RM ITALY KL505 HF 10m Linear Amplifier User Guide

June 8, 2024
RM ITALY

RM ITALY KL505 HF 10m Linear Amplifier

RM ITALY-KL505-HF-10m-Linear-Amplifier-PRODUCT

Specifications

  • Operation Frequency: 10m Amateur Band, (1.8-30MHz with LPF)
  • Modulation Types: SSB,CW, AM, FM, (All narrowband modes)
  • Transistor: 4x RM SD1446 Transistor
  • Max I/P Current: 35A
  • Power Supply: 13.8VDC+/- 1V 50A
  • Input Fuse (Internal): 3x12A (5x20mm Fast Blow Glass Fuse)
  • Input RF Power: 1-10W max (All modes)
  • Output RF Power: 230W max
  • Maximum bypass power (Amplifier off): 50W max
  • Input VSWR: 1.1—1.5:1
  • Output VSWR Maximum: 2.5:1

WARNING: Before using this product please read carefully all of the information in this manual or at least the quick start guide!!! To avoid damage or incorrect operation this is extremely important.

Quick Start Guide

A more complete guide to the installation is featured later

  1. Connect the RTX input connector to transceiver with 50 Ohm patch cable
  2. Connect the ANT Output of the Amplifier to SWR Bridge / Wattmeter (If required), and then the An-tenna (50 Ohm load Impedance)
  3. Connect the Amplifier DC power Cable to a suit-able 13.8VDC (± 1V) 50A Power Supply or Auto Battery. Pay attention to the correct polarity
  4. Make sure that the amplifier is switched off
  5. Adjust the Transceivers RF output power to 5W (10W max) if it is capable of more than 10W out-put
  6. Switch on the Amplifier and start operating
  7. Check that the antenna VSWR is acceptable with the amplifier in use. Any large increase in VSWR indicates that the Antenna is not suitable for the power being used. Operation should be halted immediately to avoid damage to the Amplifier /Radio / ATU etc.

Front / Rear Panel Description

RM ITALY-KL505-HF-10m-Linear-Amplifier-
FIG-1

  1. Receive Pre-Amplifier ON / OFF Switch
  2. Amplifier ON / OFF Switch
  3. Input Attenuator 6 position, (For output power adjustment).
  4. AM / SSB Switch
  5. Pre Amplifier ON LED
  6. Amplifier ON LED
  7. TX indicator LED

Rear PanelRM ITALY-KL505-HF-10m-Linear-Amplifier-
FIG-2

  1. RTX SO239 RF input connector
  2. DC Input power connector. (Polarity is marked on the supplied mat-ing connector)
  3. ANT RF Output SO239 Socket to Antenna

