LC Lenercom 150PSI Car Jump Starter with Air Compressor User Guide

Jump Starter & Air Pump
QUICK USER GUIDE

Intended Use

The Lenercom 4-in-1 Jump starter is a portable device equipped with a battery and jumper cables. The Jump starter has an internal battery that can deliver a lot of current at one time to start a vehicle battery. This gives your car, truck, motorcycle, or boat  battery a shock, which makes this battery come back to life. This Jump starter can also serve as a powerbank, flashlight, SOS emergency light, and compressor.
There are no other uses for this product.
Only use this product as described in user manual. Any other use is considered improper and may result in personal injury or material damage, is not liable for damage or injury resulting from improper or careless use.

Safety During Unpacking

Do not leave packaging material or accessories lying around carelessly during unpacking. lt may become dangerous playing material for children. Do not dispose of the packing materials until the Jump starter has been tried and is working.
WARNING: Small parts
Contains small parts not, for children under 3 years or any individuals who tend to place inedible objects in their mouths.
Small parts can be swallowed or lodged in the windpipe and creafe a choking hazard, As a general guide, a choking hazard is anything with small parts that are less than 31mm in diameter and 57mm long.

Instructions for Emergency Start/Overstart

Preparation.

• Make sure that the Jump starter has more than 30% power. When less than 30% do not use it to jump start a vehicle.
• Do not connect the device fo a vehicle battery with a voltage >12V.
• Remove the vehicle key from the ignition.

Connect the Jump starter.
Connect the black jumper cable connector to the Jump starter, makingsure the connector is fully seated in the Jump starter. The connector’s LED flashes red and green when the connection is successful.

Connect the battery.
The red wire is positive (+) and th black wire is negative (-). Connect the red clamp to the positive (+) terminal of the car battery and the black clamp to the negative (-) terminal of the battery.
If the connection is successful, the LED turns green.

NOTES:

• If the battery of the vehicle is an old battery, the oxidation layer must be removed before using this product.
• Be sure to adjust your clamp for maximum contact for both sides of the clamp. Always check if the clamps are well connected.
• When using the clamps, do not allow the positive and negative poles to contact each other. This may cause sparking and result in a safety hazard and cause a short circuit of the Jump starter.

Start the car.
Put the vehicle key back into the ignition and start the car.

Disconnect the jumper cables.

• When the vehicle is started, remove first the jumper cables from the Jump starter and then remove the red and black clamps from the vehicle battery.
• Leave the vehicle’s engine running for a while.
• After jump-starting a vehicle, it is recommended to recharge the jump starter before reuse.

The car still won’t start?
Option 1:
Make sure the connector of the jump cables is connected with the jump starter and the clamps are disconnected from the baffery terminals.
Press “RST” on the back of the connector until the LED turns green(use a small pointed object to press the button). Connect the red clamp fo the positive (+) terminal of the battery and the black clamp to the negative (-) terminal of the battery.
Now start the car.

Option 2:
Disconnect the negative (-) ground cable from the battery.
Start again with option 1 (now the negative (-) ground cable is disconnected from the battery).
Now the car without battery will only start on the Jump starter.

Compressor Operation

Applications
The product can be used for most vehicles with inflatable wheels (except trucks > 5 tons). The compressor can be used for manual or automatic inflation. Four different units of pressure can be selected for ease of use. ln addition, the product can be used as a  pressure gauge.
This product comes with 4 preset modes. Once you have selected a mode you can manually adjust the pressure for the application you want. The product will start automatically if this is set.

ON/OFF Button
Press and hold the ON/OFF button for 3 seconds. The LCD screer will display the current battery capacity.
Press and hold the ON/OFF button for 3 seconds to turn off the product. The product will also automatically turn itself off if there is no activity for more than 60 seconds.

MODE Button
This product has 4 preset programs to choose from. The 4 programs are “Car”, “Motorcycle”, “Bicycle” and “Ball”.

Note :
The data of the recommended inflation air pressure range is for reference only. Please refer to the instruction manual of the inflated item for actual use. (The above data comes from the laboratory)
Press once on the MODE button to switch to the correct mode. A preset pressure is selected but you can change it according to the next fable.

UNIT Button
The product offers 4 units of pressure:
-Psi
-bar
-kPa
-Kg/cm2
You can press the UNIT button to switch between the different units. Your choice will then be displayed.

