Revopoint 3D S1 Handheld Stabilizer User Manual

Revopoint 3D S1 Handheld Stabilizer

Product Introduction

The S1 Handheld Stabilizer’s gyroscopes provide high-precision stabilization for handheld scanning, helping to avoid loss of tracking and providing a smoother scan. The motorized axes allow you to smoothly pan or tilt the scanner as you move around the object.

Specifications

Strap x1
Note| *Operating time may vary depending on different scenarios and environments.

Functions Overview

① Bluetooth LED: The LED light flashes blue continuously while waiting for a connection. Once connected successfully, the LED turns solid blue.
② Joystick: Adjusts the tilt and pan.
③ 1/4 Threaded Hole: To mount the phone holder bracket.
④ ON/OFF Switch: Long-press to power on/off the Handheld Stabilizer. Press twice to change between Follow/Lock Mode.
⑤ Battery Level LED: Shows the remaining battery level. The LED light flashes continuously when charging and turns solid white when fully charged.
⑥ Start/Pause Button: Press to start or pause the scan. Press twice to recenter the Handheld Stabilizer

Charging the Handheld Stabilizer

1. Connect the USB-Type A end of the cable to an adapter, then plug it into a socket.
2. Plug the USB-Type-C end into the Handheld Stabilizer’s Type-C port.
3. The Handheld Stabilizer is fully charged when the battery LED turns solid white.
   

Connecting the Handheld Stabilizer to MINI 3D Scanners

1. Clip the MINI into the quick-release slot on top of the Handheld Stabilizer.
2. Connect and secure the Micro-B USB cable to the scanner.
   
   For freedom of movement, connecting the MINI via Wi-Fi is recommended when using the Handheld Stabilizer.

Using the Handheld Stabilizer with a PC via Wi-Fi

Power on the Handheld Stabilizer

Long-press the ON/OFF button to power on the Handheld Stabilizer. The Bluetooth LED flashes blue continuously when it is ready for connection.

Adding the Handheld Stabilizer via Bluetooth

Open your PC’s Bluetooth settings and look for a device named “REVO_STABILIZER”, then click Connect to add the Handheld Stabilizer.

Connecting to a PC’s Wi-Fi with MINI

Open the PC’s Wi-Fi settings and connect to the MINI’s Wi-Fi SSID.

Open Revo Scan to Start your Scan

1. Adjust the scanner’s position with the Handheld Stabilizer joystick.
2. Press the Handheld Stabilizer’s Start/Pause button to begin scanning.

Using the Handheld Stabilizer with a Smartphone via Wi-Fi

Attaching the bracket and phone holder

A. Insert and screw the bracket into the Handheld Stabilizer’s 1/4 threaded hole.
B. Attach the Phone Holder to the bracket
C. Insert your phone into the clamp.
Note: Use the Phone Holder that came with your MINI

Connecting to a smartphone’s Wi-fi with MINI

Open the smartphone’s Wi-FI settings and connect to the MINI’s Wi-Fi SSID.

Open Revo Scan to Start your Scan

1. Adjust the scanner’s position with the Handheld Stabilizer joystick.
2. Press the Handheld Stabilizer’s Start/Pause button to begin scanning.

FCC Warning

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference , and (2) this device must accept any interference received , including interference that may cause undesired operation .
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver .
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected .
• Consult the dealer or an experienced radio / TV technician for help

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>