Installation

Unpack the amplifier from it’s shipping carton and inspect for any signs of damage. The amplifier should be installed (either fixed or mobile installation), in a place that allows good ventilation and provides a suitable base to support it. Failure to allow for reasonable ventilation will cause the amplifier to overheat and damage may occur. A short 50 Ohm patch lead should be used to connect the amplifiers RTX SO239 input [ connector to the output, (Antenna Socket) of the drive Radio. This length of this cable is not critical but should be of good quality and be kept as short as practically possible. The ANT output ] connector of the amplifier should then be connected to antenna being used. (If an external VSWR/Power meter is to be used the amplifier should be connected to the input and then the antenna to the output, This order of connection is very important. Check also that the Antenna is suitably rated for the power output level. (Antenna VSWR should not change much from low to high power). The antenna should be tuned before connecting the power amplifier or with the amplifier switched OFF! .
In SSB mode the front panel switch ^ should be set to SSB. This adds a short delay to the release time of the RTX relays so that pauses in speech do not cause the RTX relay to drop out. In AM or FM mode the SSB delay switch should be set to AM.
The amplifier must be connected via the input power connector \ to a suitable power supply of the correct voltage output and sufficient current rating. The output should be 13.6 / 13.8V DC but the amplifier may be connected to a supply from 12V to 14V DC without damage. The current rating of the power supply must be at least 50A continuous. Be aware that the current rating must be greater still if the drive radio is also connected to the same power supply, although this is not generally advised.
The voltage output and current rating are very important for low voltage (12V) RF tran-sistors as voltage sag, (poor load regulation) or insufficient current capability can drasti-cally reduce the output power or cause distortion. If full output is not seen then the first thing to check is that the voltage remains above 12.5V at full load. Anything less indi-cates the power supply is not suitable for the amplifier at full output.
The cross sectional area of the cables used to connect the amplifier to the PSU should not be less than 10mm² or 7 AWG. They should also be kept as short as practicably possible to avoid voltage drop due to ohmic losses. This is less of a problem in a fixed installation where the power supply may be placed close to the amplifier.
For a mobile installation the leads should not exceed a length of 3m and they should be connected directly to the auto battery. An additional fuse may also be connected inline to provide protection in case of cable short circuit to chassis ground from the amplifier to the battery.
The installation location must also provide a suitable ground system both for RF and the AC power supply, (if used). This is very important safety requirement for any radio trans-mission equipment but as power increases becomes increasingly important. A good RF ground will also help to prevent any returned RF from causing problems with the equip-ment. Usually erratic operation of equipment when in transmission may be attributed to RF being present or poor RF grounding. Installations where a good RF ground is not pos- sible, like operation above the ground floor may require alternative solutions such as arti-ficial earths or the connection of 1/4 wave counterpoises to the operating equipment. Cor-rect RF earthing techniques are however beyond the scope of this manual.
Mobile use should ensure that the ground connections are well bonded to the vehicle chassis ground for best operation.
Operation:
Before using the amplifier the user must be familiar with all of the controls and be sure that it has been connected correctly. Refer to Page 3 of this instruction manual.
Important
Before the amplifier is switched on, (switch \), the power output of the drive radio should be adjusted correctly if it is capable of outputting a power greater than 10W. This may be done with the amplifier connected but switched off. 10W is the maximum per-missible input power to the amplifier and an input power of 1-10W is OK as it is not necessary to run the amplifier at full output if not required. Generally 7W input should be sufficient. When the amplifier is switched on LED ` is illuminated. The amplifier does not have protection against excessive input power and as such the responsibility will be with the user not to overdrive it. Maximum input should not exceed 10W. The best performance of the amplifier will be obtained if the amplifier is operated at just less than full output which should be achieved with about 7W input on the 10m band. If the drive radio cannot be reduced below 10W then the input attenuator should not be used to lower the input to the amplifier. The input attenuator can and should only be used to reduce the output of the amplifier if required. There are 5 levels of attenuation, with position 6 being direct input. Damage will occur if the amplifier is operated above 10W input power. When the amplifier is in transmission LED a is illuminated. When it is OFF the ampli-fier is in receive state.

Antenna Considerations:
The amplifier is designed to work into a 50 ohms resistive load and any antenna outside of this requirement must use an antenna tuning unit between the output of the amplifier and antenna.
It is recommended to check that the antenna to be used is sufficiently rated for at least 500W power handling before connecting this product. It is also recommended to check that the VSWR does not change considerably with increased power as this would indicate that the antenna was not suitable for high power use.
Cable losses particularly increase with increasing frequency. Always use a good quality 50 Ohm feeder and keep the length as short as possible. Not only will this allow more power to reach the antenna but will also increase the signal strength at the receiver.
This amplifier should not be operated into mismatched loads, (high VSWR), An accept-able level should be less than 1.5:1. Less than 2.0:1 is also acceptable but some reduction in power may be seen and the amplifier will work less efficiently and generate more heat. There is no protection for excessive VSWR so it is advised that the antenna is tuned cor-rectly for the frequency it is to used on to avoid damage to the amplifier.

