Harbor Breeze ZDL1141-L5K8030Q LED Path Light Instruction Manual

: June 8, 2024
: Harbor Breeze

Table of Contents

Harbor Breeze ZDL1141-L5K8030Q LED Path Light
PREPARATION
TROUBLESHOOTING
CARE AND MAINTENANCE
- SAFETY INFORMATION
INSTALLATION OVERVIEW
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Harbor Breeze ZDL1141-L5K8030Q LED Path Light

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list. If any part is missing or damaged, do
not attempt to assemble the product.

Estimated Assembly Time: 10 minutes

FEELING CONFIDENT? START YOUR NEXT PROJECT

Visit www.lowes.com for more information Printed in China

TROUBLESHOOTING

|
---|---
PROBLEM| POSSIBLE CAUSE| CORRECTIVE ACTION|
The light does not turn on at night.|

The transformer is not plugged in or turned on.
Fixture connector is not properly installed on the low voltage cable.

|

Make sure the transformer is plugged in and turned on.
Make sure the contact pins pierce the wire insulation and make proper contact with the wire.

CARE AND MAINTENANCE

Clean the lens, lamp head and lamp stand regularly with a non-abrasive cleaner.

Warning: Always make sure the light is unplugged and completely cool before attempting to clean it.

WARRANTY

This fixture is warranted to be free from defects in materials and workmanship for five (5) years from the date of original purchase. Call 1-888-251-1003 to obtain a Return Authorization number and further instructions. The manufacturer will be liable for the replacement of the defective item and will not be liable for any other loss, damage, or injury which is caused by the product.

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install the product.

CAUTION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on.

The user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This product is not a toy and must not be operated by children.
Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Do not submerge in water. The product can be damaged.
Use with 18AWG minimum, underground low-voltage circuit cord.

WARNING

Be sure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. For use with low-voltage landscape lighting systems only
The wire is intended for shallow burial, less than 6 in. deep.
Risk of Electric Shock. Install all luminaires 10 ft. or more from a pool, spa or foundation.
Keep lamp away from material that may burn.
Do not touch hot lens, guard or hot fixture housing.
Do not operate or install a fixture with missing or damaged parts.
Do not touch the LED at any time as this may cause damage to the fixture.

PACKAGE CONTENTS

INSTALLATION OVERVIEW

Insert wire from low-voltage transformer (sold separately) into the wire guide by twisting the wire into each end of the wire guide. Align the pins on the connector top cover so that each pin lines up with opposite sides of the wire. Securely tighten the connector top cover making sure the pins completely pierce the plastic shield of the wire.