SERVER EZT 4-Pouch Twin Topping Warmer User Manual

June 9, 2024
SERVER

SERVER logo EZT 4-Pouch Twin Topping Warmer
User Manual

EZT 4-Pouch Twin Topping Warmer

EZ-Topper™

SERVER EZT 4-Pouch Twin Topping Warmer - fig 1 Tall, Twin
MODEL: EZT
HERSHEY’S HOT FUDGE & CARAMEL 84969 COMPLETESERVER EZT 4-Pouch Twin Topping
Warmer - fig 2 Tall, Single
MODEL: EZT-S
HERSHEY’S HOT FUDGE 84967 COMPLETE HERSHEY’S CARAMEL 84965 COMPLETE
Thank You for your purchase. This pouched topping warmer virtually eliminates product degradation and waste, so you can reduce food costs while delivering a superior product.
SIMPLIFY TOPPING MANAGEMENT—GO POUCHED
Used with 48 fl. oz pouches with 16mm center fitments.

PARTS

SERVER EZT 4-Pouch Twin Topping Warmer - fig 4

SAFETY

WARNING- ELECTRICAL SHOCK COULD OCCUR
This unit must be earthed or grounded.
This requires all three prongs (terminals) on cord  plug to be plugged into power source. According to food and safety regulations, most foods must be stored and/or served at certain temperatures or they could become hazardous. Check with local food and safety regulators for specific guidelines.
Be aware of the product you are serving and the temperature the product is required to maintain. Server Products, Inc. can not be responsible for the serving of potentially hazardous product.

PRE-HEATING PRODUCT POUCHES

  • Install pump with pouch. (See UNIT SETUP, pg. 4.)
  • Adjust thermostat to food manufacturer’s recommended serving temperature.

SERVER EZT 4-Pouch Twin Topping Warmer - fig 5 Cutaway views show:
Reserve Pouch in base bottom
Pouch Support in base bottom
Make change-outs a cinch.
Place a reserve pouch in the bottom of the base.
When the primary pouch is emptied, the reserve pouch is pre-heated and ready for use.

UNIT SETUP

SEE SEPARATE PUMP MANUAL FOR PUMP SETUP.
INSERT INTO BASE: POUCH SUPPORT RESERVE POUCH
IMPORTANT: A pouch support or reserve pouch gives the primary pouch the proper elevation to dispense all product and heat evenly.
SERVER EZT 4-Pouch Twin Topping Warmer - fig 6 ATTACH PUMP TO PRIMARY POUCH

  • Place pouch on countertop with pouch fitment circle facing upward.
  • Position pump connector directly over center of pouch fitment.
  • Press pump connector down to pierce through film in pouch fitment.

SERVER EZT 4-Pouch Twin Topping Warmer - fig 7Pump is fully engaged when top surface of pouch fitment touches pump connector rim. INSTALL PUMP WITH POUCH INTO BASESERVER EZT 4-Pouch Twin Topping Warmer -
fig 9 PLUG CORD into power source.
PRESS SWITCH to the “ON” position.
SET THERMOSTAT KNOB to food manufacturer’s recommended serving temperature.

SERVER EZT 4-Pouch Twin Topping Warmer - fig 10• Dial indicator uses increments of 5º F.
• Thermostat maximum is 210º F/99º C.

UNIT TAKE-DOWN

  1. PRESS SWITCH to the “OFF” position.

  2. UNPLUG CORD
    SERVER EZT 4-Pouch Twin Topping Warmer - fig 11 CAUTION- HOT
    Allow unit to cool before continuing or use proper care with hot surfaces.

  3. REMOVE PUMP WITH POUCH

  4. REMOVE POUCH SUPPORT OR RESERVE POUCH
    SERVER EZT 4-Pouch Twin Topping Warmer - fig 12

  5. DETACH POUCH from bottom of pump.

  6. FLUSH AND RINSE PUMP
    Thoroughly rinse all inside and outside surfaces of pump with hot water.

  7. DISASSEMBLE AND CLEAN PUMP.
    SEE SEPARATE PUMP MANUAL FOR PUMP CLEANING.

CLEANING

SEE SEPARATE PUMP MANUAL FOR PUMP INSTRUCTIONS.
WARNING- ELECTRICAL SHOCK COULD OCCUR

  • Electrical components of unit could be damaged from water exposure or any liquid.
  • Never immerse unit into water or any liquid.
  • Never use any water jet or pressure sprayer on unit.
  • Ensure unit is “OFF” and unplugged.

