YYR R1 True Wireless Earbuds User Manual

YYR R1 True Wireless Earbuds

CONTENTS

SET BEFORE USE

CHARGING

POWER ON/OFF

PAIRING

CONTROLS

RESET

BATTERY INDICATOR

CLEAN

Reset the earbuds

1. Put the earbuds into the charging case, make sure the charging case is fully charged, and then take out the left and right earbuds.
2. Quickly tab the touch keys on the left and right earbuds for 6 times, and this will clear the pairing records on the device.
3. Put them back into the charging case to charge, then take out the earbuds for re-pairing and connecting.
4. If the reset is unsuccessful, repeat the above steps.

Controls & LED Indicators

Streaming Audio Once paired, you can wirelessly stream audio on your device via earbuds. Music will automatically get paused when you receive an incoming phone call and will be resumed once the call ends.

Play or pause music

| Tap the touch-sensitive panel once on either earbud
---|---

Skip to previous track

| Long press 2s on the L earbud

Skip to next track

| Long press 2s on the R earbud

Thank you for purchasing the YYR R1 True Wireless Earbuds. Please read this user manual carefully and keep it for future reference. If you need any assistance, please contact our support team with your product model number.

Package Contents

• True Wireless Earbuds
• Charging Case
• Silicone eartips (S /L , M come attached to the earbuds)
• USB-A to C Cable
• User Manual

Product Diagram

Product Diagram

Earbuds

Charging Case

Getting Started

Charging
Fully charge the charging case before the first use. To charge, connect the case to a USB charger or charging port with the included USB-A to C cable to charge the charging case. When the LED charging indicator on the outside of the case changes from fashing blue to solid blue, the case is fully charged. Charging may take 1.5 hours, then case can ofer fully charge to the earbuds 3 times. The earbuds should be stored in the case when not in use.

Note

1. Remove the protective fle from the earbuds when using for the first time.
2. Using an adapter with an output voltage higher than 5V may not charge the battery or damage the device.

Turning On / Off

Turn On

| Open the lid of the charging case and take both earbuds out, the earbuds will automatically power on. To manually power on, tap and hold the touch- sensitive panels for 5 seconds until the LED indicator ashes blue and the voice guidance says “power on”.
---|---

Turn O

|

Return both earbuds to the charging case and close the lid, the earbuds will automatically power o . To manually power o , tap and hold the touch-sensitive panel for 5 seconds until the LED indicator ashes red and the voice guidance says “power o “. When the earbuds are not worn for about 5 minuts after being removed from the charging case, the earbuds turns o automatically.

Pairing

Starting with the earbuds in the case:

1. Open the lid of charging case and take both earbuds out, they will automatically turn on, indicators on both earbuds will frash blue and red alternately, and then enter pairing mode, the slave earbud indicator will be off.
2. Turn on the pairing function via BT on the device you want to pair with the earbuds
3. From the list of available devices, find and select “ YYR SONA R1”. After the connection is successful, the master earbud indicator will be off

Regular Use After Pairing

• Once the earbuds are successfully paired with your device, they can be switched on and ofi as follows:
• Open the lid of the charging case and take both earbuds out, then both earbuds will turn on and connect with each other automatically
• To turn off, put the earbuds back in the charging case and close the lid, They will begin charging

Using the Left / Right Earbud

Starting with the earbuds in the case

1. Take the left/right earbud out
2. Turn on the pairing function on the device you want to pair with the earbud
3. From the list of available devices, find and select “ YYR SONA R1”

Note

• When you turn on the earbuds, they will be automatically reconnected to the previous-paired device or enter pairing mode if no paired device is found
• Either left or right earbud can be used individually once connected to your device when you keep the other one inside the charging case
• The wireless operating range is 10m (33ft). If you exceed this range, the earbuds will lose connection with your paired device. The connection will be re-established if you re-enter the wireless range
• within 5 minutes. Or the earbuds will be switched off automatically after 5 minutes

Taking Calls

Answer a call

| Triple-tap the touch-sensitive panel on either earbud
---|---

Reject an incoming call or End a call

| Triple-tap the touch-sensitive panel on either earbud
Activate Siri or other voice assistants| Long-press the touch-sensitive panel on either earbud for 2 seconds
LED Indicator ( for earbuds)| Status
---|---
Solid red| Earbuds charging
O (after charging)| Charging case fully charged
Flashing red| Battery low

LED Indicator (for case)

FAQ

The earbuds are on, but not connecting to my device For the earbuds and your device to establish a connection, you need to put them both in pairing mode. Please follow the instructions in the Pairing section of this manual. I’ve connected the earbuds with my smartphone but can’t hear any sound Double-check the volume level on your smartphone and the earbuds. Some smartphones require you to set up the earbuds as an audio output device before the audio can be transmitted. If you’re using a music player or other device, please make sure it supports the A2DP profile. The sound isn’t very clear or the caller can’t hear my voice clearly Adjust the volume on your smartphone and the earbuds. Try moving closer to your smartphone to rule out the possibility of interference or wireless range-related issues. What’s the wireless range of the earbuds? The maximum range is 10m (33ft). However, the actual range depends on environmental factors. For optimal performance, keep your device connected within a range of roughly 4m to 8m and make sure that there are no major obstacles (like reinforced steel walls) between the earbuds and your device.

The earbuds won’t turn on

Try cleaning the charging the charging pins and then charging the earbuds for a while. If the earbuds still won’t power on, please contact our support team at the email address given in ‘Warranty & Customer Support.’ I put the earbuds back in the charging case, but the earbuds are still connected The charging case is probably out of power. Try charging it.

Product Care & Use

• Keep away from liquids and extreme heat
• Don’t use the earbuds at high volume for extended periods, as this may cause permanent hearing damage or loss
• Regular cleaning is recommended to prevent issues with charging.

Warranty & Customer Support

For questions, support, or warranty claims, please contact your seller directly.

Battery Warning

This product contains a built-in lithium battery. Do not expose the product to strong sunlight or fre or it might explode. Dispose of the battery according to local requlations. Do not dispose of it as domestic waste. Do not remove or replace the product battery unless doing so is specifed in the User Manual or in the Quick Start Guide, or you might damage the product

Safety Rules

1. Do not disassemble or reft the earphone for any reason as you may damage it or void the warranty.
2. Avoid contact with liquid to avoid serious damage to the earphone. The manufacturer does not cover water damage.
3. Avoid temperatures above 75 degrees and below minus 40 degrees.
4. Keep the indicator light away from children’s and animals’ eyes.
5. Do not use this product during thunderstorms to avoid electric shocks.

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 0mm the radiator your body: Use only the supplied antenna

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>