MEGA-LITE EW1 LED Moving Head Wash Fixture User Manual

MEGA-LITE EW1 LED Moving Head Wash Fixture

Specifications

• Part Numbers: Fixture ID 1235-EW1

• Mechanical Specifications:

  • Housing: High Temp, Low flammability, Plastic
  • Mounting System: 2 Quick Release Clamp Mounts
  • Power Connection: Input Seetronics SAC3MPA Panel Mount Output Seetronics SAC3MPB Panel Mount Cable Seetronics SAC3FCA plug to Nema 5/15
  • Signal Connection: 3 and 5 Pin XLR In and Out (IP Rated)
  • Zoom: Lens: Infinity Lens Rotation
  • Weight: 32lb
  • Size: 15 X 9.37 X 19.37

• Electrical Specifications:

  • Light Source: 7 X 60W RGBW Osram 62 X .5W RGB
  • Lumen @ Full: 7625Lm
  • Color Temp White: 7562K
  • CRI: 72 @ full
  • Signal Support: DMX 512, RDM
  • Power: Electronic 90-250V AC 50/60
  • Power Consumption: 382Watts 3.25 Amps @110V
  • Power Factor: 0.99

• Control & Programming:

  • Protocol: RDM: DMX

  • Modes: DMX 512, Yes, Address, Channel Mode, Pan Invert, Tilt
    Invert, Pan and Tilt Swap, 27 Channel Mode, 103 Channel Mode

  • Operating Mode: Manual Settings Via Display

Product Usage Instructions

Main Power Connection

Caution!

1. Do not connect fixture to a dimmer system.
2. This unit must be earthed (electronically grounded).
3. Replace fuse only with the specified type and rating (F6AL250V).
4. This device is equipped with auto switching power supply that will allow the fixture to work from 90-250V AC 50/60Hz.

Cable USA: Black – Live, White – Neutral, Green – Ground

Cable EU: Brown – Live, Light Blue – Neutral, Yellow / Green – Ground

DMX-512 Connection

The fixture is equipped with 3 and 5 pin XLR Sockets for DMX input and output connection. The sockets are wired in parallel. Only use a shielded twisted pair cable designed for RS-485 and 3 or 5 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another.

DMX – Input:

1. Shield (Grd)
2. Signal (-)
3. Signal (+)

DMX – Output:

1. Shield (Grd)
2. Signal (-)
3. Signal (+)

Caution!

On the last fixture, the DMX signal needs to be terminated with a terminator. Pre-manufactured terminators are available for purchase from your Mega-Lite dealer item #P-DMX-T.

FAQ

Q: Can the fixture be used outdoors?

A: Yes, the fixture is designed for temporary outdoor use.

Q: What is the weight of the fixture?

A: The weight of the fixture is 32lb.

Q: What is the power consumption of the fixture?

A: The power consumption of the fixture is 382Watts at 3.25 Amps @110V.

Q: How should I connect the main power supply?

A: The main power connection should be done according to the provided cable instructions. For the USA, use the black cable for Live, white cable for Neutral, and green cable for Ground. For the EU, use the brown cable for Live, light blue cable for Neutral, and yellow/green cable for Ground.

Q: Can I connect the fixture to a dimmer system?

A: No, you should not connect the fixture to a dimmer system.

Check that the unit has not been damaged during transport.

Read all cautions and warnings prior to operation of this equipment

Protection Against Fire

1. Maintain a minimum of 1 foot distance from any type of flame.
2. Fixture is designed for temporary outdoor use.
3. Do not install the unit too close to a heat source.
4. Make sure cables are properly secured.
5. Maximum surface operating temperature: 130º.
6. Make sure fixture lens are not pointing towards the sun or direct light input.

Protection Against Electrical Fire

1. Disconnect power before servicing.
2. For connection to main power supply, proceed to page 4.
3. The power supply must be earthed (electronically grounded).
4. This fixture must not be left on for long periods of time.

Protection Against Mechanical Hazards

1. Use secondary safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit.
3. Do not open unit while it is on. Risk of electrical shock.

What is Included

• 1pc EW1 fixture
• 1pc Power Cable
• 2pc Quick Release Clamp Mount 1pc 1pc User Manual

Specifications

Part Numbers

Fixture ID
1235-EW1

Mechanical Specifications

• Housing: High Temp, Low flammability, Plastic
• Mounting System: 2 Quick Release Clamp Mounts
• Power Connection: Input Seetronics SAC3MPA Panel Mount
• Output Seetronics SAC3MPB Panel Mount
• Cable Seetronics SAC3FCA plug to Nema 5/15
• Signal Connection: 3 and 5 Pin XLR In and Out (IP Rated)
• Zoom: 4°to 36° Electronic Zoom
• Lens: Infinity Lens Rotation
• Weight: 32lb
• Size: 15” X 9.37” X 19.37”

Electrical Specifications

• Light Source: 7 X 60W RGBW Osram 62 X .5W RGB
• Lumen @ Full: 7625Lm
• Color Temp White: 7562K
• CRI: 72 @ full
• Signal Support: DMX 512, RDM
• Power: Electronic 90-250V AC 50/60
• Power Consumption: 382Watts 3.25 Amps @110V
• Power Factor: 0.99

Control & Programming

• Protocol: DMX 512
• RDM: Yes, Address, Channel Mode, Pan Invert, Tilt Invert, Pan and Tilt Swap
• DMX 2 Modes: 27 Channel Mode 103 Channel Mode
• Operating Mode: Manual Settings Via Display

Main Power Connection

Caution!

1. Do not connect fixture to a dimmer system.
2. This unit must be earthed. (Electronically grounded)
3. Replace fuse only with the specified type and rating. (F6AL250V)
4. This device is equipped with auto switching power supply that will allow the fixture to work from 90-250V AC 50/60Hz

DMX-512 Connection

The fixture is equipped with 3 and 5 pin XLR Sockets for DMX input and output connection. The sockets are wired in parallel. Only use a shielded twisted pair cable designed for RS-485 and 3 or 5 pin XLR plugs and connectors in order to connect the controller with the fixture or the fixture with another.

Caution!
On the last fixture the DMX signal needs to be terminated with a terminator. Pre-manufactured terminator are available for purchase from your Mega-Lite dealer item #P-DMX-T.

Display Control

The control board on the fixture base is your interface to access and control all the functions on the unit. It’s LCD display gives you a code view of the options and functions. The following will explain each function.

