FURNIWELL 20230213 47 Inch L Shaped Sit Stand Desk Installation Guide
- May 15, 2024
- Furniwell
Table of Contents
INSTALLATION MANUAL
ELECTRIC
SIT-STAND DESK
min 730mm, max 1180mm 80kg(176lbs)
Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact our online after-sale service for help.
CAUTION: Use with products heavier than the rated weights indicated may result in instability causing possible injury.
- Mounts must be attached as specified in assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installation. If any parts are missing or faulty, please contact our online after-sale service for help.
MAINTENANCE: Check that the bracket is secure and safe to use at regular intervals (at least every three months).
B1(X1) B2(X1) B3(X1) B4(X1) B5(X1)
B6(X2) B7(X1) B8(X1)
B9(X1) B10(X1)
B11(X2) B12(X2) B13(X2) B14(X1) B15(X1)
ax4 bx4 cx8 dx18 ex8 fx4
gx8
M6X10 M8X16 M6X35 M6X14 M6X40 M6X12 D8X40
hx2 ix1 jx5
M4 M5 M15
1
2
3
4
5
6
7
8
9
1 2
10
1 2 3
11
Digital Control Panel For
Electric Height Adjustable Desk
User Guide
Lifting Function:
Press “ ” button, the desk will rise and stop automatically when it rises
to the highest point.
Press “ ” button, the desk will descend and stop automatically when it
descends to the lowest point.
Release the button and the desktop stops the current action.
Preset Memory Height Function:
Long press the digit “ ” button for 3 seconds, and “S-1” is displayed,
indicating that the current height is saved to the “ ” button successfully.
The same operation to digit “ ” button.
Recall Memory Height Function:
Short press the digit “ ” button to recall its corresponding height and
automatically run the desktop to this height. The same operation to digit “ ”
button.
Desktop Reset:
When “ER1” is displayed or the desktop is at the lower limit position,
press and hold the “ ” button for more than 3 seconds until “RST” is displayed
and release the button. At this time, the system has entered the reset
preparation state. Press and hold the “ ” button again, the desktop begins to
descend to the bottom of the machine and rebound to a certain height. After
reset, the lowest height is displayed, and then release the “ ” button.
Child Safety Lock:
Press and hold the “ ” buttons for more than 5 seconds to set the child
safety lock. After the setting is successful, “ LOC ” will be displayed.
At this time, all key operations are invalid, but the child lock can still be
cancelled by pressing and holding the “ ” button for more than 5 seconds.
Anti-Collision Detection:
An advanced feature that helps you stop your desk from moving and reverse
its movement slightly when the desk touches something.
Overheat Protection:
“ hot ” is displayed. If the desktop continuously rises and descends
too frequently, desk motor will overheat. In order to avoid damage to the desk
motor, desk’s height adjustment will be disable for around 18 minutes.
Motor Abnormal Protection:
When “ ER1 ” is displayed, please power off first, check and ensure
that the connection between the motor and the controller is reliable, then
power on again and start reset procedure.
Setup Menu:
Long press “ ” button for 20 seconds, and the system enters the setup menu
with 7 settings available to choose from:
- Set minimum height: The foot length within desk’s adjustment range is 1 cm, and desk’s minimum height shall be at least 10 cm shorter than its maximum height.
- Set maximum height: The foot length within desk’s adjustment range is 1 cm, and desk’s maximum height shall be at least 10 cm taller than its minimum height.
- Sensitivity setting for anti-collision protection (upward adjustment): ranging from U-0 to U-9, where U-0 represents the protection disabled and U-9 represents the maximum sensitivity.
- Sensitivity setting for anti-collision protection (downward adjustment): ranging from d-0 to d-9, where d-0 rep-resents the protection disabled and d-9 represents the maximum sensitivity.
- Display settings (decimal point): F-0 represents the height value will not be displayed with the decimal point, while F-1 represents it will.
- Display settings (unit system): L-0 represents desk height in metric system, and L-1 represents it in imperial system with the decimal point displayed.
You may press and hold “ ” shortly to switch between the 7 settings; press on “ ” or “ ” to perform settings respectively; press and hold “ ” for no less than 5 seconds until the “ ” is displayed to have current setting saved.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>