robustel R3000 Lite IoT VPN 4G Cellular Gateway Router User Manual

: June 9, 2024
: robustel

robustel R3000 Lite IoT VPN 4G Cellular Gateway Router User Manual

Regulatory and Type Approval Information Table 1: Directives

2011/65/EC| The European RoHS 2011/65/EU Directive was issued by the European parliament and the European Council on 1 July 2011 on the restriction of the use of certain Hazardous substances in electrical and electronic equipment.
---|---
On June 4, 2015, the Official Journal of the European Union published the RoHS2.0 Amendment Directive (EU)

In 2015/863, four phthalates (DEHP, BBP, DBP, DIBP) were officially included in the list of restricted substances in Appendix II of RoHS 2.0 (2011/65/EU).

From July 22, 2019, all electronic and electrical products exported to Europe (except medical and monitoring equipment) must meet this restriction; from July 22, 2021, medical equipment and

monitoring equipment will also be included in the scope of control.

2012/19/EU| The European WEEE 2012/19/EU Directive was issued by the European parliament and the European Council on 24 July 2012 on waste electrical and electronic equipm

Table 2: Toxic or Hazardous Substances or Elements with Defined Concentration Limits

Name of the Part	Hazardous Substances
(Pb)	(Hg)
Metal parts	o
Circuit modules	o
Cables and cable assemblies	o
Plastic and polymeric parts	o

o:

Indicates that this toxic or hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in 2011/65/EU and SJ/T11363-2006.

x:

Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials for this part might exceed the limit requirement in 2011/65/EU and SJ/T11363-2006.

Radio Specifications

RF technologies	2G, 3G, 4G
4G: LTE FDD: B1/B2/B3/B4/B5/B7/B8/B28
LTE TDD: B40	Oceania
3G: WCDMA: B1/B2/B5/B8	South America
2G: GSM: B2/B3/B5/B8

Cellular Frequency*

| 4G: LTE FDD: B2/B4/B5/B13/B17

3G: UMTS: B2/B5

| USA
| 4G: LTE FDD: B1/B3/B5/B7/B8/B20|
| LTE TDD: B38/B40/B41

3G: WCDMA: B1/B5/B8

3G: WCDMA: B1/B2/B4/B5/B6/B8/B19

2G: GSM: B2/B3/B5/B8

|
---|---|---
4G: LTE FDD: B1/B3/B8/B18/B19/B26 LTE TDD: B41

3G: WCDMA: B1/B6/B8/B19

| ****

Japan

4G: LTE FDD: B1/B3/B7/B8/B20/B28A

3G: WCDMA: B1/B8

2G: GSM: B3/B8

| ****

EMEA

Max RF power| 35 dBm@GSM, 25 dBm@WCDMA, 25.7 dBm@LTE

* May vary on difference models.

Simplified EU Declaration of Conformity

We, Guangzhou Robustel Co., Ltd. are located at 501, Building #2, 63 Yongan Road, Huangpu District, Guangzhou, China, declare that this radio equipment complies with all applicable EU directives. The full text of the EU DoC is available at the following internet address:

www.robustel.com/certifications/

FCC Declaration of Conformity

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful
This device must accept any interference received, including interference that may cause undesired

IC Declaration of Conformity

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause
This device must accept any interference, including interference that may cause undesired operation of the

Radio Frequency Exposure Statement for IC

This device complies with IC exposure limits set forth for an uncontrolled environment. This device shall be installed and operated with minimum distance 20cm between the radiator & body.

Find more product documents or tools at: www.robustel.com/en/documentations/

Technical Support

Tel: +86-20-82321505

Email: support@robustel.com Web: www.robustel.com

[ ](https://manuals.plus/wp-content/uploads/2023/01/robustel-R3000-Lite-

IoT-VPN-4G-Cellular-Gateway-Router-User-Manual_1.jpg)Document History

Updates between document versions are cumulative. Therefore, the latest document version contains all updates made to previous versions

Date| Firmware Version| Document Version| Change Description
---|---|---|---
July 28, 2022| 5.0.0| 1.0.0| Initial release.
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |

Overview

The Robustel Industrial Dual SIM Cellular VPN Router (R3000 Lite) is a rugged cellular router offering
state-of-the-art mobile connectivity for machine to machine (M2M) applications. R3000 Lite is a powerful router developed from RobustOS, a Robustel self-developed and Linux-based operating system which is designed to be used in Robustel hardware routers.

