Minoston

Z-Wave Mini Plug

SKU: MP31Z

Quickstart

This is a
secure
Binary Switch DT
for
.

To run this device please connect it to your mains power supply.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Z-WaveSmart Plug

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country- specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

1| 5|
---|---|---

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: Reaction of led

Parameter setting to change the reaction of LEDsetting.
Size: 1 Byte, Default Value: 2

SettingDescription

Parameter 2: Night led on time

Night Light ON time.
Size: 4 Byte, Default Value: 1572864

SettingDescription

Parameter 3: Night led off time

Night Light OFF time.
Size: 4 Byte, Default Value: 393216

SettingDescription

Parameter 30: Alarm setting

Determines if alarms are enabled in Switch, and whatSwitch will react to which alarms.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 31: Alarm response in device

Enabled by (Alarm settings), and determines what theswitch does in the case an alarm is triggered.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 32: Alarm disable setting

Determines the method of disabling the alarm of thedevice.
Size: 1 Byte, Default Value: 1

SettingDescription

Parameter 4: Indicator play duration

Setting indicator play duration.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 40: Auto turn off timer

Auto off after as soon as the switch turns ON
Size: 4 Byte, Default Value: 0

SettingDescription

Parameter 41: Auto turn on timer

Auto on after as soon as the switch turns OFF
Size: 4 Byte, Default Value: 0

SettingDescription

Parameter 5: Indicator speed

Select indicator flash speed.
Size: 1 Byte, Default Value: 5

SettingDescription

Parameter 7: Control turn off

Prevents the plug from being turned off via its button.
Size: 1 Byte, Default Value: 0

SettingDescription

Parameter 8: Restore status after power failure

Action in case of power out.
Size: 1 Byte, Default Value: 0

SettingDescription

Technical Data

Motor)LEDMLV (Magnetic)
Security V2| S2_UNAUTHENTICATED ,S2_AUTHENTICATED
Frequency| XXfrequency
Maximum transmission power| XXantenna

Supported Command Classes

• Association Grp Info V3
• Association V2
• Basic V2
• Switch Binary V2
• Clock
• Switch Color V3
• Configuration V4
• Device Reset Locally
• Firmware Update Md V5
• Indicator V3
• Manufacturer Specific V2
• Multi Channel Association V3
• Multi Channel V4
• Switch Multilevel V4
• Notification V8
• Powerlevel
• Scene Activation
• Scene Actuator Conf
• Security 2
• Supervision
• Transport Service V2
• Version V3
• Zwaveplus Info V2

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>