Eufycam 2C Pro Wire-free 2K Security Camera Set User Manual

: June 11, 2024
: Eufy

Eufycam 2C Pro Wire-free 2K Security Camera Set

QUICK START GUIDE

1. GETTING STARTED

For HomeBase 2 installation

For eufyCam 2C Pro installation

1. Camera quantity and accessories vary by bundle package.

2. HomeBase 2 power adapter varies by region.

2. PRODUCT OVERVIEW

HomeBase 2

1. Status LED
2. Speaker
3. Power port
4. USB port
5. Ethernet port
6. SYNC/ALARM OFF button
7. Reset button

eufyCam 2C Pro

OVERVIEW

1. Lens
2. Light sensor
3. Microphone
4. Motion sensor
5. Spotlight
6. Status LED
7. SYNC button
8. Mounting hole
9. Charging port
10. Speaker

3. CONNECTING THE HOMEBASE 2

Connect the HomeBase 2 to the Internet

1 . Power on the HomeBase 2, then use the ethernet cable provided to connect the HomeBase 2 to your home router.

2. The LED indicator turns blue (this may take up to I min) when HomeBase 2 is ready for setup.

4. SETTING UP THE SYSTEM

Download the App and Set up the System

Download the eufy Security app from the App Store (iOS devices) or Google Play (Android devices).

Sign up for a eufy Security account, then follow the onscreen instructions to complete the setup.

5. MOUNTING THE CAMERA

Find a Good Mounting Spot

To find a spot to mount eufyCam 2C Pro, you need to test wireless signal strength.
CD Open the eufy Security app, go to Camera Settings > Mounting Guide.
@ To test the wireless signal strength, take your camera and phone to the location where you want to mount the camera.
® Move the camera as close to the HomeBase 2 as possible if the wireless signal strength is poor.

Select Height and Location

Hang eufyCam 2C Pro 7-10 ft (2-3 m) above the ground.T his height maximizes the detection range of the motion sensor of eufyCam 2C Pro. Avoid placing eufyCam 2C Pro under direct sunlight.

Select Height and Location

Mount the camera

The camera can be mounted both indoors and outdoors.

1 .Tum the knob of the mounting bracket clockwise to loosen and disassemble it.

2. Drill holes with a I 5/64 inch (5.95mm) drill bit, then insert the anchors into the holes; anchors are necessary for walls that are made out of hard materials such as concrete, brick, or stucco.

3. Firmly screw the base of the mounting bracket onto the wall. Fasten the ball knob of the bracket to the base of the bracket.

4.Tighten eufyCam 2C Pro to the mounting bracket and adjust the viewing angle by checking the live stream feed in the eufy Security app.

Tips:
1 .The Homebase 2 pairs up to 16 cameras, you can repeat the steps mentioned above to add more eufyCam 2C Pro cameras to meet different needs of use.
2. For troubleshooting, check Help on the eufy Security App.

6. CHARGING EUFYCAM 2C PRO

Charge eufyCam 2C Pro

7. NOTICE

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (I ) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comp with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However; there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna
Increase the separation between the equipment and receivec
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radiofTV technician for help.

FCC Radio Frequency Exposure

Statement: The device has been evaluated to meet general RF exposure requirements.The device can be used in fixed/mobile exposure condition.The min separation distance is 20cm.

Notice : Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.

The following importer is the responsible party Company Name: POWER MOBILE LIFE, LLC Address: 400 I 08th Ave NE Ste 400, Bellevue, WA 98004-5541
Telephone: 1-800-988-7973

CE This product complies with the radio interference requirements of the European Community

Declaratlon of Conformity

Hereby. Anker Innovations Limited declares that this device is in compliance wrth the essential requirements and other relevant provisions of Directive 2014/53/EU. For the declaration of conformity, visit the Website www.eufylife.com Due to the used enclosure material, the product shall only be connected to a USB Interface of version 2.0 or highec
The adapter shall be installed near the equipment and shall be easily accessible.
Do not use the Device in the environment at too high or too low temperature, never expose the Device under strong sunshine or too wet environment.
The suitable temperature for HomeBase 2 and accessories is -I 0°C-45°C.
The suitable temperature for eufyCam 2C Pro and accessories is -20°C-S0°C.
When charging, please place the device in an environment that has a normal room temperature and good ventilation.

It is recommended to charge the device in an environment wrth a temperature that ranges from S°C~25°C.
Please ensure to use only the charger offered by the manufacturer Using unauthorized charger may cause danger and violate the authorization of the device and the guarantee article.

This charger is for indoor use only
The charger type is ASSA67W- I 20200, output voltage/current is I 2Vdd2A.The plug considered as disconnect device of adapter RF exposure information:The Maximum Penmissible Exposure (MPE) level has been calculated based on a distance of d=20 cm between the device and the human body. To maintain compliance with RF exposure requirement, use product that maintain a 20cm distance between the device and human body.

CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

Wi-Fi Operating Frequency Range: 2412~ 2472MHz : Wi-Fi Max OutputPower: 17.13 dBm (ERIP for T80I0), 17.9 dBm (ERIPforT8I42)

SUB-I G Frequency range: 866~866.SMHz: SUB- I G Output Power: 5.492 dBm (ERi P for T8 I 4 2)
The following importer is the responsible party (contact for EU matters only)

Importer : Anker Technology (UK) Ltd Importer Address: Suite B, Fairgate House, 205 Kings Road,Tysele Binmingham, BI I 2AA, United Kingdom

@ This product is designed and manufactured with high quality materials and components, which can be recycled and reused.

This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resounces, human heatth and the environment. For more information on disposal and recycling of this product, contact your local municipalify, disposal service, or the shop where you bought this pnoduct.

IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is sub1ect to the following two conditions:

1. this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.”

IC RF Statement:
When using the product, maintain a distance of 20cm fnom the body to ensure compliance with RF exposure requirements.

8. LEGAL NOTICE

Use of the Works with Apple HomeKit badge means that an electronic accessory has been designed to connect specifically to iPod touch, iPhone, or iPad, respectively, and has been certified by the developer to meetApple performance standards.Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Customer Service

Warranty
I2-month limited warranty

Call Us
United States: + 1 (800) 988 7973 Mon-Fri 9AM-SPM (PT)
United Kingdom: +44 (0) 1604 936 200 Mon-Fri 6AM- I I AM (GMT)
Genmany: +49 (0) 69 9579 7960 Mon-Fri 6:00-1 I :00

Email Us
Customer Support: [email protected]
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong