tuya Smart 3MP 4CH Wireless NVR with 10 Screen Kit User Guide
- June 9, 2024
- Tuya
Table of Contents
Wireless NVR with 10 Screen Kit
User Guide
Statement
Thank you purchasing our products, if you have any questions or needs, please contact us. This manual applies to wireless network video recorder.
Attentions
- Please check when unpacking boxes, confirm the items and lists.
- Please don’t make the kit fall to ground or be hit bystrong forces.
- Please keep good ventilation environment around this product.
- Avoid installation in severe vibration environments.
- Please avoid environment with much humidity, dusextreme heat or extreme cold of the power supply carefully.
- Please avoid environment with much humidity, dusextreme heat or extreme cold of the power supply carefully.
- Please keep the product box to facilitate transfer orremoval of the equipment.
- Please make sure to turn off power of all items during installation. Check the voltage properly.
- Please contact the distributor or service center if the kit is damaged or not working.
Open-package inspection
After receive product, please open gift box then check accessories. If any
damage or lack,kindly please contact to the distributor.
Packing list
| S/N | Item | QTY |
|---|---|---|
| 1 | NVR Host | 1 |
| 2 | Type-C to DC and RJ45 adater | 1 |
| 3 | Support frame | 1 |
| 4 | USB Mouse | 1 |
| 5 | DC 12V@2A Power supply | 1 |
| 6 | Product user manuals | 1 |
| 7 | Wireless IP Camera | 8-Apr |
| 8 | DC 12V@1A Power supply | 8-Apr |
| 9 | Screw bag(4 screws for HDD) | 8-Apr |
Product description
4.1 Wireless Camera
| S/N | Item | Description |
|---|---|---|
| 1 | Antenna interface | Install antenna |
| 2 | Setscrew | Fixed bracket |
| 3 | Knob | Adjust the camera angle |
| 4 | Reset | Pair button |
| 5 | Power Supply | 12VDC power supply. |
4.2 Wireless NVR
Front view
back view
top view
Bottom view
| S/N | Item | Description |
|---|---|---|
| 1 | power light | Flashing light after power on |
| 2 | hanging hole | Mount the device on the wall |
| 3 | speaker | Play the sound captured by the camera |
| 4 | Support frame | Put the device on the table |
| 5 | hard drive cover | Open the cover to install the hard disk |
| 6 | screen switch | Touch to turn the screen on/off |
| 7 | Type-c interface | Plug in the power box |
| 8 | USB | Connect USB device |
4.3 Power box
Overall view
Port view
| 1 | Type-c | Access to NVR’s Type-c hole |
|---|---|---|
| 2 | Power light | Flashing light after power on |
| 3 | Power | 12VDC power supply. |
| 4 | Network light | Lights up when the network is connected |
| 5 | Network port | Access network cable |
Installation of device
Note:
- A factory recommended HDD should be installed befor power on.
- The maximum of hard disk capacity is 4TB.
5.1 Install HDD to NVR
-
Using a Phillips screwdriver, remove the top cover andinstall the hard drive.
-
Then put the 2.5″ SATA hard drive in
5.2 Cable Connection
Connect the wire as below diagram
Notes:
In order to guarantee the video quality, IPC antenna should try to keep in
parallel or tangent with NVR antenna. Because the signal of surrounding
antenna is much stronger ,but much weaker if antenna endpoints back off
direction.
Local Operation
6.1: Power on
Check the power supply is plugged into an electrical outlet,and turn on the
button.Then the power LED shouldred,and the video will automatic display on
the monitor, after several minutes.
6.2: Login
- Click right mouse button, log-in menu pops up.
- Enter the correct password, default password is admin.
Note: Please modify the user password before using the product to protect your
privacy.
Password modification: Main menu → The system menu → Account →Modify Pwd
6.3: Format the hard disk
- Right click to login and enter “Main menu→System →HDD manager”.
- Then click “Format Disk” button .
- The hard disk status would turn on “in use”.
6.4: Network configuration
- Conform network cable is connected to LAN correctly for access the internet.
- Enter into”Main menu→System→Network Config” menu.
- Select”DHCP”,and click “save” button,it”ll request IP address from the DHCP server automatically.
- The configuration is Sucessful,if the IP address is not 0.0.0.0.After refresh. Otherwise,please set the IP address and gateway information Manually.
Mobile Phone view
Step 1:Install software
Scanning the QR code in the user manual to download ,and install it.
-
Download QR code
https://smartapp.tuya.com/tuyaSmart -
Startup
Step 2: Tap “Register” button to register Account
Step3: Add device
After login,Tap “+” button in the main interface view to open the device
adding view.
Step 3:Live view
Tap the online device icon in the device list, the channel’s video will be
connected and display automatically.
| Icon | description | Icon | description |
|---|---|---|---|
| Device info and share | Multi-screen | ||
| Alarm info list | Snap | ||
| Playback on device | Talk | ||
| Cloud Record | Record | ||
| Channel Setting | SD/HD |
Other oparetion
8.1 Video playback
Steps:Right click to select playback → login→ select singal or multi channel
playback mode →select channel →select date →double click to start play record.
8.2 Video backup
Steps:Insert U disk to USB interface→Right click to select Main
menu→login→select backup→select channel→set starting time and ending
time→click. Search”button→select the record→select or create new file→click
“Backup” button to backup record.
8.3 Add camera
Add or replace wireless camera,please fellow the steps below.
a) Wait 1 minutes for camera start up.
b) Enter ”Main menu→Pair IPC” window, →delete not connected camera → Click
”Pair” button, pop-up a textbar →Push the pair button in IPC within 5 seconds.
pair successfully when dispaly “connected” in status column.c) Repeat step c
and d, then click [OK] button to finish.
Tuya download QR code
https://smartapp.tuya.com/tuyaSmart