COMPASS HEALTH PB6034 Reduced Gap Full-Length Bed Rail Instruction Manual
- June 4, 2024
- COMPASS HEALTH
Table of Contents
COMPASS HEALTH PB6034 Reduced Gap Full-Length Bed Rail Instruction Manual
SAVE THESE INSTRUCTIONS
NOTE: Check all parts for shipping damage before using. In case of damage, DO
NOT use the equipment. Contact the dealer/carrier for further instructions.
To ensure the safe use of the reduced gap full-length bed rail, these
instructions MUST be followed:
WARNINGS
DO NOT install or use this equipment without first reading and understanding these instructions. If you are unable to understand the Warnings, Cautions or Instructions, contact a healthcare professional, dealer or technical personnel before attempting to install this equipment – otherwise, death, injury or property damage may occur.
These bed rails are intended to prevent an individual from inadvertently rolling out of bed. DO NOT use for restraint purposes.
ENTRAPMENT MAY OCCUR. Proper patient assessment and monitoring, and proper maintenance and use of equipment is required to reduce the risk of entrapment. Variations in bed rail dimensions, and mattress thickness, size or density could increase the risk of entrapment. Visit the FDA website at http://www.fda.gov to learn about the risks of entrapment.
Compass products are specifically designed and manufactured for use in conjunction with Compass accessories. Accessories designed by other manufacturers have not been tested by Compass and are not recommended for use with Compass products.
Although bed rails are not rated to any specific weight limitation,the bed rails may become deformed or broken if excessive side pressure is exerted on the bed rails.
This bed rail is not an assist rail for getting into or out of bed. DO NOT use the bed rails as push handles when moving the bed.
After any adjustments, repair or service and before use, make sure all attaching hardware is tightened securely. Bed rails with dimensions differentfrom the original equipment supplied or specified by the bed manufacturer may not be interchangeable and may result in entrapment or other injury.
One crossbrace MUST be positioned between the sixth and seventh springs at the head end of the bed. The remaining crossbrace MUST be positioned between the second and third springs at the foot end of the bed. Otherwise, either the bed rail or the bed may be damaged when the head end and/or foot end are raised.
WARNING
To ensure proper bed rail installation, arrows on crossbrace decal MUST point to center of bed.
The outer telescoping tube of the bed rail MUST be positioned at the head end of the bed to prevent a pinch point when raising/lowering bed.
To reduce the risk of entrapment make certain that the crossbraces DO NOT exceed the width of the mattress. Mattress MUST fit bed frame and side bed rails snugly to reduce the risk of entrapment.
Unless the bed rail is in the lowest position, ensure that the spring loaded knobs fully protrude through the same respective adjustment hole of each bed rail tube. This ensures that the bed rail is securely locked in position and an even height adjustment is achieved (The lowest position for the bed rail occurs when the bed rail rests against the bed rail stop. Spring loaded pins DO NOT engage into an adjustment hole when the bed rail in the lowest position.)
Install bed rails fully extended on bed. DO NOT use full length bed rails as half rails.
Installing the Crossbraces
NOTE: READ AND UNDERSTAND WARNINGS before proceeding with Installing the Crossbraces on page 2.
NOTE: For this procedure, refer to FIGURE 1 on page 3.
-
Remove the mattress from the bed.
-
Place the bed in the flat position and position one crossbrace between the sixth and seventh springs at the head end of the bed frame (Detail “A”).
NOTE: If the bed frame contains BLACK springs at the sixth and seventh spring locations at the head end of the bed, position the crossbrace between these springs. -
When holding either end of the crossbrace assembly, turn the barrels so plunger knobs are on top (Detail “A”).
NOTE: Ensure the long end of the barrel faces the center of the bed with the decal to the center of bed as shown in FIGURE 1. If long end faces the opposite way, rotate crossbrace 180°. -
Position the bed hooks so they are on the bottom side of the crossbrace (Detail “B”).
-
Perform one of the following:
-
Standard Hardware Installation – Attach one bed hook onto the bed spring angle iron and push in on the spring loaded bed rail until you are able to attach the opposite end to the bed spring angle iron (Detail “B”).
NOTE: Ensure plunger pins are facing the center of the bed. -
Optional Hardware Installation – Perform the following steps:
- Attach wingnuts to bed hooks.
- Tighten until the wingnut reaches the bed spring angle iron.
-
-
Rotate the barrels of the crossbrace until the barrels are vertical and the long ends of the barrels are facing DOWN.
-
Position the remaining crossbrace between the second and third springs at the foot end of the bed.
NOTE: If the bed frame contains BLACK springs at the second and third spring locations at the foot end of the bed, position the crossbrace between these springs. -
Repeat STEPS 3-7 for the foot end crossbrace.
-
Place mattress on bed frame.
-
Install the bed rails. Refer to Installing the Bed Rails on page 3
Installing the Bed Rails
WARNING
The outer telescoping tube of the bed rail MUST be positioned at the head end of the bed to prevent a pinch point when raising/lowering bed.
NOTE: READ AND UNDERSTAND WARNINGS before proceeding with Installing the Bed Rails.
NOTE: For this procedure, refer to FIGURE 2 on page 4.
- Extend one bed rail to reach the head end and foot end crossbraces.
- Insert the outer telescoping tube of the bed rail into the barrel of the head end crossbrace.
- Pull and hold the plunger knob on the barrel while lowering the bed rail.
- Release the plunger knob on the barrel.
- Raise or lower the bed rail until the plunger pin clicks securely into the adjustment hole or until the bed rail stop rests against the barrel.
- Insert the inner telescoping tube of the bed rail into the barrel of the foot end crossbrace.
- Repeat STEPS 3-5 for the inner telescoping tube of the bed rail, adjusting the bed rail to the position reached in STEP 5.
- Repeat STEPS 1-7 to install the other bed rail onto the opposite side of the bed.
Operating Instructions
NOTE: READ AND UNDERSTAND WARNINGS before proceeding with Operating Instructions.
Lowering/Raising the Bed Rails
-
Hold bed rail while pulling the plunger knob.
-
Lower/raise bed rail.
-
Release plunger knob and lower/raise the bed rail until the plunger pin clicks into position unless the bed rail is at the lowest position.
NOTE: The lowest position for the bed rail is when the bed rail rests against the bed rail stop.
Spring loaded pins DO NOT have an adjustment hole to engage into when the bed rail is in the lowest position. -
Repeat STEPS 1-3 for opposite end of bed rail.
NOTE: Ensure head end and foot end of bed rails are adjusted to the same height.
LIMITED WARRANTY
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser who purchases this product when new and unused from Compass or a dealer. This warranty is not extended to any other person or entity and is not transferable or assign able to any subsequent purchaser or owner. Coverage under this warranty will end upon any such subsequent sale or other transfer of title to any other person.
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.
Compass warrants its product to be free from defects in materials and work man ship for one year for the original purchaser. If with in such warranty period any such product shall be proven to be defective, such product shall be repaired or replaced, at Compass’ option. This warranty does not include any labor or shipping charges incurred in replacement part installation or repair of any such product. Compass’ sole obligation and your exclusive remedy under this warranty shall be limited to such repair and/or replacement.
For warranty service, please contact the dealer from whom you purchased your Compass product. In the event you do not receive satisfactory warranty service, please write directly to Compass at the address on the back cover, provide dealer’s name, address, and the date of purchase, indicate nature of the defect and, if the product is serialized, indicate the serial number. Do not return products to our factory without our prior consent.
LIMITATIONSAND EXCLUSIONS: THE FOREGOINGWARRANTY SHALLNOTAPPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL NUMBER HAS BEEN REMOVED ORDEFACED, PRODUCTS SUBJECTED TO NEGLIGENCE,ACCIDENT,IMPROPER OPERATION, MAINTENANCE OR STORAGE, PRODUCTS MODIFIED WITHOUT COMPASS’EXPRESS WRITTEN CONSENT(INCLUDING,BUT NOTLIMITED TO, MODIFICATION THROUGH THE USE OF UNAUTHORIZED PARTS OR ATTACHMENTS; PRODUCTSDAMAGED BY REASON OFREPAIRS MADE TO ANYCOMPONENT WITHOUT THE SPECIFIC CONSENT OF COMPASS, ORTO A PRODUCT DAMAGED BY CIRCUMSTANCES BEYOND COMPASS’ CONTROL, AND SUCH EVALUATION WILL BE SOLELY DETERMINED BY COM[ASS. THE WARRANTY SHALLNOTAPPLY TO NORMAL WEAR AND TEARORFAILURE TO ADHERE TO THE PRODUCT INSTRUCTIONS.
THE FOREGOING EXPRESS WARRANTY ISEXCLUSIVEAND INLIEU OFANYOTHER WARRANTIES WHAT SO EVER,WHETHER EXPRESS ORIMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,AND THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY WHATSOEVER,SHALLBE LIMITED TO REPAIR OR REPLACEMENTOFTHE DEFECTIVE PRODUCT PURSUANTTO THE TERMSCONTAINED HEREIN. THEAPPLICATIONOFANY IMPLIEDWARRANTY WHATSOEVER SHALLNOTEXTEND BEYOND THE DURATION OFTHE EXPRESS WARRANTY PROVIDED HEREIN. COMPASS SHALLNOTBE LIABLE FOR ANY CONSEQUENTIAL ORINCIDENTAL DAMAGES WHATSOEVER.
SOME STATES DO NOTALLOWTHE EXCLUSION ORLIMITATION OFINCIDENTAL OR CONSEQUENTIAL DAMAGE,ORLIMITATION OFHOW LONGANIMPLIEDWARRANTY LASTS,SO THEABOVE EXCLUSION AND LIMITATION MAY NOTBE APPLICABLE.
THISWARRANTY SHALLBE EXTENDED TO COMPLYWITHSTATE/PROVINCIAL LAWS AND REQUIREMENTS.
Manufactured for:
Compass Health Brands
6753 Engle Road
Middleburg, OH, 44130
www.compasshealthbrands.com
Documents / Resources
|
COMPASS HEALTH PB6034 Reduced Gap Full-Length Bed
Rail
[pdf] Instruction Manual
PB6034, Reduced Gap Full-Length Bed Rail, Gap Full-Length Bed Rail, Full-
Length Bed Rail, PB6034, Bed Rail
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>