BRILONER MAL 7999 C Leuchten 799 9046 Set of 4 Recessed Ceiling Lights User Manual

June 15, 2024
BRILONER

Mounting instructions
MAL 7999

MAL 7999 C Leuchten 799 9046 Set of 4 Recessed Ceiling Lights

BRILONER MAL 7999 C Leuchten 799 9046 Set of 4 Recessed Ceiling
Lights

Safety directions

Please read this information carefully before installing or using this product. Please keep this user manual for further reference.

  1. The lamps may only be installed by authorized and qualified technicians according the valid regulations for electrical installation.

  2. The manufacturer does not accept any responsibility for injuries or damage resulting from improper use of the light.

  3. Maintenance of the lights is limited to the surfaces. When doing this, no moisture must come into contact with any areas of the terminal connections or mains voltage control parts.

  4. Attention! Before starting the installation work, make sure that the mains power line is voltage-free – turn off safety cutout or unscrew the protection fuse. The switch must be “OFF”.

  5. Warning! Before drilling the mounting holes, make sure that no gas, water or electricity pipes and wires can be drilled through or damaged in your chosen mounting location.

  6. **** The symbol of the crossed-out garbage can on the product or the packaging means that the product must not be disposed with ordinary household waste. At the end of its useful life, the product must be returned to a point of acceptance for the recycling of electric and electronic device. Please ask your local municipality for the point of acceptance.

  7. Safety class II Icon. This light is specially insulated and must not be connected to an earthed conductor.

  8. Description of the supply terminals: L = Phase N = Neutral conductor ****= Earthed conductor.

  9. This product is designed for direct wiring to the mains “230 V / 50 Hz”.

  10. The lamp does not have a connecting terminal. An electrician may need to be consulted to connect the lamp.

  11. You can use the following connectors (not included in delivery):
    2 screwless connectors in accordance with EN 60998-2-2 (min. 2 pole with retention clip – e.g. “WAGO series 221 / 222“) designed for a cross-section of 0.5 mm² – 1.5 mm² with a rated voltage of min. 250 V and a rated current of min. 16 A.
    The free cable ends of the light must be provided with ferrules depending on the design of the connectors.
    The connection to the power network must take place within a sufficiently large enough standard junction box per light (not included in delivery).

  12. Do not install the light on a damp or conductive subsurface.

  13. Please make sure that no cables get damaged during the installation work.

  14. Attention! During operation, lamp parts and illuminants can reach temperatures of more than 60°C. Do not touch during operation!

  15. The lights have a protection class rating of “IP44“ and are solely intended for indoor use only of private households.

  16. The protection class “IP44” only applies to the visual area of the lamp when installed. IP degree of protection applies for ceiling suspension only.

  17. The protection class “IP20” applies to the concealed area of the lamp when installed.

  18. To comply with the IP protection class rating, the lights may only be mounted on flat surfaces.

  19. Do not look directly into the light source (illuminant, LED, etc.).

  20. The light source of this lamp is not replaceable. If the light source has reached the end of its operational life, the entire lamp must be replaced.

  21. This product contains a light source of energy efficiency class “F“, based on the EU regulation 2019/2015.

  22. LED colour deviation when using different chargers may occur. The light colour and luminous strength of the LED’s can also change as a result of life span level from the lamp.

  23. Y This article is not suitable for use with dimmable electric circuits. It can be dimmed to “3“ different levels by repeatedly switching on and off.

  24. Memory function: Switching on the light using an external light switch after a minimum switch-off time of approx. “5“ seconds does the following: The last selected dimmer setting will be switched on again.

  25. Never cover these lamps with heat-insulating enclosures or similar materials.

MAL7999 Page3b

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals