PANADERO FENIX Wood Burning Stove Instruction Manual
- June 8, 2024
- PANADERO
Table of Contents
FENIX Wood Burning Stove
Instruction Manual
WOOD BURNING STOVE
- Nutrients.
- Ashes .
Wood: an ecological fuel
Wood is a renewable source of energy which answers the energy and
environmental demands of the 21st century. Throughout its long life, a tree
grows from sunlight, water,
mineral salts and CO2. Following the general pattern of nature, it soaks up
energy from the sun and supplies us with the oxygen essential for animal life.
The quantity of CO2 given off during the combustion of wood is no greater than
that given off by its natural decomposition. This means we have a source of
energy that respects the natural cycle of millions of years. Burning wood does
not increase the CO2 in the atmosphere, making it an ecological source of
energy which plays no part in the greenhouse effect.
In our wood-burning stoves logs are burnt cleanly without leaving any residue.
Wood ash is a high quality fertilizer, rich in mineral salts.
In buying a wood-burning stove, you will help the environment, your heating
will be very economical and you will be able to enjoy watching the flames,
something no other form of heating can offer.
USAGE AND MAINTENANCE INSTRUCTIONS
You have purchased a PANADERO product. Apart from correct maintenance, our
woodstoves require installation strictly in accordance with legislation. Our
products conform to the EN 13240:2001 and A2:2004 European norm, however it is
very important for you the consumer to know how to correctly use your
woodstove following the recommendations we set out. For this reason, before
installing our product you must read this manual carefully and follow the
usage and maintenance instructions.
POSITION OF THE SMOKE PIPE
- Place the first tube in the smoke outlet circle at the top of the stove, and attach the “other“ tube onto the end.
- Join it to the rest of the chimney.
- If the tubing reaches the exterior of your home, place the “hat” onto the end.
INSTALLATION
You have purchased a wood burning stove with a vermiculite insulated
combustion chamber.
Do not remove the vermiculite boards!!!!!
– All local regulations, including those referring to National and European
standards need to be complied with when installing the appliance.
– The installation of the smoke outlet must be as vertical as possible,
avoiding the use of joints, angles and deviations. If the installation is
connected to a masonry chimney pipe we recommend the tubes reach the exterior
exit. If the smoke outlet is via tubing only, at least three meters of
vertical tubing are recommended.
– IMPORTANT: The installation and regular cleaning of this stove must be
carried out by a qualified professional. The ventilation opening must never be
obstructed.
– IMPORTANT: The woodstove must be installed in a well ventilated place. It is
advisable to have at least one window in the same room as the stove which can
be opened.
– The tube connections should be sealed with a refractory putty to prevent
soot from falling through the joints.
– Do not position the stove near combustible walls. The stove should be
installed on a non-combustible floor surface, if not a metal plate covering
the bottom surface area of the stove must be placed underneath it and extend
further than 15 cm at the sides and 30 cm at the front.
– Whilst the stove is in use remove any material nearby which could be damaged
by the heat: furniture, curtains, paper, clothes, etc. The minimum safety
distance from adjacent combustible materials is as shown on the last page of
this manual.
– The ease of access for the cleaning of the product, smoke outlet and chimney
must be considered. If you intend to install your stove near an inflammable
wall, we advise you to leave a minimum distance to facilitate cleaning.
– You have just purchased a product that has an outside air intake of 80 mm
diameter. For the correct operation of your wood stove, you must install an 80
mm diameter pipe
to allow air to enter from outside.
– The stove should be installed on flooring with adequate support. If your
current floor does not comply with this criterion, it should be adapted with
appropriate measures (for example, a weight distribution plate).
FUEL
– Use only dry wood with a maximum moisture content of 20%. Wood with a
moisture content higher than 50 or 60% does not heat and combusts very badly,
and creates a lot of tar, releases excessive amounts of vapour and deposits
excess sediments onto the stove, glass and smoke outlet.
– The fire should be lit using special fire lighters, or paper and small
pieces of wood. Never try to light the fire using alcohol or similar products.
– Do not burn domestic rubbish, plastic materials or greasy products that can
pollute the environment and lead to risks of fire due to obstruction of the
pipes.
FUNCTION
– It is normal for smoke to appear during the first few uses of the stove, as
certain components of the heat-resistant paint burn whilst the pigment of the
actual stove is
fixed. Therefore the room should be aired until the smoke disappears.
– The woodstove is not designed to function with the door open under any
circumstances.
– The stove is intended to function intermitently with intervals for
recharging the fuel.
– For the lighting process of the stove it is recommended you use paper, fire
lighters or small sticks of wood. Once the fire starts to burn, add to it two
logs of wood each weighing 1.5 to 2 kg as a first initial charge. In this
lighting process the air inlets of the stove must be kept completely open. If
necessary the drawer for removing ashes can also be opened to begin with. Once
the fire is more intense, close the drawer completely (if open) and regulate
the intensity of the fire by closing and opening the air inlets.
