BRILONER 10573351 18W LED Ceiling Light Instruction Manual
- June 4, 2024
- BRILONER
Table of Contents
BRILONER 10573351 18W LED Ceiling Light
Mounting instructions
**Safety directions / Please read this information carefully before
installing or using this product. Please keep this user manual for further
reference.
**
-
The lamps may only be installed by authorized and qualified technicians according the valid regulations for electrical installation.
-
The manufacturer does not accept any responsibility for injuries or damage resulting from improper use of the light.
-
Maintenance of the lights is limited to the surfaces. For electrical safety reasons, this product must not be cleaned with water or other liquids. Use only a dry, lint-free cloth for cleaning.
-
Caution! Risk of electric shock. Before connecting to the mains, always check the entire light for possible damage. Never use the light if you notice any damage.
-
Caution! Disconnect the mains cable from the power supply before assembling or disassembling. Switch off the earth leakage circuit breaker/automatic circuit breaker or unscrew the fuse. Turn the switches to “OFF”.
-
Caution! Before drilling the mounting holes, make sure that no gas, water or electricity pipes and wires can be drilled through or damaged in your chosen mounting location.
-
When mounting, ensure that the attachment material is suitable for the subsurface and that this surface is capable of carrying the weight of the fixture. The manufacturer is not liable for improper installation of the item on the relevant subsurface.
-
The symbol of the crossed-out garbage can on the product or the packaging means that the product must not be disposed with ordinary household waste. At the end of its useful life, the product must be returned to a point of acceptance for the recycling of electric and electronic device. Please ask your local municipality for the point of acceptance.
-
Safety class I G. This light must be connected to the earthed conductor-terminal with the earthed conductor (green-yellow wire) G.
-
Description of the supply terminals: L = Phase N = Neutral conductor G = Earthed conductor.
-
Protective covers and end covers for mains voltage control parts must always be mounted.
-
Do not install the light on a damp or conductive subsurface.
-
Please make sure that no cables get damaged during the installation work.
-
Attention! During operation, lamp parts and illuminants can reach temperatures of more than 60°C. Do not touch during operation!
-
Only the included individual parts may be used; otherwise any and all guarantee claims will expire.
-
The lights have a protection class rating of “IP20“ and are solely intended for indoor use only of private households.
-
Do not look directly into the light source (illuminant, LED, etc.).
-
The included or insertable LED light bulb contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
-
This product contains a light source of energy efficiency class „E“, based on the EU regulation 2019/2015.
-
LED colour deviation when using different chargers may occur. The light colour and luminous strength of the LED’s can also change as a result of life span level from the lamp.
-
This article is not suitable for use with dimmable electric circuits. It can be controlled using the accompanying remote control.
-
Lamp with remote control (The lights can only be switched on by remote control when there is no obstruction between the remote control and the lights.) Available functions of the product:
-
The “ON/OFF” button switches the lights on with the last switch position to have been used. The “ON/OFF” button switches the lights off.
-
The “WW/NW/CW“ button consecutively switches through the adjustable colour temperature range from “3000K” to “6500K”.
-
The “Timer” button switches the lights off after “30” minutes. The operation is confirmed by the flashing of the LED´s (1x).
-
The “Bright” and “Dim” buttons brighten and dim the lights either in stages or continuously.
-
The “Cool” and “Warm” buttons move the colour temperature closer to cool white or warm white either in stages or continuously.
-
The “Night Light” button switches the lights to their dimmest setting with a colour temperature of approximately “3000K”.
-
The “20% 50% 100%“ button switches the lamp to a dimming level of “20% 50% 100%”.
-
The “3000K“ button switches the lamp to a colour temperature of “3000K”. The “4000K“ button switches the lamp to a colour temperature of “4000K”. The
“6500K“ button switches the lamp to a colour temperature of “6500K”. -
This light is fitted with an electronic changeover switch. This means that the colour temperature of the lamp is controlled by switching the power supply on and off.
- 1 x on → It will be switched to a colour temperature of “6500K (3000K / 4000K / Night Light)”. b. 1 x off and within 1 sec. on again → It will be switched to a colour temperature of “3000K (4000K / Night Light / 6500K)”. c. 1 x off and within 1 sec. on again→ It will be switched to a colour temperature of “4000K (Night Light / 6500K / 3000K)”. d. 1 x off and within 1 sec. on again→ It will be switched to a colour temperature of “Night Light (6500K / 3000K / 4000K)”. e. Further switching on and off of the lamp means having to run through the individual stages again. It generally does not matter how the lamp is switched on (circuit-breaker, multi-switch connection or cross circuit). Essential for operation is the connection and disconnection of the lamp from the power supply.
-
memory function: The lamp is switched on using an external light switch after a minimum off period of approx. “5” seconds with the last selected function or switch position.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>