Harley Benton Spaceship Power 50C User Guide

: June 9, 2024
: Harley Benton

Table of Contents

Harley Benton Spaceship Power 50C
Safety instructions
Features
Scope of delivery
Operating elements
Using the product
Technical specifications
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Harley Benton Spaceship Power 50C

Safety instructions

Intended use
This product is meant to be used as a multiple power supply for effect pedals. Any other use or use under other operating conditions is considered to be improper and may result in personal injury or property damage. No liability will be assumed for damages resulting from improper use.
Danger for children

Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking hazard! Ensure that children do not detach any small parts from the product. They could swallow the pieces and choke! Never let children unattended use electri-cal devices.

Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present. Never remove any covers. There are no user-serviceable parts inside. Do not use the device if covers, protectors or optical components are miss-ing or damaged.

Electric shock caused by short-circuit
Do not modify the mains cable or the plug. Failure to do so could result in electric shock/death or fire. If in doubt, seek advice from a registered electrician.

Possible staining
The plasticiser contained in the rubber feet of this product may possibly react with the coating of your surface and after some time cause perma-nent dark stains. In case of doubt, do not put the rubber feet directly on the surface and use a suitable underlay if necessary, i.e. felt-pad floor pro- tectors or similar.

Where to use the product Never use the product

in conditions of extreme temperature or humidity
in extremely dusty or dirty areas
at locations where the unit can become wet

General handling

To prevent damage, never use force when handling the product.
Never immerse the product in water. Just wipe it with a clean dry cloth. Do not use liquid cleaners such as benzene, thinners or flammable cleaning agents.

Features

Lightweight, compact pedalboard with integrated power adapter
Powder-coated aluminium frame
Universal input voltage operation 100 – 240 V
7 insulated, filtered and short-circuit proof outputs eliminate noise and hum

Scope of delivery

3 × DC cable with a length of 30 cm
3 × DC cable with a length of 60 cm
3 × DC cable with a length of 90 cm
1 × reverse polarity cable with red plug
1 × battery clip
1 × connector cable with a length of 45 cm with 5.5 × 2.5 mm green coaxial plug to 5.5 × 2.1 mm coaxial plug
1 × connector cable with a length of 45 cm with 3.5 mm jack plug to 5.5 × 2.1 mm coaxial plug
1 × voltage boost cable, 20 cm
1 × current boost cable, 60 cm
1 × EIAJ-05 cable
1 × power cord with EU plug, 120 cm
1 × cable fastening set
1 × velcro tape, self-adhesive, 200 mm × 45 mm
1 × Allen key
1 × transport bag with storage pocket and shoulder strap

Operating elements

Harley-Benton-Spaceship-Power-50C-FIG-1

USB-A output, uninsulated
USB-C output, uninsulated
IEC chassis connector C14 for connecting the supplied power cord 4 Output 1 with 24 V @ 2000 mA, uninsulated
Output 2 with 9 V @ 3000 mA, uninsulated
Outputs 3 – 4 with each 9 V @ 250 mA, insulated
Outputs 5 – 7 with each 9 V @ 500 mA, insulated
Outputs 8 – 9 with voltage switches, insulated, switchable between
- 9 V @ 500 mA /
- 12 V @ 375 mA /
- 18 V @ 250 mA
Control LED for outputs 1 – 9, lights up green when voltage is present, turns off when output is deactivated due to overload

Using the product

Connect the device to the mains using the supplied power cord to put the device into operation.
Use a suitable voltage supply cable to connect effect pedals or similar devices which require 24 V supply voltage at a maximum of 2000 mA to the out-put 1.
Use a suitable voltage supply cable to connect devices with high power consumption (i. e. multi-effect devices) which require 9 V supply voltage at a maximum of 3000 mA to the output 2.
Use suitable voltage supply cables to connect effect pedals or similar devices which require 9 V supply voltage at a maximum of 250 mA to the out-puts 3 – 4.
Use suitable voltage supply cables to connect effect pedals or similar devices which require 9 V supply voltage at a maximum of 500 mA to the outputs 5 – 7.
Danger of property damage by polarity reversal
Make sure that the polarity of the devices to be connected must be the same as the polarity of the power supply outputs power a device with polarity- reversed voltage may damage it!
Use suitable voltage supply cables to connect effect pedals or similar devices which require 9 V ,12 V or 18 V supply voltage at a maximum of 500 mA, 375 mA or 250 mA to the outputs 8 – 9. Set the associated switch above the output to the position of the required voltage. The maximum output power of 31.5 W must not be exceeded.
Danger of property damage by overvoltage
Make sure that connected devices are actually suitable for the set voltage. To power a device with overvoltage may damage it!
Use suitable voltage supply cables to connect devices as smartphones or tablets to the USB outputs.
Each operational output 1 – 9 is indicated by a green LED. If an output is switched off due to overload, the LED turns off. Then disconnect the pedal in question from the device. After approx. 2 seconds, the normal voltage supply is restored here.
To switch off the device, disconnect the power cord from the mains.

Technical specifications

Connections ( )

Output 1 24 V @ max. 2000 mA
Output 2 9 V @ max. 3000 mA
Outputs 3 – 4 9 V @ max. 250 mA (individually insulated)
Outputs 5 – 7 9 V @ max. 500 mA (individually insulated)
Outputs 8 – 9 switchable 9 / 12 / 18 V @ max. 500 / 375 / 250 mA (individually insulated)
USB output USB-C max. 18 W USB-A max. 18 W
Power output 31.5 W
Current output 2625 mA
Supply voltage 100 – 240 V ~ 50/60 Hz
Dimensions (W × H × D) 500 mm × 40 mm × 135 mm
Weight 1.0 kg
Ambient conditions Temperature range 0 °C…40°C
Relative humidity 20 %…80 % (non condensing)

For the transport and protective packaging, environmentally friendly materials have been chosen that can be supplied to normal recycling. Ensure that plastic bags, packaging, etc. are properly disposed of. Do not just dispose of these materials with your normal household waste, but make sure that they are collected for recycling. Please follow the notes and markings on the packaging.

This product is subject to the European Waste Electrical and Electronic Equip- ment Directive (WEEE) in its currently valid version. Do not dispose of your old device with your normal household waste. Dispose of this product through an approved waste disposal firm or through your local waste facility. Comply with the rules and regulations that apply in your country. If in doubt, consult your local waste disposal facility.

Thomann GmbH