PRESET Buttons
The preset mode includes a preset pressure for your convenience. However, if you want to adjust it, you can do so by pressing the + or – button. Pressing once changes the pressure by 0.1, holding it down changes the pressure quickly. Wait 3 seconds or click on  the UNIT button to keep this value.
Turn on the pump and it will automatically stop at the preset point.

Use for Car/Motorcycle/ElectricScooter/Bicycle

1. Quickly press and tighten the inflator onto the tire valve stem.
2. Turn on the device and the LCD screen will display the current tire pressure.
3. Click on the manual or the preset mode and inflate to the desired pressure.

Use for lnflatable Ball/Floatin Equipment/Airbed

1. Choose the right inflator adapter. Secure if to the valve
2. Turn the unit on, choose from manual or presef mode, and pump up.

Instructions for the Compressor
STEP 1 Connect the air hose.
Connect the air hose. Make sure the air hose is screwed all the way to the compressor.

STEP 2 Connect the air valve.
Push the nozzle onto the valve as far as possible and push the siphon in the opposite direction of the hose.

STEP 3 Inflate the tire.
Turn on the compressor by pressing the ON/OFF button. Press the MODE button to select the desired pressure. If the air pressure needs to be adjusted,you can press the + or – button.
Press the ON/OFF button to start pumping. The compressor stops automatically when the desired pressure is reached.

STEP 4 Disconnect the air hose.
Wait until the pumping has stopped and disconnect the air hose.

WARNING:

• To avoid overinflating the tires, it is advisable to consult the fire pressure values in the car manual before inflafing the tires or consult the tire markings on your bike.
• Do not kink or block the air hose while the compressor is running. Keep the air hose as straight as possible.
• The compressor is designed for occasional use. Prolonged use leads to overheating of the product and may cause damage. Cooling for 5 minutes after inflating a tire is recommended.
• If you find abnormal noises or excessive temperature during inflation, stop using the compressor immediately. Let the appliance cool down for at least 15 minutes.
• The air hose may be hot after use. Be careful with your hands when removing the air hose.
• The connector between the air hose and the connection to the compressor may become hot during prolonged use. Always wait a few minutes before touching the connector.

LED Light Function

The product has a built-in LED flashlight for when it is dark.

1. Turn on the device and then press the LED LIGHT buffon for 3 seconds. The lamp will now turn on.
2. Press the LED LIGHT button again to enable the S.O.S. mode.
3. Press the LED LIGHT button again to turn on the flasher.
4. A long press on the LED LIGHT button turns off the LED.

Powerbank Function

This product has a Q3.0 18W USB output to charge your partable devices. With a battery capacity of 12000mAh,you have more than enough power to charge your devices. To use this function, you need to charge the product in advance.

Charging the Battery

WARNINGS:
-Charge the battery of the Jump starter fully before you use it for the first time or after a long period of disuse.
-To extend the life of your battery, drain if every 3 months and then give it a full charge.
-Always follow the safety instruction as described in the chapter”Safety Instructions – Battery Safety”.

• Ensure that the device is switched off.
• Attach the supplied USB cable to the USB-C port of the jump starter and plug the other end of the charging cable into a 5V/2A USB adapter (not included). We recommend using a USB adapter, however, using the USB interface of a computer/laptop or a  powerbank is also possible (but not recommended).
  -To shorten the charging time, the 5V/2A USB adapter is the best choice.
  -Some USB outlets might have insufficient outpuf current, which will slow down the charging speed or even hinder the charging.
  -Charging from an empty battery to a full battery with a 5V/2A USB adapter takes 6 hours.
• When the device is charging, the charging indicator light flashes.
• When the battery is fully charged (at 100%), the charging indicator light stops flashing,
• Unplug the USB cable when the charging is finished to avoid overcharging and damage.

Safety Instructions

READ the user instructions carefully , and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property.  Such cases will invalidate the warranty.
Electrical devices and batteries can expose people, especially children, to hazards that can cause serious injury or death. The use of electrical devices and batteries can present hazards including, but not limited to, injury, fire, electric shock, and damage to the  electrical system. These safety instructions are intended to give you the information you need to use the Jump starter and avoid such hazards. Common sense and respect for the device will help reduce the risk of injury.
All possible hazards cannot be covered here, but we have tried to highlight some of the important ones. Also, observe the warnings or safety instructions in the individual chapters of this manual.