Mode

The KL505 may be used for all of the common narrow band transmission modes such as SSB, CW,AM,FM, SSTV and data modes etc.
RX Preamplifier:
The KL505 is fitted with an RX preamplifier, that when activated can help to increase the received signal level. This can be used when the signal level is low to help improve the intelligibility of the received signal. The RX preamp can be used independently of the amplifier however when the amplifier and preamp are both activated the preamp is auto- matically switched out of line when the amplifier is in transmission. Switch [is used to switch the preamp on and off. LED _ is illuminated when the preamp is switched on.
Warning: Transmit Time.
Hi Duty cycle modes such as FM and Data modes etc. operate the amplifier at full power all of the time unlike modes like SSB and CW that are either intermittent or only reach peak output for very short times, these high duty cycle modes will run the amplifier much harder and generate more heat in the same amount of time. It should be noted that the amplifier although capable of being used with these modes should not be operated con-tinuously. A transmission time of more than a few minutes should be avoided to avoid excessive transistor junction temperature. The exact time for transmission in these modes will depend on numerous factors such as, how good the ventilation around the amplifier is if there is sufficient space for freely flowing air to circulate, etc. If the ambient tem-perature is high this will reduce the total time in transmission. Common sense should be exercised, if the heat sink is becoming too hot then sufficient time should be allowed to let it cool down before reuse.

Input drive and power output:
The amplifier should give full output with approximately 7W input. Excessive input power should be avoided and the amplifier should always be operated in a responsible manner.
The KL505 features an input attenuator ] that may be used to reduce the output of the amplifier if the drive radio does not have the facility to reduce its output power.
The input attenuator should NOT however be used to reduce the input power level of the drive radio if it is greater than 10W! Otherwise the attenuator may be damaged from overheating. There are 5 levels of input attenuation and position 6 is direct input, with no attenuation. So setting to position 1 will provide the lowest output power from the ampli-fier, and position 6 the maximum output.
Maximum output power considerations:
All amplifiers have a maximum output and this occurs shortly after gain compression where by Pin no longer produces a proportionate increase in power output . The amplifier should always be operated at a point below its saturated output. Trying to extract every last watt by overdriving the amplifier will not actually help your signal to be stronger, you will in fact cause higher levels of distortion which will make your signal less intelli- gible at the distant receiver station. Running the amplifier a little under max output will also allow the amplifier to run cooler and make it more reliable for many years of use. As an example consider the following situation. 1 ‘S’ point on a receiver is usually approximately calibrated at 6dB so for example the difference between S5 and S7 2 ‘S’ points is 12dB. The difference between 10W and 200W is about 13dB a healthy increase to your signal strength, 2 ‘S’ points, with the same antenna. Now lets say for example you run the am-plifier at a moderate 200W output by slightly reducing the input power, the difference between 230W and 200W is 0.6dB which when you compare this to 6 dB per S point is actually very little and as the amplifier is not running at its absolute maximum will give a cleaner output with less distortion that will actually make a difference at the distant receiver for the better!!RM ITALY-KL505-HF-10m-Linear-Amplifier-
FIG-3

KL505 Broadband use

The KL505 is designed for operation on the 10m Amateur radio band, from 28.000MHz to 29.700MHz however the amplifer has useful gain covering all of the bands from 160m to 10m, (See the diagram ‘Gain vs Frequency’ on the previous page). The amplifier does not feature Low Pass Filtering so it is essential if the amplifer is used on other HF bands that a suitable Low Pass Filter is connected to the output in order to supress the harmonic output of the band being used, to avoid unneccesary interference and comply with current regulations which should be know to the operator before use. It should be noted that the gain of the amplifer increases somewhat on the lower bands so less input power is required for the same level of output power. Input drive should be adjusted accordingly in order not to overdrive the amplifier, the input attenuator ] may also be used to adjust the drive level so long as the input to the amplifer does not exceed 10W. We reccomend that the amplifer be driven with about 7W from the exciter or optimum performance on the 10m band.

KL505 Schematic

RM ITALY-KL505-HF-10m-Linear-Amplifier-
FIG-4 RM ITALY-KL505-HF-10m-Linear-Amplifier-
FIG-5

  • tel +39 0534 60460

  • Costruzioni Elettroniche fax +39 0534 60463

  • rm@rmitaly.com

  • KL 500 rel. 6.0

Attention:

The use of Linear Amplifiers are controlled by specific laws within the country of use. These laws must be known to the user and are entirely the responsibility of the user. The manufacturer declines any responsibility from unlawful use.

Warranty

This product is covered by a 24 month warranty commencing from the date of purchase. The original purchase receipt will be required for any claim. This warranty does not cover aesthetic damage or damage to the RF power transistors from incorrect use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals