ExBrite WSHDRMMR0028 24 Inch W x 36 Inch H Rectangular Frameless User Manual

ExBrite WSHDRMMR0028 24 Inch W x 36 Inch H Rectangular Frameless

Installation and Operating Manual

WARNING AND SAFETY INSTRUCTIONS

Before assembling your LED Lighted Mirror fixture, please make sure that you carefully read through this instruction sheet, refer back to them during installation to ensure your product is fitted safely and correctly. Keep these instructions for future use.

WARNING Risk of Fire and Electric Shock

• All fittings must be installed in accordance with current IEE wiring regulations. If in doubt, consult a qualified electrician.
• Switch off the electrical supply at the main circuit board BEFORE installation and maintenance.
• Suitable for indoor use only. This product should be positioned well away from curtains and fabrics. Never cover the mirror.
• Regularly check the cord, the transformer and all other parts for damage. If any part is damaged the product should not be used.

INSTALLATION SAFETY

• Inspect the product immediately upon receipt for the transit damage or missing parts.
  Handle the product with care and protect against knocks to all sides and edges of the glass.

• Ensure there are no hidden pipes or cables in the wall before drilling.

• Wear suitable eye protection when drilling. Take care if drilling on tiled surfaces in case the drill slips.

CAUTION
The light source of this product is non-changeable light diodes (LED). Do not disassemble the product, as the light diodes can cause damage to the eyes.

NOTE: The important safeguards and instructions that appear in this manual are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution and care, are factors that can’t be built into any product. These factors must be supplied by the person(s) caring for and operating the fixture. Do not install this fixture in hazardous locations.

CHECK PRODUCT LIST AFTER OPENING THE PACKAGE

• LED Lighted Mirror –1pce
• Screw –2pcs
• Expansion Tube –2pcs
• Installation Manual –1pce
• Returning Guide –1pce
• Extended warranty form –1pce

INSTALLATION

1. Level  and mark the location.
2. Measure the center of the holes and mark the drilling locations ensure marking are leveled.
3. Using a drill, make holes and fill with supplied plugs and screws. Leave a gap of 2 – 3mm between the head of the screw and the wall.
4. We provide plug with mirrors.
   • Optional to cut the plug directly and connect to electrical wiring if using wall switch.
5. Place the mirror against the wall and slide down as shown in image B.

OPERATION INSTRUCTION

ON/OFF Function

• Short press (< 1 second) the LED light switch button to turn on / off the LED lamp.

Dimmer Function

• Long press (> 1 second) the button to adjust the brightness. When the LED is on, long press the button to activate dimming.
  The LED brightness changes in loop from 100% to 5%, or from 5%to 100% on second press.

• To adjust brightness until the brightness meets your requirement.

Anti-Fog Function

• Defog button: Short press the button to activate defogger.
• Note: A short voice of puff is noticed when pressing the button each time. It is normal.

Color temperature Function

• Color temperature switch button: Short press the button to change the color temperature ranged from 3000K to 6000K and with a change order: 3000K→4000K→6000K→3000K. This function required to work under the LED lamp turn on.

Night Light

(For mirror with night light function only)

• DO NOT cover the sensor on top of the mirror.
• Night light will be auto-on/off according to the brightness surrounding.
• Optional to stop night light function by tapping the ON/OFF switch at the bottom corner of the mirror.

AFTERCARE INSTRUCTIONS

Clean using a soft dry cloth only when turned off. Never use cleaning agents or abrasive materials.
Do not allow moisture to come into contact with lamp.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>