General Device Safety

• Do not use the jump starter for any other purpose other than its intended use (see the chapter “Intended Use”).
• The Jump starter is designed and intended for private use and is not suifable for commercial or industrial use.
• The jump starter is meant for indoor use, but can also be used outdoors in dry weather conditions (the device is not waterproof). lt is recommended to keep the device out of direct sunlight for extended periods when used outdoors. The device must be  returned indoors after use.
• Hande the device carefully. Jolts, impacts, or a fall even from a low height can damage the device.
• Do not place the jump starter on any unstable surface. This may result in falling and cause malfunction.
• Do not place the jump starter under mechanical stress.
• All parts must be correctly assembled to ensure the safety of the device.
• The device needs to be properly and securely connected (during use and charging). Follow the instructions to prevent any possible damage/injury.
• Never use accessories not recommended by the manufacfurer. They can pose a danger to the user and damage the device.
• Never drop or insert any object or fingers into any opening.
• Do not apply excessive force when using the buttons on the jump starter.
• Do not apply excessive force on the display and do not touch the display with sharp objects.
• Do not leave the switched-on Jump starter unattended. Close supervision is necessary when used near small children.
• Keep bystanders away when you want to jump-start a vehicle battery. Children, onlookers, and passers-by must be restricted from entering the work area for their protection.
• lf it is no longer possible to operate the Jump starter safely, take it out of operation and protect it from any accidental use. A safe operation can no longer be guaranteed if the device:
  -is visibly damaged,
  -is no longer working properly，
  -has been stored for extended periods in poor ambient conditions or
  -has been subjected to serious transport-related stresses.

Persons & Use

• The Jumpstarter is not a toy. Keep and store it out of the reach of small children. Never put the  air hose in the ears, noses, or mouth of anyone or an animal.
• Keep small children and animals at a safe distance when using the Jumpstarter.
• The device may only be used by adults.
• This device is not intended for use by persons with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the device by a person responsible for  their safety.
• Never use the device if you feel sleepy or if you have taken substances that shorten your reacion time (such as painkillers or alcohol).
• Be permanently alert. Pay attention to what you are doing. Proceed wisely. Do not use the Jump starter if you are not focused.

Electronics & USB Adapter

• You may not reconstruct, self-repair, or disassemble the Jump starter. This can damage the device.

• Maintenance, modifications, and repairs may only be carried out by the manufacturer, a professional workshop appointed by the manufacturer, or a similarly qualified person.

• Check the device from time to time for damage. Never use the device if it shows signs of damage.

• The jumpstarter cannot be used as a charger for a vehicle battery.

• Do not jump start a vehicle while charging the Jump starter.

• Do not charge the Jumpstarter immediately after use or while it is still hot. Let it cool down first.

• Only use a USB adapter 5V / 2A output (not included in the package) to charge the Jump starter.
  Another adapter with the wrong specifications may cause malfunction and/or damage. Charging with a power bank or using a USB port of a laptop/computer is allowed, but not recommended.

• To prevent damage to the adapter and/or the Jump starter make sure your power mains socket supplies the correct power supply for the USB adapter.

• The mains socket must be located near the device and easily accessible.

• To avoid energy loss and possible safety risks, always remove the USB adapter from the mains socket when the battery is not being charged and before cleaning.

• Never force the plug of your USB adapter into a mains socket; if it does not fit easily into the mains socket, stop using it. Always make sure that the plug of your USB adapter is properly connected fo the mains socket.

• It is normal for the USB adapter to feel a little warm; however, a loose fit between the mains socket and the plug of the USB adapter can cause overheating and deformation of the plug.
  Contact a qualified electrician to replace the loose or worn mains socket.

• To disconnect the USB adapter, grasp the adapter housing and pull the adapter out of the mains socket.

• If the power fails during the charging, turn off the device immediately and pull the USB adapter from the mains socket.

• If smoke is produced, or there are any unusual sounds or smells, switch off the jump starter immediately and remove the mains plug from the mains socket. ln these cases, fhe jump starter should not be used until it has been inspected by the manufacturer,  or a similarly qualified person. Never inhale smoke from a potential device fire. lf you have inhaled smoke, consult a doctor. The inhalation of smoke can be harmful.

