inbertec CB110 Bluetooth Headset User Guide

inbertec CB110 Bluetooth Headset User Guide

Packing List

• Headset

• USB 2.0 (USB-A to USB-C)

• Bluetooth adaptor (Optional)

• Bag

• User Manual

USB Charging

Note: It is recommended to use 5V charger, and fully charge the headset for the first time, other specification charger may cause compatibility issues that prevent them from working properly

LED Indicator Status

On/Off/Battery/Connection Status

Pairing and Device Connection

Built-in Bluetooth
Step 1: Enter pairing mode

Step 2 : Select the headset from the Bluetooth device list

Note: If your PC doesn’t have built-in Bluetooth, you need to pair the headset with a Bluetooth dongle.

Pairing and Connecting Device
No Built-in Bluetooth Device

• Power On State

• Already pre-paired when leaving the factory,automatically connected

Note: To pair a second device, disconnect (unplug) the USB Bluetooth adaptor first. Then follow the instruction to pair the second device. After the second device is paired, reconnect the USB Bluetooth adaptor to enjoy 2 connections together.

Call Control and LED Indicator

Music Control

Wear the Headset

Notes

1. To give you a more efficient charging experience, please use the provided cable.
2. The red light is flashing on during charging, and bluelight will be on when the battery is fully charged.
3. When the battery level is low the headset will have a voice prompt “recharge headset”.
4. During use, click the “Multi function key” three times to check the current battery level and connection status.
   • battery high : 60%-100%
   • battery medium: 20%-60%
   • battery low : ＜20%
5. Follow below operations to check battery level and connection status.
   Operations| Connection Status| LED Indicator| Voice Prompt
   ---|---|---|---
   Three click multi function key| Connected(Standby or Music on)| Blue light on for 2s| “Battery high /medium/ low” “Connected”
   Three click multi function key| Disconnected| Red light on for 2s| “Battery high /medium/ low” “Disconnected”
6. Bluetooth: 2402-2480 MHz
   Bluetooth Headset: 7.11 dB m Dongle: 4 dBm
   Bluetooth : GFSK, π/4-DQPSK, 8D PS K

Safety Instructions

1. Do not disassemble this product or put it into fire or water to avoid short circuit, electric leakage, or damage to the product.
2. Don’t use this product in high temperature, humid, or corrosive environments to avoid failures.
3. Don’t contact this product with corrosive liquids, as it may cause serious damage.
4. Don’t disassemble or modify this product for any reason to avoid secondary failures and burns.
5. Don’t place the product at temperatures below – 10°C or above 55°C.
6. Don’t place the product at temperatures below 0°C or above 45°C while charging.
7. Don’t strike, throw, or strongly shock this product, as rough methods can damage the internal circuit board structure.

FCC Caution

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure requirement set forth for an uncontrolled environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>