Axis Communications Door/Window Sensor T8342-JP Manual
- June 8, 2024
- AXIS COMMUNICATIONS
Table of Contents
- Axis Communications
- Door/Window Sensor
- SKU: T8342-JP
- Quickstart
- Important safety information
- What is Z-Wave?
- Product Description
- Prepare for Installation / Reset
- Inclusion/Exclusion
- Communication to a Sleeping device (Wakeup)
- Quick trouble shooting
- Association – one device controls an other device
- Technical Data
- Supported Command Classes
- Controlled Command Classes
- Explanation of Z-Wave specific terms
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Axis Communications
Door/Window Sensor
SKU: T8342-JP
Quickstart
This is a
secure
Alarm Sensor
for
Japan.
Please make sure the internal battery is fully charged.
To add this device to your network execute the following action:
Auto inclusionThe detector supports the auto inclusion feature where it will
automatically enter Inclusion mode when first powered up. This willalso apply
when powered up after a factory reset.1. Put a Z-Wave controller into
inclusion mode.2. Remove the strip of insulating film from the battery cover
on the front of casing. The LED on the device should turn ON3. The inclusion
process should be completed when the LED stops blinking4. Perform test before
you refit the battery cover.Manual inclusionYou can also choose to manually
add the Z-Wave device to a control device. Please follow the steps described
below.NoteFor best results, exclude the device before starting the inclusion
process. For more details see the installation guide1. Press the tamper switch
3 times within 1.5 seconds to put the unit into learning (inclusion/exclusion)
mode.2. The inclusion process should be completed when the LED stops
blinking3. Perform a test before you refit the cover.
Please refer to the
Manufacturers
Manual
for more information.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in
this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any
loss or damage resulting from failure to comply with the instructions in this
manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal
instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart
Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message ( two-
way
communication) and every mains powered node can act as a repeater for other
nodes
( meshed network ) in case the receiver is not in direct wireless range of
the
transmitter.
This device and every other certified Z-Wave device can be used together
with any other
certified Z-Wave device regardless of brand and origin as long as both are
suited for the
same frequency range.
If a device supports secure communication it will communicate with other
devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to
maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc.
please refer
to www.z-wave.info.
Product Description
AXIS T8342 Door/Window Sensor is an easy to install, wireless sensor which enables triggering of a series of events such as notification messages, illumination and much more. With its support for wireless input/output connectivity, the door/window sensor can communicate wirelessly with AXIS M5065 PTZ Network camera or other connected Z-Wave Plus controllers, creating a small security solution with less cabling. Thanks to its integrated wireless I/O connectivity, AXIS T8342 enables flexible installation as the sensor can easily be mounted on a door, window, or cabinet according to your needs.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory
default
state. Please make sure to reset the device into factory default. You can do
this by
performing an Exclusion operation as described below in the manual. Every
Z-Wave
controller is able to perform this operation however it is recommended to use
the primary
controller of the previous network to make sure the very device is excluded
properly
from this network.
Reset to factory default
This device also allows to be reset without any involvement of a Z-Wave
controller. This
procedure should only be used when the primary controller is inoperable.
Factory Reset (This procedure should only be used when the controller is inoperable.)1. Press the tamper switch 3 times within 1.5 seconds to put the unit into exclusion mode.2. Within 1 second of step 1, press the tamper switch again and hold until LED is off (about 5 seconds).3. Node ID is excluded. The device reverts to 2-second on, 2-second off factory default state and will be in auto-inclusion mode for 4 minutes.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The
device needs
to be added to an existing wireless network to communicate with the
devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called
Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network.
This
controller is turned into exclusion respective inclusion mode. Inclusion and
Exclusion is
then performed doing a special manual action right on the device.
Inclusion
Auto inclusionThe detector supports the auto inclusion feature where it will automatically enter Inclusion mode when first powered up. This willalso apply when powered up after a factory reset.1. Put a Z-Wave controller into inclusion mode.2. Remove the strip of insulating film from the battery cover on the front of casing. The LED on the device should turn ON3. The inclusion process should be completed when the LED stops blinking4. Perform test before you refit the battery cover.Manual inclusionYou can also choose to manually add the Z-Wave device to a control device. Please follow the steps described below.NoteFor best results, exclude the device before starting the inclusion process. For more details see the installation guide1. Press the tamper switch 3 times within 1.5 seconds to put the unit into learning (inclusion/exclusion) mode.2. The inclusion process should be completed when the LED stops blinking3. Perform a test before you refit the cover.
Exclusion
Manual exclusion1. Detach the battery cover.2. Press the tamper switch 3 times within 1.5 seconds to put the unit into learning (inclusion/exclusion) mode.3. The exclusion process should be completed when the LED stops blinking4. Refit the battery cover.
Communication to a Sleeping device (Wakeup)
This device is battery operated and turned into deep sleep state most of the
time
to save battery life time. Communication with the device is limited. In order
to
communicate with the device, a static controller C is needed in the
network.
This controller will maintain a mailbox for the battery operated devices and
store
commands that can not be received during deep sleep state. Without such a
controller,
communication may become impossible and/or the battery life time is
significantly
decreased.
This device will wakeup regularly and announce the wakeup
state by sending out a so called Wakeup Notification. The controller can then
empty the mailbox. Therefore, the device needs to be configured with the
desired
wakeup interval and the node ID of the controller. If the device was included
by
a static controller this controller will usually perform all necessary
configurations. The wakeup interval is a tradeoff between maximal battery
life time and the desired responses of the device. To wakeup the device please
perform
the following action:
Wakeup Command ClassAfter it has been included into a Z-Wave network, the detector will go to sleep but will send a Wakeup Notification Command periodically at preset period to the controller. The detector will stay awake for 10 seconds at least and then go back to sleep to conserve battery life.The time interval between Wakeup Notification Commands can be set in the Wakeup Command Class based on the range values below:Minimum Wake Up Interval 600s (10 minutes)Maximum Wake Up Interval 86400s (1 day)Default Wake Up Interval 14400s (4 hours)Wake Up Interval Step Seconds 600s (10 minutesThe time interval between Wakeup Notification Commands can be set in the Wakeup Command Class based on the range values below:Minimum Wake Up Interval 600s (10 minutes)Maximum Wake Up Interval 86400s (1 day)Default Wake Up Interval 14400s (4 hours)Wake Up Interval Step Seconds 600s (10 minutes)
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Association – one device controls an other device
Z-Wave devices control other Z-Wave devices. The relationship between one
device
controlling another device is called association. In order to control a
different
device, the controlling device needs to maintain a list of devices that will
receive
controlling commands. These lists are called association groups and they are
always
related to certain events (e.g. button pressed, sensor triggers, …). In case
the event happens all devices stored in the respective association group will
receive the same wireless command wireless command, typically a ‘Basic Set’
Command.
Association Groups:
Group NumberMaximum NodesDescription
1 | 1 | Association with 1 node. |
---|---|---|
2 | 4 | Association with 4 nodes (i.e. end devices such as smart plugs and other |
lighting controllers). This allows the detector to transfer commands directly to end devices without the participation of the controller. This has the effect that when the detector triggers, all devices associated with detector will be operated.
Technical Data
Hardware Platform | SD3502 |
---|---|
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Firmware Version | HW: 1 FW: 1.01:00.01 |
Z-Wave Version | 6.71.01 |
Certification ID | ZC10-18015967 |
Z-Wave Product Id | 0x0364.0x0003.0x0001 |
Supported Notification Types | Access Control |
Color | White |
Security V2 | S2_UNAUTHENTICATED ,S2_AUTHENTICATED |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |
Supported Command Classes
- Association Grp Info
- Association V2
- Battery
- Device Reset Locally
- Firmware Update Md V4
- Manufacturer Specific V2
- Notification V4
- Powerlevel
- Security
- Security 2
- Supervision
- Transport Service V2
- Version V2
- Wake Up V2
- Zwaveplus Info V2
Controlled Command Classes
- Basic
Explanation of Z-Wave specific terms
-
Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers. -
Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls. -
Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network. -
Inclusion — is the process of adding new Z-Wave devices into a network.
-
Exclusion — is the process of removing Z-Wave devices from the network.
-
Association — is a control relationship between a controlling device and
a controlled device. -
Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate. -
Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>