• For safety reasons, always disconnect the USB adapter in the event of a thunderstorm.

USB cable &jumper Cables

• Do not modify the cables.
• Check the cables periodically for damage. Never use a cable if there are any signs of damage.
• Do not touch a jumper cable if it is damaged. A damaged cable can cause a deadly electric shock.
• To prevent risks, damaged jumper cables may only be replaced by the manufacturer, a professional workshop appointed by the manufacturer, or a similarly qualified person.
• Never force a connector into a USB port. lf the connector and port don’t come together easily, they probably don’t match. Check for obstructions and make sure the connector matches the port and that you have correctly positioned the connector with the  port.
• Never unplug the USB cable from the adapter or the Jumpstarter by pulling the cable. Always pull on the USB connector.
• Be careful not to trip over a cable.
• The cables must not be kinked, pinched, or twisted.
• Make sure that the cables are not squeezed, bent, damaged by sharp edges, or put under mechanical stress.
• Never tie a knot in a cable and do not tie cables together.
• Avoid excessive thermal stress on the cables due to extreme heat or cold.
• Children may get entangled when playing with a cable (danger of strangulation). Electric cables are not toys.

Heat & Cooling

• The Jumpstarter may become warm during operation or while charging. This is normal.
• Do not cover the device while it is in operation or being charged as this may cause the Jumpstarter to overheat. This poses a risk of fire, electric shock, or injury.
• Make sure that the ventilation around the device is good during charging.
• Keep the device away from heat sources and away from areas where the ambient temperature is relatively high (e.g. stoves or other heat sources). Never use the device near naked flames(such as burning candles) or on hot surfaces.
• The Jumpstarter is designed to work best in normal ambient temperatures between 0°C and 35°C and to be stored at temperatures between 0°C and 45°C. The Jumpstarter may be damaged and the battery life may be shortened if the device is stored or  used outside this temperature range. Do not subject your device to dramatic changes in temperature. Do not store your device in a hot car or direct sunlight for extended periods. Do not place the device near a window (especially in the summer).

Water
WARNING: This device is not waterproof!

• Never use the jumpstarter with damp or wet hands. Moisture can cause electric shock or short circuits.
• Do not use the Jumpstarter in or near a bath, shower, swimming pool, or any container filled with water, such as a sink.
• Do nof charge in wet or damp environments (such as the bathroom).
• Do nof use in wet environments and do not immerse in liquid. Never pour liquids over or near the Jumpstarter. There is a risk of electric shock/short circuit! If liquid does get into the housing unplug it immediately and then turn off the Jumpstarter.
• Do not reach for the device if if has fallen info fhe water during charging. lmmediately unplug it from the mains socket and only then remove it from the water.
• Make sure the device is standing/placed or lying on a dry surface.

Battery Safety

• Do not place the jumpstarter near a fire, or in direct sunlight. The heating of the device can cause additional heating, breaking, or ignition of the battery.

• Avoid charging the battery at temperatures below 5°C or above 40°C.

• Do not continue charging the battery if it does not recharge within the specified charging time.
  Doing so may cause the battery to become hot, rupture, or ignite. Unplug the device once fully charged or if left unattended during charging.

• Do not attempt to recharge the battery if the battery emits any substances. In that case, immediately distance yourself from the battery in case of fire or explosion. Only recharge with a suitable charger.

• Do not recharge the battery near flammable materials (fire hazard).

• Do not attempt to modify, disassemble or change the battery.

• Do not use your Jumpstarter if the battery begins to emit odor, starts to overheat, or begins to leak.

• Do not touch any leaking materials or breathe fumes emitted from the battery. Leaking or damaged batteries can lead to caustic burning of the skin. Therefore, use suitable protective gloves.

• The battery contains dangerous substances, do not open the battery or insert anything into an exposed battery.

• Do not allow children and animals to touch an exposed battery.

• Never throw the battery into a fire.

• Do not short-circuit the battery. The battery can explode or leak if shorted,

• An empty battery can still be dangerous.

• Keep the battery away from children, babies, or animals.

