SYMMONS DURO FSTF367220 Floor Standing Tub Filler Instruction Manual

FSTF367220
Floor Standing Tub Filler
Operation & Maintenance Manual

Model Numbers

• FSTF367220 ……… Floor standing tub filler

Options/Modifications

Compliance

– ASME A11.18.1
– CSA B125.1

Feature Highlights

• Ceramic cartridge
• Push button to divert from spout to hand shower
• 60″ flexible metal hose
• 1 mode hand shower
• 2.0 gpm (7.6 L/min) hand shower
• Floor Standing Tub Filler shall be metal construction plated in standard polished chrome finish
• 5.3 gpm (20.1 L/min) at 45 psi tub filler
• 6.5 gpm (24.6 L/min) at 60 psi tub filler

Warranty

Limited Lifetime – to the original end purchaser in consumer/residential installations.
10 Years – for commercial/industrial installations. Refer to www.symmons.com/warranty for complete warranty information.

https://qrstud.io/zglfixh

Dimensions

Note: Dimensions subject to change without notice.

Measurements

A| 7″, 178mm
B| 2X1/2-14NPSM
C| 32-5/16″, 821mm
D| 11-5/8″, 296mm
E| 8-7/8″, 225mm
F| 31-1/8″, 790mm

Installation A) Wooden subfloor with access underneath
Section A: (Steps 1-4)

1. Measure and mark centerlines for mounting bracket installation using dimensions in the subfloor(1 1/2″ thick) where you would like the faucet to be located.

2. Drill a hole 2″ and (4x) 1/4″ holes. Use the floor flange(1) as a template.

3. Align with the holes of the floor flange(1) and the holes in the floor and insert (4x) bolts(2).

4. From underneath, install the holding plate, washers, lock washers, and nuts(4). Tighten the nuts with a wrench.
   Section B: (Step 5)

5. Install flooring around the floor flange.
   Section C (Steps 6 & 7)

6. Slide the decorative flange onto the faucet body.

7. Attach the flange to the body, using the 4 screwsprovided.
   Section D (Step 8-10)
   Direct Faucet body Installation:

8. Connect the faucet body and the floor flange together using the screws provided.
   Note: do not tighten screws entirely.

9. Before tightening the screws, rotate the faucet body in order to obtain the desired positionfor the spout.

10. Slide the decorative flange towards the floor.
    Section E (Step 11)

11. Connect the cold and hot water inlets. Check for leaks.
    Section F (Step 12)

12. Connect the hose and handshower to the shower holder connector. Check for leaks.

Installation B) Subfloor without access underneath

Section A: (Steps 1-3)

1. Measure and mark centerlines for mounting bracket installation using dimensions in the subfloor(1 1/2″ thick) where you would like the faucet to be located.

2. Drill a hole 2″ and (4x) holes (diameter depends on screws that customer used). Use the floor flange(1) as a template.

3. Flexible hose 1/2-14 NPSM, aligned with the corner holes of the floor flange and use appropriate screws according to the surface you are fastening the floor flange to (screws not included).
   Note: The floor flange can be flipped and used as shown if necessary.
   Section B: (Step 4 & 5)

4. Slide the decorative flange onto the faucet body.

5. Attach the flange to the body, using the 4 screws provided.
   Section C (Steps 6)

6. Connect the cold and hot water inlets. Check for leaks.
   Section D (Step 7-9)

7. Push the connected flexible hoses under the subfloor, then connect the faucet body and the floor flange together using the screws provided.
   Note: do not tighten screws entirely.

8. Before tightening the screws, rotate the faucet body in order to obtain the desired position for the spout.

9. Slide the decorative flange towards the floor. ** Section E (Step 10)**

10. Connect the hose and handshower to the shower holder connector. Check for leaks.

Symmons Industries, Inc. ■ 31 Brooks Drive ■ Braintree, MA 02184
■ Phone: 800-796-6667 ■ Fax: 800-961-9621
Copyright © 2021 Symmons Industries, Inc. ■ symmons.com
■ gethelp@symmons.com ■ ZV-3516 REV 0 ■ 042222

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>