DMX Profile

EW1 DMX Profile|  |
---|---|---
27

Channel Mode

| 104

Channel Mode

|

Function

|

Description

|

Value

|

Init Value

1| 1| Pan| Pan| 0-255| 128
2| 2| Pan Fine| Pan Fine| 0-255| 128
3| 3| Tilt| Tilt| 0-255| 128
4| 4| Tilt Fine| Tilt Fine| 0-255| 128
5| 5| P/T Speed| Pan and Tilt Speed (fast to slow)| 0-255| 0
6| 6| Dimmer| Dimmer Off to Full (front leds)| 0-255| 255
7| 7| Dimmer Fine| Dimmer Fine (front leds)| 0-255| 255
8| 8| LED Intensity| Red| 0-255| 255
9| 9| LED Intensity| Green| 0-255| 255
10| 10| LED Intensity| Blue| 0-255| 255
11| 11| LED Intensity| White| 0-255| 255
 |  |  | No Function| 0-9|
 |  |  | Strobe (slow to fast)| 10-99|
12| 12| Strobe| Pulse Strobe (slow to fast)| 100-149| 0
 |  |  | Random Strobe All (slow to fast)| 150-199|
 |  |  | Random Strobe Each (slow to fast)| 200-255|
 |  |  | No Function| 0-3|
 |  |  | Macro 1| 4-24|
 |  |  | Macro 2| 25-45|
 |  |  | Macro 3| 46-66|
 |  |  | Macro 4| 67-87|
13| 13| Shutter Macro| Macro 5| 88-108| 0
 |  | (Requires| Macro 6| 109-129|
 |  | LED Intensity)| Macro 7| 130-150|
 |  |  | Macro 8| 151-171|
 |  |  | Macro 9| 172-192|
 |  |  | Macro 10| 193-213|
 |  |  | Macro 11| 214-234|
 |  |  | Macro 12| 235-255|
14| 14| Macro Speed| Macro Speed (slow to fast)| 0-255| 0
 |  |  | No Function| 0-9|
 |  |  | Color Fade All| 10-49|
 |  |  | Color Snap All| 50-99|
 |  |  | Color Effect 1| 100-109|
 |  |  | Color Effect 2| 110-119|
 |  |  | Color Effect 3| 120-129|
 |  |  | Color Effect 4| 130-139|
 |  |  | Color Effect 5| 140-149|
15| 15| Color Effect| Color Effect 6| 150-159| 0
 |  |  | Color Effect 7| 160-169|
 |  |  | Color Effect 8| 170-179|
 |  |  | Color Effect 9| 180-189|
 |  |  | Color Effect 10| 190-199|
 |  |  | Color Effect 11| 200-209|
 |  |  | Color Effect 12| 210-219|
 |  |  | Color Random Fade All| 220-227|
 |  |  | Color Random Snap All| 228-255|
16| 16| Effect Speed| Effect Speed (slow to fast)| 0-255| 0
---|---|---|---|---|---
17| 17| CTO| 8000K to 2000K (front LEDs)| 0-255| 0
18| 18| Ring LED Intensity| Ring Red LED| 0-255| 0
19| 19| Ring LED Intensity| Ring Green LED| 0-255| 0
20| 20| Ring LED Intensity| Ring Blue LED| 0-255| 0
 |  |  | No Function| 0|
 |  |  | Ring Macro 1| 1-8|
 |  |  | Ring Macro 2| 9-16|
 |  |  | Ring Macro 3| 17-24|
 |  |  | Ring Macro 4| 25-32|
 |  |  | Ring Macro 5| 33-40|
 |  |  | Ring Macro 6| 41-48|
 |  |  | Ring Macro 7| 49-56|
21| 21| Ring Shutter Macro| Ring Macro 8| 57-64| 0
 |  | (Requires Ring| Ring Macro 9| 65-72|
 |  | LED Intensity)| Ring Macro 10| 73-80|
 |  |  | Ring Macro 11| 81-88|
 |  |  | Ring Macro 12| 89-96|
 |  |  | Ring Macro 13| 97-104|
 |  |  | Ring Macro 14| 105-112|
 |  |  | Ring Macro 15| 113-120|
 |  |  | Ring Macro 16| 121-128|
 |  |  | Ring Macro 17| 129-136|
 |  |  | Ring Macro 18| 137-144|
 |  |  | Ring Macro 19| 145-152|
 |  |  | Ring Macro 20| 153-161|
 |  |  | Strobe| 162-193|
 |  |  | Random Strobe All| 194-225|
 |  |  | Random Strobe Segment| 226-255|