Safety During Use

1. Preparation
   . Check that the voltage of the vehicle battery matches that of the Jumpstarter.
   . Clean the battery terminals before, connecting them to the jumpstarter. Do not allow corrosion to come into contact with the eyes.
   . Do not place the Jumpstarter in the engine compartment or near the battery. Place the device as far away as the jumper cables allow.

2. Protect yourself
   . Consider having someone close enough or within range of your voice to assist you when working near a vehicle battery.
   . Under extreme conditions, battery leakage of the vehicle may occur. Carefully wipe the liquid off using a cloth & avoid skin contact.
   . Always have protective eyewear when using this product, contact with battery acid may cause blindness and/or severe burns. Be aware of first aid procedures in case of accidental contact with battery acid.
   . Have plenty of fresh water and soap nearby in case battery acid contacts the skin. lf battery acid comes in contact with the skin, rinse immediately with water, and then wash thoroughly with soap and water. If redness, pain, or irritation occurs, seek  immediate medical attention.
   . Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a vehicle battery. A vehicle battery can produce a short circuit current high enough to weld a ring, or the like of a metal, causing a severe burn.
   . Never allow battery acid to come in contact with the Jumpstarter.

3. Supported battery types
   . With the Jumpstarter, you can jump-start all 12-volt AGM (with electrolyte absorbent glass mat), GEL (with gelifi electrolyte), and lead-acid batteries.
   . The jumpstarter is not suitable for use with electric vehicles with a built- in rechargeable battery.
   . Do not use the Jump starter on a damaged or frozen battery!

4. First aid

WARNING: Danger of chemical burns!
-Protect your eyes and skin against corrosion from acids when coming into contact with the baffery.
-Use acid-proof goggles, clothing, and gloves.
lf battery acid contacts skin or clothing, wash immediafely with soap and water for at least 10 minutes and get medical attention immediately.
If battery acid comes in contact with your eyes, flush your eyes immediately, for a minimum of 15 minutes, and seek immediate medical attention.

Explosion Hazard
Do not operate the Jumpstarter in explosive atmospheres(including gas stations) and in the presence of flammable liquids, gases, or dust.
Ensure the positive terminal clamp does not come into contact with fuel lines (e.g. petrol pipe)!

Warranty & Liability

Lenercom guarantees that for one year from the date of purchase, this product will be free from defects in materials and workmanship. This warranty applies to products used for personal purposes, and not for commercial or rental purposes. Lenercom, at its  discretion, will replace or repair this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or refurbished product or component. If the product is no longer available, a replacement may  be made with a similar product of equal or greater value, no refunds shall be given. This is your exclusive warranty. Your replacement unit will be returned to you for no charge and will be covered under this warranty for the balance of the warranty period.  This  warranty is valid for the original purchaser from the date of initial purchase and is not transferrable. Proof of purchase is required to obtain support under the warranty.

This warranty does not cover:

• negligent use or misuse of the product;
• use or charging with an incorrect voltage or current;
• water damage;
• use contrary to the operating instructions;
• disassembly, repair, or modification by anyone other than Lenercom
• damage caused by accidents or disasters, such as fire, flood, earthquake, war, vandalism, or theft;
• change of color that might happen over time;
• normal wear and tear.

Damage caused by failure to observe this manual will void the warranty. We do not accept any liability for consequential damage! We accept no liability for material damage or personal injury caused by improper use or failure to observe the safety instructions.  In such cases, the warranty becomes void.

Trouble Shooting

2.Check for air leaks in the trachea.
3.Check whether the connecting parts at both ends of the trachea are tightly installed.
4.Check whether the tires are flat.
Has been turned on, but cannot be inflated| 1.Check whether the battery power is sufficient.
2.Check whether the air pressure of the inflated item is higher than the preset value.
The inflation is normal, but the display pressure value is zero| Low-pressure inflated objects such as balloons are not within the  measurable range of this device.
After installing the gas nozzle tightly, the  power has been automatically turned off| It will automatically shut down if there is no operation within 30 seconds,  just restart it.
There is air leakage when connecting the  trachea| Install the trachea tightly.

Lenercom reserves the right to make changes at any time, without notice or obligation, in the user manual, colors, specifications, accessories, materials, and models.
All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, without the prior written permission of the publisher,  except in the case of brief quotations embodied in critical reviews and certain other noncommercial uses permitted by copyright law.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>