Package Checklist

Before commencing installation ensure your package has the following components:

Panel Layout (May Vary on Different Models

Interface Descriptions

1 .LED

Name	Color	Status	Description
RUN	Green	On, fast blinking

(250ms blink time)

| Router is powered on (System is initializing)
On, blinking

(500ms blink time)

| Router starts operating
Off| Router is powered off

USR-SIM

| ****

Green

standard

Blinking: 1 Off: 0 bit2 bit1 bit0

0 0 1 AT command failed

0 1 0 no SIM card detected

0 1 1 need to enter the PIN code

1 0 0 need to enter the PUK code

1 0 1 registration failed

1 1 0 module error

1 1 1 not support the module

Note: You can choose the display type of USR LED. For more details, please refer to
_RT123_SMRobustOS Software Manual Service > Advanced > System >System Settings > User LED Type.

2. USB Interface.

Function	Operation
Firmware upgrade	USB interface is used for batch firmware upgrading, but

cannot be used for sending or receiving data from slave devices which connected to it. You can insert a USB storage device into the router’s USB interface, such as a U disk or a hard disk. If there have a supported configuration file or a router firmware in this USB storage device, the router will automatically update the

configuration file or the firmware. For more details, see _RT123_SMRobustOS Software Manual.

3. PIN Assignment

PIN	Debug (232)	RS-232	RS485 (2 Line)	Direction
1			Data+(A)	—
2		RXD		Router→Device
3		TXD		Router←Device
4	DRXD			Router←Device
5	GND	GND	GND
6			Data-(B)	—
7		RTS		Router←Device
8		CTS		Router→Device
9	DTXD			Router→Device

4. Reset Button

Function	Operation
Reboot	Press and hold the RST button for 2~ 5 seconds under the operating

status.
Restore to default

configuration

| Press and hold the RST button for 5~10 seconds, the RUN LED starts blinking quickly, the router will restore to default

configuration.

Restore to factory

default settings

| Once the operation of restoring default configuration is performed twice within one minute, the router will restore to factory

default settings.

Note: The more details please refer to _RT123_SMRobustOS Software Manual, 2.3 Factory Reset.

5. Ethernet Ports. R3000 Lite Router has one Ethernet port with two LED indicators. The yellow one is link indicator
and the green one is speed indicator. For details about status, see the table below.

Indicator	Status	Description
Link indicator	On, solid	Connection is established
On, blinking	Data is being transferred
Off	Connection is not established
Speed indicator	On, solid	100 Mbps mode
Off	10 Mbps mode

Hardware Installation

SIM Card Installation. Loosen the screws associated with the cover by using a screwdriver and then find the SIM card slot. Press the card with finger until you hear a click and then tighten the screws associated with the cover by using a screwdriver. Put back the cover and tighten the screws associated with the cover by using a screwdriver
Antenna Installation. Rotate the antenna into the antenna connector accordingly
Mounting Kit installation. (Optional) Wall mountin
Power Supply installation. Following to the color of the head, connect the cable marked red to the positive pole through a terminal block, and connect the yellow one to the negative in the same way.
Note: The range of power voltage is 9 to 36V DC.
Connect the Router to a Computer. Connect an Ethernet cable to the port marked ETH at the bottom of the R3000 Lite, and connect the other end of the cable to your computer.

Connect the router’s Ethernet port to a PC with a standard Ethernet cable.
Before logging in, manually configure the PC with a static IP address on the same subnet as the gateway address, click and configure “Use the following IP address”.
To enter the gateway’s web interface, type http://192.168.0.1 into the URL field of yourInternet browser.
Use login information shown in the product label when prompted for authentication
After logging in, the home page of the web interface is displayed, then you can view system information and perform configuration on the device.
The automatic APN selection is ON by default, if need to specify your own APN, please go to themenu Interface->Link Manager->Link Setting->WWAN Settings to finish the specific setting.
The more configuration details please refer to RT123_SM_RobustOS Software Manual. (END)