22| 22| Ring Macro Speed| Macro Forward Speed (fast to slow)| 0-127| 0
 |  |  | Macro Reverse Speed (slow to fast)| 128-255|
 |  |  | No Function| 0-1|
 |  |  | Red Back Ground| 2-21|
 |  |  | Green Back Ground| 22-41|
 |  |  | Blue Back Ground| 42-61|
 |  |  | Yellow Back Ground| 62-81|
 |  |  | Cyan Back Ground| 82-101|
 |  |  | Magenta Back Ground| 102-121|
 |  |  | Lime Back Ground| 122-141|
 |  |  | Purple Back Ground| 142-160|
23| 23| Ring Color Effect| White Back Ground| 161| 0
 |  | (Multiple Colors)| Multi Color Effect 1| 162-168|
 |  |  | Multi Color Effect 2| 169-176|
 |  |  | Multi Color Effect 3| 177-192|
 |  |  | Multi Color Effect 4| 193-200|
 |  |  | Multi Color Effect 5| 201-208|
 |  |  | Multi Color Effect 6| 209-216|
 |  |  | Multi Color Effect 7| 217-224|
 |  |  | Multi Color Effect 8| 225-255|
24| 24| Ring Effect Speed| Effect Forward Speed (fast to slow)| 0-127| 0
 |  |  | Effect Reverse Speed (slow to fast)| 128-255|
25| 25| Zoom| Zoom (wide to narrow)| 0-255| 255
 |  |  | No Function| 0-5|
 |  |  | Lens Rotation Clockwise (index)| 6-47|
 |  |  | Lens Infinite Rotation Clockwise (slow to fast)| 48-81|
26| 26| Lens Rotation| Lens Infinite Rotation Counter Clockwise (slow to fast)| 82-123| 0
 |  |  | Lens Rotation Clockwise (index) No Center LED| 124-165|
 |  |  | Lens Infinite Rotation Clockwise (slow to fast) No Center LED| 166-207|
 |  |  | Lens Infinite Rotation Counter Clockwise (slow to fast) No Center LED| 208-255|
 |  |  | No Function| 0-49|
---|---|---|---|---|---
 |  |  | Pan & Tilt Reset (Hold for 5 Seconds)| 50-100|
27| 27| Control| Lens and Zoom Reset (Hold for 5 Seconds)| 101-230| 0
 |  |  | All Function Reset (Hold for 5 Seconds)| 231-245|
 |  |  | No Function| 246-255|
n/a| 28| LED 1| Red 1| 0-255| 0
n/a| 29| LED 1| Green 1| 0-255| 0
n/a| 30| LED 1| Blue 1| 0-255| 0
n/a| 31| LED 1| White 1| 0-255| 0
n/a| 32| LED 2| Red 2| 0-255| 0
n/a| 33| LED 2| Green 2| 0-255| 0
n/a| 34| LED 2| Blue 2| 0-255| 0
n/a| 35| LED 2| White 2| 0-255| 0
n/a| 36| LED 3| Red 3| 0-255| 0
n/a| 37| LED 3| Green 3| 0-255| 0
n/a| 38| LED 3| Blue 3| 0-255| 0
n/a| 39| LED 3| White 3| 0-255| 0
n/a| 40| LED 4| Red 4| 0-255| 0
n/a| 41| LED 4| Green 4| 0-255| 0
n/a| 42| LED 4| Blue 4| 0-255| 0
n/a| 43| LED 4| White 4| 0-255| 0
n/a| 44| LED 5| Red 5| 0-255| 0
n/a| 45| LED 5| Green 5| 0-255| 0
n/a| 46| LED 5| Blue 5| 0-255| 0
n/a| 47| LED 5| White 5| 0-255| 0
n/a| 48| LED 6| Red 6| 0-255| 0
n/a| 49| LED 6| Green 6| 0-255| 0
n/a| 50| LED 6| Blue 6| 0-255| 0
n/a| 51| LED 6| White 6| 0-255| 0
n/a| 52| LED 7| Red 7| 0-255| 0
n/a| 53| LED 7| Green 7| 0-255| 0
n/a| 54| LED 7| Blue 7| 0-255| 0
n/a| 55| LED 7| White 7| 0-255| 0
n/a| 56| Ring LED 1| Ring Red 1| 0-255| 0
n/a| 57| Ring LED 1| Ring Green 1| 0-255| 0
n/a| 58| RingLED 1| Ring Blue 1| 0-255| 0
 |  | ” “| ”                             “|  |
n/a| 101| Ring LED 16| Ring Red 16| 0-255| 0
n/a| 102| Ring LED 16| Ring Green 16| 0-255| 0
n/a| 103| Ring LED 16| Ring Blue 16| 0-255| 0

