Forsafe YW-AHD0628 AHD 1080P Wireless Rear View Camera System Instruction Manual

Forsafe YW-AHD0628 AHD 1080P Wireless Rear View Camera System

Package contents

• Wireless camera x 1
• 7″ wireless monitor x 1
• Mount Bracket x 1
• Monitor sunshade x 1
• Antenna x 2
• Screw Kit for Camera Installation x 1
• Camera Power Cable x 1

Before Beginning Installation

Before drilling, please check that no cable or wiring is on the other side of the wall. Please clamp all wires securely to reduce the possibility of them being damaged while vehicle is in use.
Keep all cables away from hot or moving parts and electrical noisy components.
We recommend doing a benchmark test before installation to insure that all components are working properly.
Step 1: Choose the monitor and camera locations.
Step 2: Install all cabels in vehicle, when necessary a 0.8 (20mm) hole should be drilled for passing camera cable through vehicles walls. Install split grommets where applicable.
Step 3 : Once all cables and wiring have been properly routed, perform a system function test by temporarily connecting the system. If the system seems to not be operating properly see troubleshooting.

Installation Guide

Camera Installation

1. Attach the camera bracket close to the rear marker lights, centered on the vehicle.
2. Camera: drill a 20mm (0.8in) diameter hole into the vehicle body near the camera and bracket. Insert camera cable into a vehicle not to kink cable) and fit the grommet into a hole. Apply sealant around the grommet to increase resistance to water penetration. connect the camera to the camera extension cable which runs inside the vehicle.
3. Feed as much cable as possible into vehicle with a clamp securely. This reduces the possibility of cable being hooked or snagged. The aviation camera cable uses aircraft grade connectors which means the camera cable can be exposed to all weather conditions.
4. Attach the camera to the bracket using screws and adjust the angle.
5. The wiring camera connects the POWER (red) to 12V and the GROUND (black).

Monitor

1. To attach the pedestal mount to the dashboard or to the headliner use self-tapping screws and/or the adhesive pad.
2. Attach the monitor to the mount, and adjust the mounting angle to allow optimum driver viewing comfort.

Infrared technology built into camera IRs has activated automatically according to the lighting conditions.
The grid lines function can be turned on/off manually from the menu.
(Note: if connecting power directly to the battery, the camera is always ON and therefore can drain the battery. Therefore it is recommended to connect power to an ignition-switched accessory power source.)

Install the monitor

Installation Diagram

Positioning

Monitor Specifications

FULL AHD Wireless Monitor

• Screen Size 7″ ( diagnal length)
• Technology 2.4GHz Digital Wireless
• Transmission Distance 330ft / 100m
• Frequency 2400 -2483.5 MHz
• Camera Max support 4 cameras
• Resolutio n 1024 x 600 ( RGB)
• Display Forma t 16:9 /500:1
• Display Brightness 400cd/M²
• Viewing Angle U: 50˚ / D: 50˚ / R: 70˚
• Video Source 1Vp-p, 75Ώ
• Power Source DC 12-32V
• Display Mode Single, Split view, Quad view
• Power Consumption < 500mA
• Operating Temperature -30℃ ～ +80℃
• Video System Auto NTSC / PAL
• Overall Dimension 19.5cm (L) x 3cm (D) x13cm (H)
• Weight 0.4kg
• Sync System Internal

Note: this monitor can record video footage

• DVR Storage
  • SD card supports up to 128GB ( up to level 4)
  • SD card is NOT included in the package
• Feature Overview
  • Preview / Recording / Playback

Camera Specification

• Camera Image 1080P
• Type Wireless 2.4GHz
• View Angle 110˚
• Sync System Internal
• Transmission Distance 330ft / 100m
• Infrared distance 50 Feet (18 Infrared IR )
• Illumination 0 Lux ( IR on)
• Power Source DC 12V -32V
• S/N Ratio of more than 48dB
• Electronic Iris 1/50, 160-1/100000S
• Waterproof Rating IP69K
• IR switch control ACDS Automatic Control
• Impact Rating 20G vibration / 100G shock
• Operating Tempt -30℃ ～ +80℃ / RH95% max
• Storage Tempt -40℃ ～ +60℃ / RH95% max
• Dimension 9.9cm (L) x 5.6cm (D) x9.6cm (H)

Monitor Operation

1. Quad view (4 camera) display mode
2. Split view (2 camera) display mode
3. Single view (1 camera ) selection
4. OK: confirm button in sub-menu
5. Power on / off button
6. UP Arrow
7. Menu / Selection button
8. Down arrow

• To turn on the monitor, press the “POWER” button
• To get to the menu, press ” MENU” and use the arrows to choose your settings.
• To display options, press ” MENU” to select
• To confirm your choice press “MENU” as confirmed

Main Menu

1. Camera settings: normal / mirror; color; parking line on/off
2. Pairing: to repair camera and monitor or add a camera
3. Record: to set up recording time; format card
4. Playback: to play recording footage
5. View mode: to select quad view; split view mode; auto display 1 to 4 camera on/off
6. Setting : to setup delay time, date/time; display camera selection

How to set up camera

• Press the “MENU” button
• Press the “OK” button
• Press ” +” or “-“ scroll to setup camera FLIP / MIRROR image; Color; Parking Line on/off
• Press the ” OK” button to confirm the settings

Camera Pairing

• This system is default being paired, it displays the camera image as soon as the power connection is finished.
• Camera pairing is needed use when you need to repair the camera and monitor if it loses signals or when you need to add more cameras to this system.
• Press ” Menu”, press “+” or ” – “ scroll to Pairing
• Press “OK” , and it appears countdown “20 seconds” on the monitor
• Press ” Pair” button > 3s in the back of camera
• The monitor displays the camera image when pairing complete

Record

This monitor has a built-in DVR, it can record video footage if you like to.
Note: SD card supports up to 128GB ( up level 4) SD card is NOT included in the package

• Press the ” Menu” button
• Press ” +” or “-“ scroll to “ Record”
• Press “OK”
• Press the ” +” or “-“ scroll to set up record time ( can setup 1-5 mins for one footage to save)
• Or Format SD card when you need

How to set up Record on/off

When you use one camera mode, press ” MENU” > 2S to turn on Record Press ” MENU” > 2S again to turn off Record

How to playback the recordings saved

• Press the ” Menu” button
• Press ” +” or “-“ scroll to “ PLAYBACK”
• Press “OK”
• Press “ +” or “-“ to scroll to the footage you want to playback
• Press ” OK” , playback starts

How to choose the display view mode

• Press the ” Menu” button
• Press ” +” or “-“ to scroll to “ View mode”
• Choose desired view mode when you have two or more cameras installed, Press “OK”

If you hope to see each camera in loop viewing automatically, choose and ” SCAN” appears on the screen in this mode

Troubleshooting

• Monitor Displays Blue Screen & Displays No Signal
  Do a hard reset, unplug all cables and power cables and leave them out for 2 minutes and then re-connect them.
  Check to ensure that the connection to the camera is tight.

• The monitor Will Not Power-Up ( no backlight no power button )
  Check fuse
  Check 12v+ to monitor

• No Image On Screen
  Verify the camera is connected to antenna
  Verify camera is connected to the cable

FCC Caution

§ 15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

§ 15.21 Information to user.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>