ABUS

Z-Wave Dual Pet PIR

SKU: PLBW10000

Quickstart

This is a
secure
Alarm Sensor
for
.

Please make sure the internal battery is fully charged.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.

Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message ( two- way
communication) and every mains powered node can act as a repeater for other nodes
( meshed network ) in case the receiver is not in direct wireless range of the
transmitter.

This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.

If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.

Product Description

Motion detectorIt uses Passive Infrared (PIR) technology to detect movement in a defined area by detecting the changes in thermal radiation caused by the moving body inside or outside the detection zone. With the dual PIR sensor (dual-lens technology), the sensor hides pets up to approx. 38kg, so that your pet can move freely without triggering the sensor. When the motion detector is triggered, an alarm signal is sent to the Z-Wave controller. The indicator LED lights up when motion is detected.Integrated temperature and humidity sensorAt periodic intervals, the unit automatically sends the measured temperature and humidity value to the Z-Wave controller or on request of the Z-Wave controller. Tamper protection between the device and wall bracketWhen the housing is opened, the tamper switch is triggered and the device sends a tamper alarm to the Z-Wave controller. The tamper contact must remain pressed for three seconds to reset the tamper alarm.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

1. Make sure a device is in factory reset state before including. In doubt exclude before include.
2. If inclusion still fails, check if both devices use the same frequency.
3. Remove all dead devices from associations. Otherwise you will see severe delays.
4. Never use sleeping battery devices without a central controller.
5. Dont poll FLIRS devices.
6. Make sure to have enough mains powered device to benefit from the meshing

Association – one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device
controlling another device is called association. In order to control a different
device, the controlling device needs to maintain a list of devices that will receive
controlling commands. These lists are called association groups and they are always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’ Command.

Association Groups:

Group NumberMaximum NodesDescription

1| 1| The Lifeline Association is automatically established between the Z-Wave controller and the device during inclusion and defines what information is exchanged between the Z-Wave controller and the device.Notification reportBattery reportDevice Reset Locally NotificationSensor Multilevel Report
---|---|---
2| 4| When the motion alarm is triggered, it sends a BASIC SET On / Off command to the nodes of group 2

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however
certain configuration can adapt the function better to user needs or unlock further
enhanced features.

IMPORTANT: Controllers may only allow configuring
signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: To set a
parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56.
In case of a two byte value the same logic applies: Values greater than 32768 may
needed to be given as negative values too.

Parameter 1: Temperature & Humidity Report

The interval time of the temperature and humidity report.
Size: 2 Byte, Default Value: 30

SettingDescription

Parameter 2: Waiting time between two motion alarms

Waiting time from one motion alarm to the next triggering.
Size: 2 Byte, Default Value: 160

SettingDescription

Parameter 3: Reset waiting time after motion alarm

Waiting time after a movement alarm until reset. Additionally, defines how long directly associated devices from group 2 are activated.
Size: 2 Byte, Default Value: 180

SettingDescription

Parameter 4: Temperature report threshold

Additional temperature report, which is sent when the set threshold is exceeded.
Size: 1 Byte, Default Value: 5

SettingDescription

0x0A)

Parameter 5: Humidity report threshold

Additional humidity report that is sent when the set threshold is exceeded.
Size: 1 Byte, Default Value: 5

SettingDescription

0x0A)

Parameter 6: LED status

Set whether the status LED lights up in case of a motion alarm.
Size: 1 Byte, Default Value: 1

SettingDescription

Technical Data

Supported Command Classes

• Association Grp Info
• Association V2
• Battery
• Configuration
• Device Reset Locally
• Firmware Update Md V4
• Manufacturer Specific V2
• Notification V8
• Powerlevel
• Security
• Security 2
• Sensor Multilevel V5
• Supervision
• Transport Service V2
• Version V3
• Wake Up V2
• Zwaveplus Info V2

Controlled Command Classes

• Basic

Explanation of Z-Wave specific terms

• Controller — is a Z-Wave device with capabilities to manage the network.
  Controllers are typically Gateways,Remote Controls or battery operated wall controllers.

• Slave — is a Z-Wave device without capabilities to manage the network.
  Slaves can be sensors, actuators and even remote controls.

• Primary Controller — is the central organizer of the network. It must be
  a controller. There can be only one primary controller in a Z-Wave network.

• Inclusion — is the process of adding new Z-Wave devices into a network.

• Exclusion — is the process of removing Z-Wave devices from the network.

• Association — is a control relationship between a controlling device and
  a controlled device.

• Wakeup Notification — is a special wireless message issued by a Z-Wave
  device to announces that is able to communicate.

• Node Information Frame — is a special wireless message issued by a
  Z-Wave device to announce its capabilities and functions.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>