SHARP MX-M5051 Multifunction Printer User Manual

: June 8, 2024
: Sharp

Table of Contents

SHARP MX-M5051 Multifunction Printer
Main functions for MX-M5051
Energy data of Sharp MX-M5051 according to DE-UZ 219
Overview of the operation modes of Sharp MX-M5051
Energy Consumption of Sharp MX-M5051
Further information and instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SHARP MX-M5051 Multifunction Printer

SHARP MX-M5051 Multifunction Printer-FIG1

User information related to environmental Label Blue Angel DE-UZ 219 for monochrome laser multifunction device Sharp MX-M5051

SHARP model MX-M5051 is a monochrome multifunction device for commercial use and is awarded with the environmental label Blue Angel according to DE-UZ 219 for multifunction devices. The conditions about this label can be found at the homepage of Blue Angel www.blauer‐engel.de

Main functions for MX-M5051

Main functions: Copying, Printing, Scanning

Number of copies/prints per minute
Monochrome print| 50
Colour print| –
Noise| Monochrome

print

| Colour print
Declared A-weighted sound power level

LWAd

Energy data of Sharp MX-M5051 according to DE-UZ 219

Information
Electric power consumption of a device depends on its characteristics and the way you use it. Sharp MFP model MX-M5051 is designed and set to save electricity costs. After the last use, it switches to “Ready” mode. From there, it can be used again immediately, if required. If not required, it switches to energy-saving modes in two steps after a certain time, called activation time. In these, it consumes less power (watts). If you want to use it again, the device will take a little longer from the energy-saving mode than from the “Ready” mode. This delay is called return time. The device is designed to be switched on and off up to twice a day in the switch-off mode without damage. This device does not have a power switch that can be used to completely disconnect the device from the mains. If you wish to do so, or if the device is not in use for a longer time, please disconnect the power plug of the device after switching off the device via the power button and the main power switch. The following table shows the individual values of the power consumption as well as the activation and return times. At the time of delivery, the values mentioned there are set. With them, the device meets the requirements of
Blue Angel.

Overview of the operation modes of Sharp MX-M5051

Print speed of A4 format according to ISO/IEC 24734
In monochrome printing: 50 pages/minute
In colour printing: – pages/minute

SHARP MX-M5051 Multifunction Printer-FIG3

- The values are measured in the as-shipped conditions without accessories.
** The activation time is the time that elapses after the end of the printing process until the device switches to the mode.
The figures in brackets indicate the range in which you can change the activation time.
- *** The return time is the time the device needs to return to ready mode for printing.

Energy Consumption of Sharp MX-M5051

For the standard use cycle according to ENERGY STAR 3.0 standard, the following assumptions are made for a device like Sharp MX-M5051:
32 print jobs per working day, each with 39 pages, single-sided using monochrome printing (1248 pages/day).
The energy consumption for a week (7-days’ week with 5 working days of 8 hours each) in the standard use cycle according to ENERGY STAR 3.0, determined using printing test pattern A according to ISO 10561:1999, is 0,79 kWh/week. This value was measured with the settings (delivery status) stated above. You can change the activation times for the energy-saving modes in some cases. If you shorten an activation time, the device will switch to an energy-saving mode faster and you will save electricity costs. If you nevertheless want to extend an activation time, please bear the following in mind:

The device will switch to an energy-saving mode later or not at all. The device will thus remain in a mode with higher power consumption for a longer period of time and will consume more electric power as a result. In addition, it is possible that the device will no longer comply with the maximum value for power consumption specified by the Blue Angel. We recommend that you do not extend the activation times.

Minimum use of PCR plastics
The proportion of post-consumer recycled plastic used in the device, calculated as a percentage of total plastic by 0-1%, 1-5%, 5-10%, 10-15%, 15-20%, etc. (in 5% intervals): 0-1 %

Further information and instructions

Installation instructions : New electronic devices may release volatile substances into the room air in the first days after unpacking. Therefore, you should take care for sufficient aeration at the installation site.
Guarantee: The guarantee period for the device corresponds to legal regulations.
Duplex print: The devices are pre-installed (factory setting mode) to duplex print; if necessary, they may divergently be configured by the user. It is, however, recommended to let the basic installation “duplex print” unchanged as it helps to reduce paper in combination with “N-up function”.
N-up function: This device offers the function to copy or print several pages per side of the sheet. Paper consumption is thereby reduced, especially in combination with duplex print.
Recycled paper: This device is suitable for processing recycled paper according to EN 12281:2002.
Individual user installations: Various individual installations can be made at the device and/or print driver by the user itself, among
others regarding the reduction of energy and paper.
Repair and supply of consumables: SHARP ensures the supply of spare parts and consumables for 5 years after discontinuation of the production of MX-M5051.
Maintenance of the device: Cleaning, maintenance and waste removal activities may only be done by trained personnel. Ozone and dust filters must be exchanged by trained personnel as well.
Instructions for handling toner cartridges: Do not open toner cartridges by force. Do not inhale and as a precaution avoid contact with the skin in case toner dust exits due to incorrect handling. Keep toner cartridges in a place inaccessible to children. Wash off the toner with cold water or with soap in case of skin contact. Upon skin irritation seek medical advice. The print supplies items provided and recommended by Sharp for compliance with the permissible emission limits have been checked and confirmed according to Blue Angel Eco Label.
Take back and disposal: Further information and contact details for the return of equipment from the used toner containers or residual toner containers are provided by the following website www.sharp.eu/BlueAngel
Please refer to Blue Angel award of your device.
The take back is free of charge. For the take back a point of transfer is agreed upon. The items will be recycled respectively mechanically recycled with priority. If required, photoconductor drums can exclusively be replaced by the field service. The appropriate recycling of photoconductor drums is done by the Service Partner or SHARP-Service. Documents about an effective disassembling and the selective substances to be treated will be provided to our recycling partners upon request.