unit with Dowels and 1 1/2″ Round Head Screws.
Assembly Instructions 4/7
STEP 5
Attach Top (A) to unit with Dowels and Cam Locks .
STEP 6
Turn unit to its upright position.
Cover Cam Lock with Caps. (See Figure 2)
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 3)
Note: Unit must be level to proceed.
Assembly Instructions 5/7
STEP 7
Attach Drawer Front (G 1) and Drawer Back (G2) to Drawer Side (G3) with 1 1/4″
Flat Head Screws.
STEP 8
Insert Drawer Bottom (GS) into groove. Attach Drawer Side (G4) to unit with
1 1/4″ Flat Head Screws.
STEP 9
Attach Handle with 3/4″ Flat Head Screws.
Note: Drawer assembly is not complete until 3/4″ Flat Head Screws are
used in a later step.
Assembly Instructions 6/7
STEP 10
Loosen slightly screws pre-installed on back of drawer front.
STEP 11
Insert drawer into unit, then adjust drawer front panel left or right and up
or down until drawer gaps look proportional.
STEP 12
Pull drawer open slowly, then re-tighten screws from Step 10. Make sure drawer
front panel does not move and lock drawer front panel into position with 3/4″
Flat Head Screws.
Note: These 3/4″ Flat Head Screws must be installed to complete the
drawer assembly.
Assembly Instructions 7/7
STEP 13
Place Metal Strips into position in Drawer (G).
Slide Drawer (G) into position.
Note: To remove Drawer (G) in future, push plastic lever on left side up,
push plastic lever on right side down and pull open. (See Figures 4 and 5)
CARE INSTRUCTIONS
home styles will provide replacements free of charge for missing or
damaged parts within 30 days of purchase. Digital images of the defective
parts may be required. If the product was not purchased from an authorized
retailer,
home styles is under no obligation to provide replacement parts. Parts
are not available for fully assembled items nor are parts available for sale.
Replacements for missing or damaged parts may be requested via contact info
below.
5450-15
Desk
IMPORTANT
Carefully remove all the parts from the carton and place them individually on
a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions to ensure a
completed product as designed.
Do not use power tools above 8 volts to assemble.
Tool(s) required for assembly: Phillips screwdriver, Level
Assembly Instructions 2/5
IMPORTANT
- Use a soft cloth between these parts and the floor.
- Do not use power tools above 8 volts to assemble.
- Do not tighten all the screws until each part is properly assembled.
- The unit must be level to work properly. Use the included adjustable levelers to level.
- Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Stretcher (D) to Side Frames (B) and (C) with Pins and Head Cap Bolts
(short).
Tighten Head Cap Bolts with Hex Wrench. (See Figure 1)
Assembly Instructions 3/5
STEP 2
Attach Rails (F) to unit with Head Cap Bolts (long).
Tighten Head Cap Bolts with Hex Wrench. (See Figure 2)
Assembly Instructions 4/5
STEP 3
Attach Stretcher (E) to unit with Head Cap Bolts (short).
Tighten Head Cap Bolts with Hex Wrench. (See Figure 3)
STEP 4
Attach Stretcher (E) to unit with Head Cap Bolts (short).
Tighten Head Cap Bolts with Hex Wrench. (See Figure 4)
Assembly Instructions 5/5
STEP 5
Attach unit to Top (A) with Head Cap Bolts (long).
Tighten Head Cap Bolts with Hex Wrench. (See Figure 5)
STEP 6
Turn unit over to its upright position.
Attach Tray (G) to unit with 3/4″ Flat Head Screws.
Level unit by adjusting the adjustable levelers on bottom of unit. (See Figure
6)
CARE INSTRUCTIONS
home styles Customer Service:
www.homestylesfurniture.com,
servicedesk@homestylesfurniture.com,
888-680-7460
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>