CAUTION- HOT
Allow unit to cool before cleaning.SERVER EZT 4-Pouch Twin Topping Warmer -
fig 14

CLEAN EXTERNAL SURFACES

  • Wipe daily with a clean damp cloth.
  • Dry with a clean soft cloth.
  • Glass and surface cleaners approved for use in food contact areas may be used.

CARE OF STAINLESS STEEL

This warmer and accessories are constructed of stainless steel— one of the best materials for food serving and storage.
If you notice corrosion beginning on any stainless steel surface, you may need to change the cleansing agent, sanitizing agent, or the cleaning procedures you are using.

  • A mildly abrasive nylon or brass brush may be used to remove any stubborn food or mineral deposits on interior surfaces of unit.
  • Fully rinsing and drying all parts can help prevent corrosion. Elements and minerals in tap water can accumulate on stainless steel parts and create corrosion.
  • Do not use abrasive, caustic or ammonia based cleansers.
  • Do not use products containing acids, alkalines, chlorine, or salt. These agents can corrode stainless steel.
  • Do not use metal scrapers or cleaning pads that could scratch surfaces.

WIRING 120V | USA

SERVER EZT 4-Pouch Twin Topping Warmer - fig 15

  1. Cord Assembly
  2. Bushing/Strain Relief
  3. Snap-In Rocker Switch
  4. 6″ Wire Assembly, Black
  5. Thermostat
  6. Heating Element
  7. 15″ Wire Assembly, Green

SERVER EZT 4-Pouch Twin Topping Warmer - fig 16

  1. Cord Assembly
  2. Bushing/Strain Relief
  3. Snap-In Rocker Switch
  4. 6″ Wire Assembly, Black
  5. Thermostat
  6. Heating Element
  7. 6″ Wire Assembly, Green
  8. 18″ Wire Assembly, Green

TROUBLESHOOTING

UNIT DOES NOT HEAT?

  • Ensure cord is securely plugged in.
  • Ensure unit is on.
  • Ensure thermostat knob is set correctly.
  • Ensure power is available from source.
  • Do not allow any of the electrical components to get wet. Moisture may cause the unit to trip breaker or GCFI. If moisture is suspected, discontinue use. Allow unit to fully air dry.

POUCH DOES NOT EVACUATE ALL PRODUCT?

  • Ensure that the pouch is properly connected with pump.
  • Ensure that the pouch being dispensed is raised to proper height. Always use either a pouch support or a reserve pouch beneath  primary pouch.

SERVER PRODUCTS LIMITED WARRANTY

**2 YEAR WARRNTY**
This Server product is backed by a two-year limited warranty against defects in materials and workmanship. See Server-Products.com for details..

GENERAL SERVICE, REPAIR OR RETURNS

Before sending any item to Server Products for service, repair, or return, contact Server Products customer service to request a Return Authorization Number. Merchandise must be sent to Server Products with this number. Service is extremely prompt. Typically, units are repaired and ship out within 48 hours of receipt. Merchandise being returned for credit must be in new and unused condition and not more than 90 days old and will be subject to a 20% restocking charge. Electrical parts (thermostats, heating elements, etc.) are not returnable.
Servicing Cord: Specific tools are required for safe and proper power supply cord removal and installation. If cord must be replaced, only a representative of the OEM (original equipment manufacturer) or a qualified technician may replace cord. Cord must meet code designation H05 RN-F requirements.

NEED HELP?
Server Products Inc.
3601 Pleasant Hill Road
Richfield, WI 53076 USA
Chat with us!
spsales@server-products.com
262.628.5600 | 800.558.8722
Please be prepared with your Model
P/N and Series located on the lid or base of the unit.
Example:

Documents / Resources

| SERVER EZT 4-Pouch Twin Topping Warmer [pdf] User Manual
EZT, EZT-S, 4-Pouch Twin Topping Warmer, Twin Topping Warmer, 4-Pouch Topping Warmer, Topping Warmer, Warmer
---|---

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals