ExBrite Frameless WallMounted LED Light Bathroom Mirror Instruction Manual
- June 4, 2024
- ExBrite
Table of Contents
Frameless WallMounted LED Light Bathroom Mirror
Instruction Manual
Installation and Operating Manual
The clock version
The standard version
**WARNING AND SAFETY INSTRUCTIONS
**
Please make sure that you carefully read through this instruction sheet and
refer back to them during installation to ensure your product is fitted safely
and correctly before installing your LED Lighted Mirror fixture. Keep these
instructions for future use.
WARNING Risk of Fire and Electric Shock
- All fittings must be installed in accordance with current IEE wiring regulations. If in doubt, consult a qualified electrician.
- Switch off the electrical supply at the main circuit board BEFORE installation and maintenance.
- Suitable for indoor use only. This product should be positioned well away from curtains and fabrics. Never cover the mirror.
- Regularly check the cord, the transformer, and all other parts for damage. If any part is damaged the product should not be used.
INSTALLATION SAFETY
- Inspect the product immediately upon receipt for transit damage or missing parts. Handle the product with care and protect against knocks to all sides and edges of the glass.
- Ensure there are no hidden pipes or cables in the wall before drilling.
- Wear suitable eye protection when drilling. Take care of drilling on tiled surfaces in case the drill slips.
CAUTION
The light source of this product is non‐changeable light diodes (LED). Do not
disassemble the product, as the light diodes can cause damage to the eyes.
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations that may
occur. It must be understood that common sense, caution, and care, are factors
that can’t be built into any product. These factors must be supplied by the
person(s) caring for and operating the fixture. Do not install this fixture in
hazardous locations.
CHECK THE PRODUCT LIST AFTER OPENING THE PACKAGE
● LED Lighted Mirror | ‐‐1 | pcs | ● Screws for wall | ‐‐3~6 | pcs |
---|---|---|---|---|---|
● Mounting bar | ‐‐1 | pcs | ● Type A Plastic Anchor | ‐‐3~6 | pcs |
● Installation Manual | ‐‐1 | pcs | ● Type B Plastic Anchor | ‐‐3~6 | pcs |
TOOLS YOU MAY NEED
INSTALLATION MANUAL
1 Level and mark the location (vertically hanging and horizontally hanging)
Notes:| 1. Fix the mounting bar into the wall firstly with the distance
as above drawing;
2. For the mirror with the ON/OFF button on the right bottom side, we have a
special design to hang the mirror either vertically or horizontally;
3. The distance between each 2 hanging holes is 7⅞ inch.
2 Place the mounting bar
against the wall and make some marks on the wall|
3 Drill the holes and place the suitable plastic anchors
4 Screw the mounting bar onto the wall with the screw| 5 Connect the mirror
to the main supply.
● We provide plugs with mirrors.
● Optional to cut the plug directly, then connect to electrical wiring if
using the wall switch.
ATTENTION: PLEASE CUT OFF THE MAIN POWER SUPPLY BEFORE WIRING!
6 Hang the mirror onto
the mounting bar (vertically hanging and horizontally hanging)
OPERATION INSTRUCTION
ON/OFF and CCT adjustment
- The button turns blue when connected to the main supply.
- The button is always on as long as connecting to the main supply.
- Short‐touch the button to turn it on/off the mirror.
- Adjusting color temperatures (CCT) between warm white and cool white by long‐touching the button for seconds.
- Finish setting by withdrawing your finger when the color reaches the one you need.
- Optional to be wired to wall switch by ON/OFF memory function.
**Press and hold on for 3‐5 seconds
**
-
Short‐touch the button to turn it on/off the mirror.
-
Long touching the button to adjust the brightness (Dimming).
-
The mirror begins to be warm and defog after pressing the defogger button. Press again to quit the anti‐fog function.
-
Note: The defogger will stop automatically after 60 minutes of continuous operation to prevent any damage caused by prolonged high temperatures.
Clock/Temperature
(This operation is specific to the clock version)
● Turn off the light to set the clock.
● Long touch button 1 or 2 for seconds, and the Hour will flash, then
short‐touch buttons 1 and 2 to set Hour.
● Wait for seconds after setting up the Hour, then it will automatically
switch to the Minute flash.
● Short‐touch buttons 1 and 2 to set up the Minute.
● Wait seconds after you finish the time setting, the time will be saved
automatically.
● The clock shows for 5s, and shifts to the temperature showing for 2s then
goes back to show the clock.|
---|---
● It automatically displays the indoor temperature by auto-sensing through the
temperature sensor.
● DO NOT cover the temperature sensor.
● Night light will be auto‐on/off according to the brightness surrounding when
the rocker switch is kept turned on.
● If need turns off the nightlight at night, please turn off the rocker switch
manually.
AFTERCARE INSTRUCTIONS
Clean using a soft dry cloth only when turned off. Never use cleaning agents
or abrasive materials. Do not allow moisture to come into contact with the
lamp.
THANK YOU FOR YOUR SUPPORT.
We wish you have a wonderful experience with our product. If you have any
other needs or queries, please feel free to contact us by email at
info@exbriteusa.com, and get replies within 48
business hours.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>