JBC SMR Multiplexer for Robot Instruction Manual
- June 9, 2024
- JBC
Table of Contents
www.jbctools.com
SMR Multiplexer for Robot
Instruction Manual
SMR
Multiplexer for Robot
SMR Multiplexer for Robot
This manual corresponds to the following references:
SMR-A
Packing List
The following items are included: Multiplexer for Robot ……………………….. 1 unit
Cabel M8F-M8M 5V (3m) ………………….. 2 unit
Ref. 0021333 Manual ………………………………………………….. 1 unit
Ref. 0023789 Cable DB9M-DB9F (2m) ……………………. 1 unit
Ref. 0028514 AC Adapter ………………………………………… 1 unit
Ref. 0028084
Features
SMR simplifies the connection between the PC or PLC and the JBC stations by
multiplexing one serial communication port towards two JBC Devices.
– UCR – Control Unit for Automation (serial communication RS-232)
– SFR – Solder Feeder for Robot (serial communication RS-232)
*See corresponding “Communication Protocol” at www.jbctools.com/jbcsoftware.html.
Connection
Connection module for automation process
Ref. SMR-A
Installation
Connect the SMR with the supplied AC adapter (1). The DC IN indicator must
become lighted
Connect the PC/PLC serial port DB9 male connector to the SMR by using the DB9
cable (2).
Connect two JBC Devices to the SMR by using the M8F-M8M 5V 3M cables (3).
Typical devices are the
UCR Control Unit (4) and de SFR Solder Feeder for Robot (5).
Ensure that both device protocol settings are configured as “WITH ADDRESS” and
the address of each devices is different. Default address values is 01 for the
UCR and 10 for the SFR.
LED Indicators
The indicator lights STATION 1, STATION 2, and PC are very useful for
debugging communications:
PC Indicator Light
PC indicator (6) blinks every time the PC sends bytes to the stations. If
this led doesn’t blink, the port number assigned to the communication software
is incorrect.
Station Indicator Light
STATION1 and STATION2 lights (7) blink when the JBC devices answers a frame to
the PC. If these lights don’t blink, check if the address settings are
properly defined.
If the device adress is unknown, JBC recommends to download the Robot Control
Software* and use the “Discovery Connected Devise” funktion.
Maintenance
– Before carrying out maintenance, always allow the equipment to cool down.
– Periodically check all cables and connections.
– Replace any defective or damaged part. Use original JBC spare parts only.
– Repairs should only be performed by JBC and authorized technical service.
Safety
**** It is imperative to follow safety guidelines to prevent electric shock,
injury, fire or explosion.
– Do not use the device for other purpose.
– The AC Adapter must be plugged into approved bases. When unplugging it, hold
the plug, not the wire.
– Be sure that the power supply is disconnected before changing any spare
part.
– Keep your workplace clean and tidy. Wear appropriate protection glasses and
gloves when working to avoid personal injury.
Specifications
SMR
Multiplexer for Robot
Ref. SMR-A
– Total Net Weight: 505 g / 1.11 lb
– Package Dimensions/Weight: 246 x 184 x 42 mm / 567 g
(L x W x H) ……….. 9.69 x 7.24 x 1.65 in / 1.25 lb
Complies with CE standards.
Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects,
including the replacement of defective parts and labour.
Warranty does not cover product wear or misuse.
In order for the warranty to be valid, equipment must be returned, postage
paid, to the dealer where it was purchased.
This product should not be thrown in the garbage.
In accordance with the European directive 2012/19/EU, electronic equipment at
the end of its life must be collected and returned to an authorized recycling
facility. a manuales – color gris.
www.jbctools.com
*Download the Robot Control Software, available at
www.jbctools.com/jbcsoftware.html
0023789-090922
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>