JBC CLMRP Tip Cleaner for Robot Instruction Manual

: June 9, 2024
: JBC

Table of Contents

Packing List
Features
Connection
Work Position Adjustment
Accessories: Brush Ranges
Changing Brushes
Dimensions
Work Place Examples
Maintenance
Safety
Specifications
Read User Manual Online (PDF format)
Download This Manual (PDF format)

JBC CLMRP Tip Cleaner for Robot Instruction Manual

This manual corresponds to the following references:

CLMR-PA with Fiber Brushes

Packing List

According purchased reference either one or the other cleaner is included:

Tip Cleaner for Robot with Fiber Brushes.. 1 unit
CL2008 Fiber Brushes (black core) …… 1 pair Ref. CL2008 (includes 2 brushes
Connector Cable (3m) ……………………. 1 unit Ref. 0024563
Manual …….. 1 unit Ref. 0029764

Features

CLMRP and CLMR are automatic tip cleaners with two motorized brushes. They feature a large capacity collecting container with easy extraction and a wide opening for easy access to the soldering tip.

Features

Connection

CLMRP/CLMR can be connected to a PLC by a five-pin connector cable.

Connection

The connector provides “switch” input and power supply.

The input switch manages the cleaner’s activity. It can be connected to a PLC’s digital output and accepts PNP, NPN or relay contacts.

For detailed information about pin distribution see following table:

Front view CLMR Power Connector

Connection

Power Connector

Work Position Adjustment

CLMRP/CLMR can be turned up to 35º in both directions to facilitate the cartridge tip’s insertion.
Work Position Adjustment

To pivot the CLMRP/CLMR, loosen and tighten the handle to turning it. The Handle can be aligned vertically again by pressing the Push Button.
Work Position Adjustment

Accessories: Brush Ranges

All brushes are offered with black and blue core, to distingish them when working with lead-free and leaded solder.

Note: As a refereance, the cleaning process should last around 1 second.

| C L1008| CL1007| CL2008|

CL20 07

---|---|---|---|---
| | | |

Brush Material

|

Metal

|

Metal

|

Fiber

|

Fiber

Changing Brushes

Easily replace brushes and clean the solder collector tray as follows:

Unplug CLRMP from the mains and open the side closures.
Remove the Splashguard and press the brush‘s buttons (1) to remove them (2).
Align the brush axis with the motor axis and insert the brushes. Push them in until a click is heard. Check if the brushes are properly affixed.
The Splashguard also works as a tin collector Clean it and place it back in its position.

Dimensions

Work Place Examples

HA Automatic Soldering Set for Robot

Place Examples

HM Soldering Set for Robot
Place Examples

Maintenance

Before carrying out maintenance or storage, unplug the equipment from the mains supply.
Use a damp cloth to clean the splashguard outside and inside.
Keep the brushes clean and replace them when necessary.
Periodically check all cables and tube connections.
Replace any defective or damaged parts. Use original JBC spare parts only.
Repairs should be performed only by a JBC authorized technical service.

Safety

It is imperative to follow safety guidelines to prevent electric shock, injury, fire or explosion.

Do not use the equipment for any purpose other than tip cleaning. It is not a tool stand.
Do not leave the equipment unattended when it is on.
You must turn the device off before changing the brushes.
The temperature of accessible surfaces may remain high after the equipment is turned off. Handle with care.
Heat can cause inflamable products to ignite even when not visible.
Avoid contact when brushes are rotating.
Be carefull with the fumes produced when soldering.
Keep your workplace clean and tidy. Wear appropriate protection glasses and gloves when working to avoid personal injury.
Utmost care must be taken with liquid tin waste which can cause burns.

Specifications

CLMRP
Tip Cleaner for Robot with Fiber Brushes
Ref.: CLMR-PA
CLMR
Tip Cleaner for Robot with Metal Brushes
Ref.: CLMR-A
Brush diameter: 50 mm / 2.0 in
Net Weight: 2737 g / 6.03 lb
Package Dimensions/Weight: 221 x 136 x 126 mm / 3060 g
(L x W x H) 8.70 x 5.35 x 4.96 in / 6.75 lb
Complies with CE standards.
ESD safe

Warranty
JBC’s 2 year warranty covers this equipment against all manufacturing defects, including the replacement of defective parts and labour. Warranty does not cover product wear or misuse. In order for the warranty to be valid, equipment must be returned, postage paid, to the dealer where it was purchased.

This product should not be thrown in the garbage. In accordance with the European directive 2012/19/EU, electronic equipment at the end of its life must be collected and returned to an authorized recycling facility

CE icon EAC Icon