Size and Weight

Segment

Installation

Caution!

1. The Installation must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injuries, if you have doubts concerning the safety do not install.
3. Unit is to be 24 inches away from flammable materials.
4. Use high quality installation equipment to hang the unit.
5. Internal Fan Filters must be cleaned periodically as not to block airflow.

When rigging the it is very important that you follow common safety procedures. Rigging requires extensive experience including but not limited to calculating working weight loads, material being used and periodic safety inspections. If you lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secure with a secondary safety attachment. The installation location of the fixture has got to be built in the way that it can hold 10 times the weight for 1 hour with out any failures. Installation should be checked at least one time a year by a skilled professional.

General Terms & Conditions

1. All resellers must have approved and signed Reseller Application on file, including their respective state tax information and W-9. Applications are re-evaluated on a fiscal calendar year basis to assure business integrity and tax status.

2. Cash, check, cashiers check, ACH, wire transfer, MasterCard, Visa, Discover, and American Express are accepted forms of payment.

3. Past due invoices will be charged 1.5% per month finance charge. Uncollected invoices are subject to be turned over to collection.

4. The reseller will pay all reasonable expenses incurred in the course of collections.

5. The proper venue for litigation will be Bexar County, Texas.

6. Returned checks will be charged a $50.00 fee.

7. All prices are in U.S. Dollars.

8. All prices and specifications are subject to change without notice, sales order confirmations are emailed and will reflect correct pricing.

9. All terms are insured, monitored, analyzed and approved by Coface USA. Changes in credit line and approved terms can change without notice. Company authroization of credit is based on Coface
   approvals. Any conflicts or disagreements should be referred to: 650 College Rd East Suite 2005 Princeton, NJ 08540. 1-609-469-0400. E-mail: cofaceusa@coface.com

10. Returns are subject to 25% restocking charge plus any necessary charges for repair or re-packaging.

Shipping Terms & Conditions

1. All orders are EXW San Antonio, TX (EXW means that a buyer/reseller incurs the risks for bringing the goods to their final destination) any deviation needs to be done in writing.
2. UPS ground shipping is the preferred shipping method. Requests for specific carriers may require use of the customer’s account number and may incur an additional charge for handling.
3. Drop shipments are subject to all return charges at resellers expense. Drop shipments are not allowed outside of the territorial United States.
4. NO C.O.D. shipments allowed.
5. Returned and undelivered shipment charges are the buyer/resellers responsibility and will be billed to the buyer/reseller.
6. The freight carrier and Company shipping@mega.lighing should be notified upon receipt of damaged freight, discrepancies, or non-conformities within 24 hours. Company can assist in making claims with carriers or agents in the event of any loss or damage.
7. Upon acceptance in good order by Carrier from Company, the material becomes the property of the Reseller.

Warranty and Service Procedures

1. All returns require an RMA# (Return Merchandise Authorization number) before returning goods for any reason. For a service or warranty RMA, please email service@mega.lighting or call (210)684-2600. For sales or demo returns, please contact sales@mega.lighting.
2. Case will be created and an RMA notice will be emailed. All units received must have the RMA # included with the unit as well as on the shippping label.
3. All shipping charges are the responsibility of the customer: MEGA Systems, Inc., Service, 18668 HWY 16 N., Helotes, TX 78023

Warranty for Products Purchased Before 2021
Unless otherwise stated in writing, product is covered by a one year parts and labor limited warranty and is subject to same limitations listed under the limited warranty exclusions listed below.

Warranty for Products Purchased After January 1, 2021
MEGA SYSTEMS INC (”MSI”) hereby warrants to the original purchaser/owner (Customer”), MSI products to be free of manufacturing defects in material and workmanship, for the warranty periods as defined below from the original purchase invoice date. This warranty applies exclusively to new MSI branded and/or distributed products listed below, purchased from an MSI AUTHORIZED dealer/reseller. This warranty is not transferrable and may or may not apply to products sold and/or forwarded outside the United States. Please contact MSI for applicable regional product warranty information.

The purchase of MSI product constitutes the Customer’s acceptance of all warranty terms and conditions as listed in this limited warranty statement. This warranty provides the Customer with legal rights, which may vary from state to state. Please contact MSI regarding warranty questions prior to purchasing.

Battery: 183 days/six months 2. Parts and Labor: 365 days/one year 3. Parts and Labor: 730 days/two years 4. Parts and Labor: 1095 days/three years

This limited warranty excludes any defects caused by, resulting from, or relating to the following:

• Normal wear and tear of lamps, color media, brushes, contact rings, lamp sockets, belts and other parts prone to wear and tear.
• Misuse, abuse, improper handling, accident, alteration or attempts to repair by or on behalf of the owner or any person not authorized by MSI.
• Damage to the product resulting from acts of God, including but not limited to, earthquakes, hurricanes, tornadoes, lightning and other natural disasters, fire, explosion, flood, riots, civil disorder or any other cause beyond the reasonable control of MSI.
• Exposure to harsh or excessively corrosive environmental conditions (whether indoors or outdoors) including, but not limited to, extreme temperature, humidity, atmospheric conditions (including salinity or pressure), radiation (UV, infrared or nuclear), shock and conditions which exceed the product’s Ingress Protection (”IP”) rating.
• Use of the product in a manner which exceeds the applicable product specification, including, but not limited to, exposure to excessive, insufficient, or other voltage conditions.
• Installation or use of the product not in accordance with the technical documentation, MSI guidelines (as may be posted on its website at www.megasystemsinc.com from time to time or otherwise designated by MSI or its brands) or applicable building and electrical codes, regulations, and standards.
• Failure to maintain the product in accordance with the technical documentation.
• Natural degradation and color shift of the LED source over the course of normal product use.
• Slight deviations in the specified values of intensity and color that do not affect the functionality of the product.
• Use of the product not for its intended purpose.
• All warranty claims are evaluated under the terms of this limited warranty. If a product falls within the warranty period and if, upon examination by MSI, it is found to have failed for a covered cause, MSI will, at its sole discretion, repair or replace the defective part or product or reimburse the purchaser a pro-rated portion of the purchase price based on the percentage of the warranty period still remaining as of the date that the returned product was received by MSI. Should a replacement part or product be discontinued or unavailable, MSI reserves the right, in its sole and absolute discretion, to substitute a comparable replacement part or product for the defective part of product. MSI warranty obligation herunder is limited solely to the repair or replacement of or reimbursement for the particular parts or products determined by MSI to have failed for a covered cause within the warranty period. In no event shall MSI be responsibile to replace or reimburse purchaser for any products or portions of a system that MSI determines has not failed for a covered cause within the warranty period, even if such other products or portions of a system are used together with products being repaired or replaced by MSI under this warranty and the repaired product differs in brightness, colors or any other attribute after the repair.
• Costs of removal, shipping to MSI or its authorized representative and reinstallation are solely the responsibility of the purchaser. If MSI determines that the product is covered by this limited warranty, it will only pay for parts and labor as indicated by product type. If MSI determines that the product is not covered by this limited warranty, the purchaser will have the option of paying for the repair if the product can be repaired and the purchaser shall be responsible for the cost of shipping the repaired product back to the purchaser. MSI reserves the right, in its sole and absolute discretion, to decline any repair.
• IN NO EVENT SHALL MEGA SYSTEMS, INC. BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, INDIRECT OR PUNITIVE LOSS OR DAMAGE OF ANY KIND, INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUES, LOSS OF USE OF THE PRODUCT OR ANY OTHER GOODS OR ASSOCIATED EQUIPMENT, DAMAGE TO ANY ASSOCIATED EQUIPMENT, COST OF CAPITAL, COST OF SUBTITUTE PRODUCTS, FACILITIES OR SERVICES, DOWN TIME COST, INSTALLATION OR LABOR COSTS, OR CLAIMS OF THE PURCHASER’S CUSTOMERS, WHETHER BASED ON WARRANTY, CONTRACT OR NEGLIGENCE, ARISING IN CONNECTION WITH THE SALE, USE OR REPAIR OF THE PRODUCT. MEGA SYSTEMS INC’S MAXIMUM LIABILITY SHALL NOT, IN ANY CASE, EXCEED THE PURCHASE PRICE OF THE PRODUCT THAT GIVES RISE TO THE CLAIM.
• EXCEPT FOR THE LIMITED WARRANTY SET FORTH HEREIN, ALL PRODUCTS SOLD BY MEGA SYSTEMS, INC. ARE SOLD “AS IS” WITHOUT ANY WARRANTY, EXPRESS, OR IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ALL OF WHICH ARE EXPRESSLY AND SPECIFICALLY DISCLAIMED BY MEGA SYSTEMS, INC.

Customer Support

MEGA-Lite has a customer support line to provide set-up help and to answer any questions should you encounter a problem. Please visit our website for any other related technical documents. For service related issues, please contact our service dept.
Monday – Friday 9am to 6pm CST
(210)684-2600
Service@mega.lighting

Manual Version

Please visit www.mega.lighting for the most up-to- date manual version.

MEGA-LITE
18668 Highway 16N
Helotes, TX 78023
Phone (210)684-2600 / Fax (210)855-6279
www.mega.lighting / info@mega.lighting

References

• Buy Stage Lighting Equipment, Controls & Truss Structures | Texas | Mega Systems Inc

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>