Russell Hobbs 26710-56 Blender User Manual

: June 9, 2024
: Russell Hobbs

Table of Contents

26710-56 Blender
IMPORTANT SAFEGUARDS
PARTS
USING YOUR BLENDER
CARE AND MAINTENANCE
BLADE ASSEMBLY
Documents / Resources

26710-56 Blender
User Manual www.russellhobbs.com

26710-56 Blender

Russell Hobbs 26710 56 Blender - FIGURE 1

Read the instructions, keep them safe, pass them on if you pass the appliance on. Remove all packaging before use.

IMPORTANT SAFEGUARDS

Follow basic safety precautions, including:
This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervised/instructed and understand the hazards involved. Children must not use or play with the appliance. Keep the appliance and cable out of reach of children.
To avoid injury, take care when handling the blades, emptying the jug, and cleaning.
****Don’t add hot liquid (over 40°C) as it may be ejected due to sudden steaming.
Misuse of the appliance may cause injury.
Unplug the appliance before assembly, disassembly, or cleaning.
Don’t leave the appliance unattended while plugged in.
If the cable is damaged, it must be replaced by the manufacturer, its service agent, or someone similarly qualified to avoid a hazard.
This appliance must not be connected to a switching device like a timer, or connected to a mains supply that may become interrupted by the electricity provider. This prevents a hazard, which may occur if the thermal cut-out becomes activated for any reason, and is then reset by disconnection of the supply, causing the appliance to reheat once the supply is restored.
Do not immerse in any liquid.

Switch off (O) before fitting the jug to the motor unit.
Don’t use accessories or attachments other than those we supply.
Don’t use the appliance for any purpose other than those described in these instructions.
Don’t operate the appliance if it’s damaged or malfunctions.
Don’t run your blender continuously for more than 2 minutes because it may overheat. After 2 minutes switch off your blender for at least 2 minutes, to allow it to cool down.

HOUSEHOLD USE ONLY

PARTS

Speed control
Motor unit
Blade assembly
Jug
Lid
Cap

BEFORE USING FOR THE FIRST TIME
Turn to “CARE AND MAINTENANCE” and clean the appliance, to remove manufacturing dust, etc.

USING YOUR BLENDER

In use, treat the jug and blade unit as a single unit.

Sit the motor unit on a stable, level surface.
Check that the speed control is set to O.
If required, screw the jug and blade unit together. Tighten firmly.
Lower the jug on to the motor unit with the markings as shown (Fig. A).
Twist the jug as shown (Fig. B) until the markings align.
Remove the lid.
Put the ingredients into the jug. Don’t fill past the 1500 ml mark. If you do, the contents may force the lid off when you start the motor.
Replace the lid. Don’t operate the appliance without fitting the lid.
Put the plug into the power socket.
Turn the speed control to the speed you want (1 = low, 2 = high).
Turn the speed control back to O to turn the motor off.

Generally, large quantities, thick mixes, and a high ratio of solids to liquids require longer timings and slower speeds.
Smaller quantities, thinner mixes, and more liquids than solids require shorter timings and higher speeds.
Setting 2 is more useful for thicker foods.
Turning the speed control anti-clockwise to will give you a short burst at high speed. In this direction, the knob is spring-loaded. When you let go, it’ll return to O.
To add ingredients while the blender is working, remove the cap, pour the new ingredients through the hole, then replace the cap.
Check that the added ingredients don’t increase the volume in the jug past the 1500ml mark.

When you have finished:

Switch the appliance off (O) and unplug it.
Twist the jug in the opposite direction to Fig. B until the markings are aligned as Fig. A.

Blade Boost Function
The blade boost function helps you to free up ingredients that may have become stuck around the blade during blending.

With the motor running, place your hand on top of the jug lid and press the whole jug and blade assembly down (Fig. C).
Release the pressure and allow the jug to come back up again (Fig D).
Repeat this as required until the ingredients are processed to your satisfaction.

CARE AND MAINTENANCE

Switch the appliance off (O) and unplug it.
Wipe the outside of the motor unit with a clean damp cloth.
Wash the blade assembly as soon as possible, to prevent ingredients from drying and getting stuck.
To help clean the jug and blades add water and washing detergent to the jar, blend on high speed while pushing the jug up/down a few times.

You may wash these parts in the dishwasher.
If you use a dishwasher, the harsh environment inside the dishwasher will affect the surface finishes. The damage should be cosmetic only, and should not affect the operation of the appliance.

BLADE ASSEMBLY

The blade assembly can be removed for more thorough cleaning.

Remove the lid.
Turn the jug upside down.
Unscrew the blade assembly and lift it off the jug.
Handle only the plastic – don’t touch the metal parts.
Wash the blade assembly in warm soapy water, rinse, and air dry.
Replace the blade assembly and screw it firmly onto the bottom of the jug.

RECYCLING
To avoid environmental and health problems due to hazardous substances, appliances and rechargeable and non-rechargeable batteries marked with one of these symbols must not be disposed of with unsorted municipal waste. Always dispose of electrical and electronic products and, where applicable, rechargeable and non-rechargeable batteries, at an appropriate official recycling/collection point.

**26710-56 220-240V~50/60Hz 750 Watts![velleman DCM268 AC &amp DC CLAMP METER