saxby lighting 99761 Albus CCT Instruction Manual
- June 8, 2024
- saxby lighting
Table of Contents
Instruction manual
Albus CCT
99761
99761 Albus CCT
Thank you for purchasing this light fitting. Please read the instructions
carefully before use to ensure safe and satisfactory operation of this
product. Please retain these instructions for future reference.
Warning
** This light fitting is double insulated and does not require connection
to an Earth circuit.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building
Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or
maintaining this fitting. Ensure other persons cannot restore the electrical
supply without your knowledge.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
If replacing an existing fitting, make a careful note of the connections.
This product is unsuitable for immersion in water.
This product is not suitable for location in or near a marine environment.
This system contains non-replaceable parts and cannot be serviced. If damage
occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Layout**
Plan the desired layout of these fittings carefully, ensuring the cables will
reach the distances between the junction box and each light fitting.
Avoid locating any cables in positions that would cause a hazard. Position
cables and outdoor rated junction boxes (not supplied) away from areas where
they may be at risk from being cut, trapped or damaged.
The mains supply cable must have a minimum cross section area of 1.0mm².
Cables must be protected using suitable conduit or plastic trunking.
Take care not to drill into any pipes or mains cables beneath the surface
during mounting holes preparation.
Installation
Exising fittings must be completely removed before installation of a new
product. Before removing the existing fitting, carefully note the position of
each set of wires.
Note that the power needs to be isolated/switched off at the fuse board.
Ensure that the screws and cable entry points are sealed to maintain the IP
rating of the product.
-
There colour bezels can be replaced, purchase your preferred bezel colour according to the product model. black color bezel is supplied in 99761 product, 99763— White bezel, 99764—-Silver bezel, see Fig. 1.
-
This product is colur changing and can be either warm white (3000K) or cool white (4000K) or daylight white (6500K).
Choose your preferred colour before installing by using the CCT switch. see Fig. 2. -
See Fig. 3. Select a mounting location for the product and cut a mounting hole 75mm diameter in the wall care not to foul any pipes, mains cables or joists beneath the surface. It is always recommended to cut the hole slightly smaller than the size specified, and then file the hole until the recessed unit fits snugly.
-
The Minimum wall void depth is 40mm. When more than one wall light is installed, the minimum distance between units is 500mm. The unit must be located a minimum distance of 50mm from a joist.
-
Ensure free movement of air by removing void insulation from at least 150mm from around the hole. Under no circumstances must these fittings be covered with insulating matting or similar material.
-
Pass the incoming supply cable through the cut out and through the housing supplied. Wire as detailed wiring.
-
Ensure that the product is sitting properly in the hole.
-
Switch on. Your light is now ready for use.
Wiring
having correctly identified the wiring from your existing light fitting and
connect to the terminal block (not supplied) in the following way:
Technical data
Supply Voltage: 220-240 V~, 50 Hz
Bulb Type: 1.5W LED module (SMD) CCT, 3000/4000/6500K
This product contains a light source of energy efficiency class G.
Non-replaceable light source
Non-replaceable control gear
** Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
The power supply is Double Insulated and does not require connection to an
Earth circuit.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
local store for recycling advice.
This product is not suitable for dimming.
This product is rated at IP65.
Caution!** Risk of electric shock!
Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive
cleaners as these could damage the finish.
For your safety, always switch off the power supply before cleaning.
V1 18/11/2021
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>