saxby lighting 78622 Rond LED Bulkhead Instruction Manual

June 8, 2024
saxby lighting

saxby lighting 78622 Rond LED Bulkhead

saxby-lighting-78622-Rond-LED-Bulkhead-PRODUCT

Installation

  • Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
  • Note that the switch is turned off before installation.
  • The ceiling surface must be flat and smooth to ensure a good fit.
  • Ensure the wall is capable of holding the weight of the product, or if fitting to a ceiling, ensure there is a joist at the point of fixing to support the weight of the product. Take care to avoid damaging any concealed
  • Wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
  • Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.
  • There are two bezel accessories can be chosen, Black plain bezel 78851 / Black eyelid bezel 78852, chose them as per your preferred.
  • Follow the installation steps below to install.
  • Replace fuse or circuit breaker and switch on. Your light is now ready for use.

saxby-lighting-78622-Rond-LED-Bulkhead-FIG-1

Wiring

Having correctly identified the wiring from your light fitting, pull the mains wire through the hole and connect to the quick fit connection block as shown on the right:

Check that…

  • You have correctly identified the wires.
  • The connections are tight.
  • No loose strands have been left out of the connection block.

Warning
The power supply is Double Insulated and does not require connection to an Earth circuit. Please read these instructions carefully before commencing any work. This unit must be fitted by a competent and qualified electrician. Check the pack and make sure you have all the parts listed. Install in accordance with the IEE Wiring regulations and current Building Regulations. To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician. This light fitting should be connected to a circuit with a 30mA RCD fitted. If replacing an existing fitting, make a careful note of the connections. This product contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distance between each light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables and junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged. The mains supply cable must have a minimum cross sectional area of 1.0mm2 Cables must be protected using suitable conduit or plastic trunking. The products can be wall or ceiling mounted. If wall mounting ensure that the power supply is at the bottom. This product is suitable for use in outside zones of a bathroom only. Please see below diagram. If this unit is being fitted in a room containing a bath or shower, a 30mA RCD must be used – in accordance with IEE regulations.

Technical data

  • Supply Voltage: 220-240 V~, 50 Hz
  • Bulb Type: 12W LED Module (SMD), 4000K This product contains a light source of energy efficiency class E.

``Non-replaceable light source

Non-replaceable control gear

  • Conformity with all relevant UKCA Directive requirements.
  • Conformity with all relevant EC Directive requirements.
  • The power supply is Double Insulated and does not require connection to an Earth circuit.
  • Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice
  • This product is not suitable for dimming
  • Caution! Risk of electric shock!
  • This product is rated at IP54.

Care and Safety

We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning..

For further information, please visit https://www.lighting-info.co.uk/78622

V2 21/12/2021 EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg UK Manufacturer: BH17 7BY www.saxbylighting.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

saxby lighting User Manuals

Related Manuals