ubbink MultiBrigh 20 LEDs User Manual
- June 8, 2024
- ubbink
Table of Contents
www.ubbinkngarden.com
MultiBrigh 20 LEDs
User Manual
MultiBrigh 20 LEDs
| MultiBright 3 x 10| MultiBright 20| MultiBright 20 LEDs| MultiBright 35
---|---|---|---|---
Art. no. EU| 1354055| 1321872| 1354037| 1321874
Art. no. UK| 1354555| 1321572| 1354537| 1321574
| 230 VAC /50 Hz| 230 VAC / 50 Hz| 230 VAC / 50 Hz| 230 VAC / 50 Hz
| 230 VAC /12 VAC 36 VA, IP X4| 230 VAC/ 12 VAC 20 VA, IP X4| 230 VAC/ 12 VAC
12 VA, IP X4| 230 VAC/ 12 VAC 36 VA, IP X4
| Halogen MR 11, 10 watt| Halogen MR 16 20 watt| LED MR 16 20 LEDs| Halogen MR
16 35 watt
| Halogen MR 11, 5 watt| Halogen MR 16 20 watt| LED MR 16 20 LEDs| Halogen MR
16 35 watt
| 3 x 5 m| 5m| 10m| 5 m
| max. 1 m| max. 1 m| max. 1 m| max. 1 m
| | | |
MultiBright 3 x 10 / 20 /20 LEDs / 35
Underwater fl oodlight
MultiBright 3 x 10 and 20 LEDs can be employed both in your pond and its
environment, for lighting your water ornaments.
MultiBright 20 and MultiBright 35 should be employed as underwater fl oodlights
only.
Please read carefully through the directions for use before you put the device
into operation.
Directions for use
During the installation or dismantling of the device, as well as during its
maintenance, the power supply must be always be disconnected.
Do not connect the MultiBright lighting when the power supply does not
correspond to the product specifi cations. Where appropriate, fi nd out about
the connection specifi cations from your power provider locally. The
MultiBright lighting must be connected at a socket outlet with grounding
contact, whose electric circuit includes a ground fault switch (Fi –
protective switch / 30mA). You can obtain further information from your
electrical specialist locally. For MultiBright, always employ a safety
isolating transformer for exterior areas (IP X4). The plug socket for the
transformer should be at least 3.5 meters distance from the pond. The power
cable cannot be replaced. If the cable is damaged, the device cannot be
employed any longer.
CAUTION! In case of the utilization of the MultiBright 3 outside of the
pond, please use the delivered 5 W lamp instead of the 10 W lamp, in order to
avoid overheating.
**Installation
**
MultiBright 3 x 10
You can carry out the installation in diff erent ways:
- Installation on the PE cover plate through bolts in the raw recesses at the edges.
- Screwed attachment of the fl oodlight to the ground fastening pin, which is then inserted into the soil.
MutliBright 20 / 35 / 20 LEDs
With the lamp bracket, MultiBright 20 / 20 LEDs can be attached to the fountain pump. It is also possible to mount the fl oodlight on the ground fastening pin, which is then inserted into the soil.
With the universal installation bracket, you can mount the MultiBright 35 on the pond base or on a platform in the pond.
**** Replacement of the illuminants
-
Pull the plug of the safety isolating transformer from the plug socket.
-
Remove any possible residual water from the fl oodlight surface.
-
1 MultiBright 3 x 10 / 20 / 20 LEDs : Switch off the fl oodlight ring
3. 2 MultiBright 35: Loosen the bolts and remove the fl oodlight covering -
Carefully remove the covering glass from the fl oodlight.
-
Replace the halogen lamp (do not touch with the fi ngers!) and/or LED lamp
-
Dry the glass and the fl oodlight ring carefully and attach both again. Please ensure the correct positioning of the ring gasket in this case!
**Installation of a colored disk (only MultiBright 20 and LED MultiBright
20)**
Screw off the fl oodlight ring and place the colored disk on the covering glass.
Please ensure that the ring gasket is placed on correctly.
Attach the fl oodlight ring again and screw tight by hand.
Cleaning
Please follow the instructions for the replacement of the halogen lamp. Employ
only water and a soft brush. Ensure no liquid penetrates the fl oodlight.
Repairs
If cable, housing or transformer are damaged, no repair is possible. You may
no longer employ the aff ected part and you must dispose of it.
Guarantee
We grant you a guarantee of 2 years on this product against verifi able material and manufacturing faults, which applies from purchase date. To make a guarantee claim, the original purchase receipt must be submitted as a verifi cation of purchase. Not covered by the guarantee are illuminants, as well as all complaints whose cause can be attributed to installation and operational faults, lack of maintenance, frost action, incorrect repair investigation, power application, external faults, overload, mechanical damage or the action of foreign bodies. Also excluded from the guarantee are all complaints regarding part damage and/or problems, whose causes can be attributed to wear.
Environmental protection
Old electrical devices should not be disposed of in domestic waste. Please
bring the old device to your local turn-in center. You can obtain further
information from your dealer or refuse collecting company.
Conformity Declaration
The company UBBINK GARDEN BV, having signed below, declares of their own responsibility that the safety transformer, part of the delivery volume, meets the requirements of the European Directives 73/23/EWG (Low voltage directive) and 89/336/EWG (Electromagnetic compatibility). The following harmonised standards have been applied:
EN 61558-2-6:997, EN 61558-1/A11:2003,
EN 61000-3-2 :1995/A14:2000, EN 61000-3-3:995/A1:2001,
EN 55014-1 :2000/A1 :2001, EN 55014-4-2 :1997/A1 :2001
Alkmaar, 01-11-2007 Ubbink Garden
Ubbink Gardening UK Ltd.
Apollo House,
Neepsend Lane
Sheffield S3 8AU, England
** 0044-(0)1142-215555
FAX 0044-(0)1142-213444**
Documents / Resources
|
ubbink MultiBrigh 20
LEDs
[pdf] User Manual
MultiBrigh 20 LEDs, MultiBrigh, MultiBrigh LEDs, 20 LEDs, LEDs
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>