homestyles 6661-32 Dining Table Instructions
- June 3, 2024
- homestyles
Table of Contents
homestyles 6661-32 Dining Table Instructions
6661-32 Dining Table
IMPORTANT
Carefully remove all the parts from the carton and place them individually on
a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions to ensure a
completed product as designed.
This product is made of aluminum. Do not use power tools above 8 volts to
assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
Part List
-
A. Top 1 pc.
-
B. Leg 4 pcs.
-
C. Stretcher 4 pcs.
Hardware List
-
Hex Wrench 1 pc.
-
Wrench 1 pc.
-
Spring Washer 12 pcs. (+1 extra)
-
Nut 12 pcs. (+1 extra)
-
Small Hex Wrench 1 pc.
-
M8x30 Bolt 4 pcs. (+1 extra)
-
Flat Washer 12 pcs. (+1 extra)
-
Cap 12 pcs. (+1 extra)
-
Cover 1 pc.
Tool(s) required for assembly: Level
Assembly Instructions
IMPORTANT
- Use a soft cloth between these parts and the floor.
- Do not use power tools above 8 volts to assemble.
- Do not tighten all the bolts until each part is properly assembled.
- The unit must be level to work properly. Use the included adjustable levelers to level.
- Keep Wrench as the bolts may need to be tightened in the future.
-
STEP 1 Attach Legs (B) to Stretchers (C) with Flat Washers, Spring Washers and Nuts, tightening Nuts only halfway. (See Figures 1 and 2)
-
STEP 2
Place Top (A) upside down on a soft cloth.
Insert Bolts into pre-drilled holes in Top (A),
then tighten. (See Figure 3)
Attach unit to Top (A) with Flat Washers,
Spring Washers and Nuts,
tightening Nuts only halfway.
Tighten all Nuts used in Steps 1 and 2.
Cover all Nuts with Caps.
- STEP 3
Turn table over to its upright position.
Cover umbrella hole with Cover.
Level table by adjusting the adjustable levelers on bottom of legs. (See Figure 4)
CARE INSTRUCTIONS
NEVER allow liquids to remain on furniture.
Absorption causes parts to warp and split and finishes to delaminate.
-
Do not use power tools above 8 volts to assemble.
PREVENT CRACKING
-
Do not place in direct sunlight.
PREVENT FADING
-
Do not write directly on surface.
PREVENT MARKING
-
Do not place hot objects on surface.
PREVENT FINISH DAMAGE
-
Do not use rubber based placemats.
PREVENT DISCOLORING
-
Do not use commercial waxes and polishes.
PREVENT YELLOWING
-
CLEAN
with a soft cloth moistened in lukewarm soap and water. Buff with a dry clean cloth.
homestyles will provide replacements free of charge for missing or damaged parts within 2 years of purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer, homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items nor are parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
6661-53 Swivel Arm Chair
IMPORTANT
Carefully remove all the parts from the carton and place them individually on
a soft cloth to prevent scratches or other damage.
Carefully and strictly follow these assembly instructions to ensure a
completed product as designed.
This product is made of aluminum. Do not use power tools above 8 volts to
assemble and only tighten bolts until snug.
Over tightening can damage the aluminum.
Part List
-
A. Back 1 pc.
-
B. Seat 1 pc.
-
C. Arm 1 pc.
-
D. Arm 1 pc
-
E. Base 1 pc.
-
F. Connector 1 pc.
Hardware List
-
Hex Wrench 1 pc.
-
Wrench 1 pc.
-
M8x30 Head Cap Bolt (long) 2 pcs. (+1 extra)
-
Spring Washer (large) 6 pcs. (+1 extra)
-
Flat Washer (large) 2 pcs. (+1 extra)
-
Washer 4 pcs. (+1 extra)
-
M8x35 Bolt 4 pcs. (+1 extra)
-
Small Hex Wrench 1 pc.
-
M6x15 Head Cap Bolt 4 pcs. (+1 extra)
-
Spring Washer 4 pcs. (+1 extra)
-
Flat Washer 4 pcs. (+1 extra)
-
Nut 4 pcs. (+1 extra)
-
Cap 8 pcs. (+1 extra)
Assembly Instructions
IMPORTANT
- Use a soft cloth between these parts and the floor.
- Do not use power tools above 8 volts to assemble.
- Do not tighten all the bolts until each part is properly assembled.
- Keep Wrench and Hex Wrench as the bolts and nuts may need to be tightened in the future.
-
STEP 1
Attach Seat (B) to Back (A) with
Flat Washers (large), Spring Washers (large) and Head Cap Bolts (long), tightening bolts only halfway. (See Figure 1)
-
STEP 2
Attach Connector (F) to unit with Bolts,
Washers, Spring Washers (large) and Nuts, tightening bolts and nuts only halfway. (See Figure 2)
Tighten all Bolts and Nuts used in this step.
Cover all Bolts with Caps.
-
STEP 3
Place unit onto Base (E).
Attach Arms (C) and (D) to unit with Flat Washers, Spring Washers and Head Cap Bolts, tightening bolts only halfway.
Tighten all Head Cap Bolts used in Steps 1 and 3.
CARE INSTRUCTIONS
NEVER allow liquids to remain on furniture.
Absorption causes parts to warp and split and finishes to delaminate
-
Do not use power tools above 8 volts to assemble.
PREVENT CRACKING
-
Do not place in direct sunlight.
PREVENT FADING
-
Do not write directly on surface.
PREVENT MARKING
-
Do not place hot objects on surface.
PREVENT FINISH DAMAGE
-
Do not use rubber based placemats.
PREVENT DISCOLORING
-
Do not use commercial waxes and polishes.
PREVENT YELLOWING
-
CLEAN
with a soft cloth moistened in lukewarm soap and water.
Buff with a dry clean cloth.
homestyles will provide replacements free of charge for missing or
damaged parts within 2 years of purchase.
Digital images of the defective parts may be required. If the product was not
purchased from an authorized retailer, homestyles is under no obligation
to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged
parts may be requested via contact info below.
homestyles Customer Service:
www.homestylesfurniture.com,
servicedesk@homestylesfurniture.com,
888-680-7460
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>