NATIONAL Tree COMPANY Unlit-Pre-Lit Plug-In Garlands Instruction Manual
- June 8, 2024
- NATIONAL Tree COMPANY
Table of Contents
Unlit / Pre-Lit Plug-In Garlands
Unlit-Pre-Lit Plug-In Garlands
CAUTION: IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupter (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
- This seasonal use product is not intended for permanent installation or use.
- Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
- Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
- Unplug the product when leaving the house, when retiring for the night, or if left unattended.
- Do not let lamps rest on the supply cord or any wire.
- CAUTION: This is an electrical product not a toy! To avoid risk of fire, burns, personal injury and electric shock, it should not be played with or placed where small children can reach it.
- Do not use this product for other than its intended use.
- Do not hang ornaments or other objects from cord, wire or light string.
- Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
- Never operate this product if the power cord or plug is damaged.
- Use only manufacturer specified replacement bulbs.
- Read and follow all instructions that are on the product or provided with the product.
USE AND CARE INSTRUCTIONS
- When storing the product, carefully remove the product from wherever it is placed, avoiding any undue strain or stress on the product conductors, connections, and wires.
- When not in use, store neatly in a cool, dry location protected from sunlight.
Shaping
The product is shipped from the factory with the branch tips compressed to the
center. Each branch tip must be shaped to its proper position to give the
product a natural look. This will also bring the piece to its advertised
dimension. The care and attention given to this final process will result in a
genuinely beautiful and appealing holiday decoration.
Shaping is done by gently grasping the branch tips and spreading them out away
from the center. The BEFORE photo shows the product as it appears out of the
box. The AFTER photo shows how the product should look after proper shaping.
Dual Color® Operating Instructions
(if equipped)
The hand switch operates the functions of the lights. There are 10 functions,
each one is activated with the press of the foot switch. Functions occur in
the following order:
Steady warm white; twinkle warm white; steady multicolor; twinkle multicolor;
steady pastel; fading warm white to multicolor; random fading; fading warm
white; fading multicolor; flashing warm white to multicolor.
Light functions always follow this sequence.
Bulb Replacement
-
Unplug light string from power source.
-
Pull up on the Base Lock™ unlatching the bulb from the bulb socket. Gently pull the bulb straight out (Figure 1).
-
Before inserting the new bulb into socket, make sure that the two wires on either side of the the bulb base are straight up and flush with the base (diagram at right).
-
Carefully insert new bulb into socket and push down Base Lock until it snaps into place (Figure 2).
LED Bulbs (Figure 3)
- Unplug light string from power source.
- Pull up on the Base Lock™ unlatching the bulb from the bulb socket. Gently pull the bulb straight out.
- Carefully insert new bulb into socket (bulb is keyed and only goes in one way) and push down Base Lock until it snaps into place.
NOTE: Fuse failure is sometimes a reason for non-functioning light strings. The fuses are found in the light string plug. If one is burnt out, replace it with a spare fuse included in the accessories bag.
Fuse Replacement
-
Unplug light string from power source.
-
Slide the fuse access cover away from cord side (in direction of arrow, Figure 4) exposing fuses.
-
Remove fuses from compartment and examine. Replace burnt out fuse with new one.
-
Close fuse compartment by sliding access cover back in towards cord side of plug (Figure 5).
SAVE THESE INSTRUCTIONS
2 Commerce Drive, Cranford, NJ 07016
www.nationaltree.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>