SONOFF L3 RGB / L3-P Smart LED Strip Lights User Manual

SONOFF L3 RGB / L3-P Smart LED Strip Lights

Controller Introduction

Button features

Short press: Turn on/off the strip light
Long press for 5s: Make strip light enter in the pairing mode (LED indicator flashes)
Short press the button to exit the pairing mode while it is in the pairing mode.

Features

L3&L3 Pro both are smart strip lights, which have 16 million colors and support switching various scene modes through your smartphone or voice control. Also, you can select different modes based on the music styles to sync the music with gorgeous lighting.

App Control

|

Voice Control

---|---

Timer Schedule

|

Share Control

Dimming

|

Music Reactive Mode

16M Colors

|

Group Control

Bluetooth Control

|

Scenes Mode

Operation instruction

1. Clean the surface
   

2. Peel off the protective film
   

3. Stick it on
   

4. Download the eWeLinkApp
   |
   ---|---
   
   

5. Power on
   
   Power on the LED strip light with a Type-C USB cable, after powering on, it will enter the Bluetooth pairing mode by default and flashes.
   
   The strip lights will exit the Bluetooth pairing mode if it not be paired within 3 mins. If you want to enter this mode again, please long press the controller for 5s until the strip lights “flashes” then release.

6. Add light strip
   
   Tap”+” and select “Bluetooth Pairing”, then operate following the prompt on the App.

Wi-Fi Settings

• Select the “Wi-Fi Settings” on the “Device Settings” interface in the eWeLink App to add or change the network.
  

When Wi-Fi is disconnected, the device will automatically switch to Bluetooth control (Ensure Bluetooth is enabled on your mobile phone).

Specifications

Models : L3-5M, L3-5M-P

Light Strips

Controller

Cuttable

• L3 : Cutable every 55.55mm
  

• L3 Pro : Cutable every 33.33mm
  

Please note that the light strips cannot be restored if you cut it.

Factory Reset

Deleting the device on the eWelinkApp indicates you restore it to factory setting.

Safety Warning

1. Before use, please confirm that the voltage is appropriate for this product’s working voltage. Using inappropriate voltage may damage the product and bring safety hazards.
2. LED Light Sources are unchangeable, please don’t dismantle them.
3. The Strip Lights will generate heat during working, please keep air circulation for heat dissipation.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note :
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Hereby, Shenzhen Son off Technologies Co., Ltd. declares that the radio equipment type L3-5M/L3-5M-P are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address:
https://sonoff.tech/usermanuaIs

Customer Support

Shenzhen SonoffTechnologies Co., Ltd.
3F & 6F, Bldg A, No. 663, Bu long Rd, Shenzhen, Guangdong, China
ZIP code : 518000 Website : sonoff.tech

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>