– In order to achieve the stated nominal heat output of this stove a total
quantity of 1,83 kg of wood must be placed inside at intervals of 45 min. The
logs should be separate from one another, to In any instance a charge of fuel
must not be added to the has been burnt, leaving only a basic fire bed which
is no stronger.
– To achieve a slow combustion you should regulate the fire with the air
draughts, which must be kept permanently unblocked to allow the combustion air
to be distributed.
assure a correct combustion. stove until the previous charge enough to light
the next charge but
– After the first initial lighting, the brass pieces of the stove may become a
coppery colour.
– It is normal for the seal of the glass door panel to melt with use. Even
though the stove can function without this seal, it is recommended that you
replace it seasonally.
– The lower drawer can be removed in order to clear out ash. Empty it
regularly without waiting for it to fill up too much, to avoid the grill
becoming damaged. Take care with
the ash which may still be hot up to 24 hours after the stove has been used.
– Do not open the door abruptly in order to avoid smoke being released, and
never open it without opening the air draught beforehand. Open the door only
in order to put in
the appropriate fuel.
– The glass, brass pieces and stove in general may reach very high
temperatures. Do not expose yourself to risks of burns. When handling metal
pieces, use the glove provided with the stove.
– Keep children away from the stove.
– If you have trouble lighting the stove (due to cold weather, etc.) it can be
lit with folded or scrunched up paper which is easier to light.
– In case of the stove becoming too hot, close the air draughts to reduce the
intensity of the fire.
– In case of malfunction, contact us the manufacturers.
– For optimum performance, on ignition open only the primary air and once the
fire gets going (1 or 2 minutes) close off most of the primary air leaving
only a very small opening to allow for slow combustion.
– When you place the logs in the oven’s firewood rack, ensure they are not in
contact with the top
MAINTENANCE
– It is advisable to clean the glass door panel periodically to avoid
blackening by soot deposits. Professional cleaning products are available for
this. Never use water. Never clean the stove while it is in use.
– It is also important to clean the smoke outlet tubing periodically and check
there are no blockages before relighting fuel after a long period of non-use.
At the start of each season a professional should carry out a revision of the
installation.
– In the event of a fire in the smoke outlet, close all air draughts if
possible and contact the authorities immediately.
– Any replacement part which you may need must be recommended by us.
– The fiberglass cord used for the joints may degrade over time. If this
happens, you will have to replace it with a new fiberglass tape.
GUARANTEE
This is a high quality stove, manufactured with great care. Even so, if any
defect is found please first contact your distributor. If they are unable to
solve the problem they will contact us and send us the stove if necessary.
Our company will replace any faulty parts free of charge up to five years from
the date of purchase. We will not charge for repair work, however any
transport costs must be paid by the client.
Since this apparatus has been tested by a homologated laboratory the following
parts are NOT covered by warranty:
-Glass
-Internal grate
-Vermiculite
-Door handle, air-inlet knobs, etc.
In the interior of the packaging, you will find a quality control slip. We
request that you send this to your distributor in case of any claim.
MEASUREMENTS AND CHARACTERISTICS
– Height……………………………………………….. 854 mm
– Width ………………………………………………. 796 mm
– Depth………………………………………………… 463 mm
– Weight……………………………………………….. 141 Kg
– Firewood entrance……… 620 x 286 mm
– Smoke outlet …………………………150-153 mm
– Iron sheet body of 5 mm.
– Cast iron grill
– Paint, resistant up to 800 °C
– Vitro-ceramic glass, 750 °C
– Firewood up to 60 cm long| Nominal heat output …………………. 7.2 kW
– Energy efficiency …………………………. 78,9 %
– CO emission …………………………… 0.10%
– Minimum flue draught fornominal heatoutput………… 12 Pa
– Flue gas mass flow ……………………. 7,6 g/s
– Flue gas temperature …………………… 246°C
– Distance to adjacent
combustible materials………………….100 cm
– Heating volume (aprox.) …………. 250 m3
---|---
P.I. CAMPOLLANO
AVENIDA 5ª, 13-15
02007 ALBACETE -SPAIN
“FENIX” WOODSTOVE ………………………. 19
FREESTANDING ROOMHEATER FIRED BY SOLID FUEL
CERTIFICATE Nº 30-12098/T3
DECLARATION OF PERFORMANCE………………..18415
NOTIFIED BODY…………………………….1015
Thermal output ……………………………….. 7.2 kW
Energy efficiency ……………………………… 78,9 %
Emission of CO in combustion products………. 0.10%
Flue gas temperature………………….. 246 °C
Distance to adjacent combustible
materials ………………………………100 cm
Dust concentration at 13% O2 …………..330 mg/Nm
Fuel types……………………………… Firewood
HOW TO OPERATE YOUR WOOD STOVE EFFICIENTLY
https://panadero.com/how-to-operate-your-wood-stove-efficiently/ P
..II.. C AAMMPPOOLLLLAANNO
A VVEN I D AA 5 ªª,, 13 – 15
02007ALBACETE -SPAIN
Telf.: (+34) 967 59 24 00
Fax: (+34) 967 59 24 10
panadero@panadero.com