Munters E-LINE Air Extraction Fan Installation Guide
- June 5, 2024
- Munters
Table of Contents
Air extraction fan
Saturn FIVE High Efficiency
AM_SaturnFIVE_202403_Multi
P/N 2200221
Assembly instructions
Saturn FIVE High Efficiency
MOTOR POWER: 1,5 HP
MODEL: BELT DRIVE TRASMISSION
PROPELLER: 3 BLADES
Saturn FIVE High Pressure
MOTOR POWER: 2 HP
MODEL: BELT DRIVE TRASMISSION
PROPELLER: 6 BLADES
Saturn FIVE Direct Drive
MOTOR POWER: 2 HP
MODEL: DIRECT DRIVE
PROPELLER: 3-5 BLADES
Saturn FIVE Electronically Commutated
MOTOR POWER: 3 Hp
MODEL: E-LINE
PROPELLER: 3-5 BLADES
Tools
| Screwdriver
---|---
| 10Mm Spanner
| 32Mm Spanner
| 8Mm Spanner
| 13Mm
Combination Spanner
| 8Mm
Combination Spanner
| Torque wrench
| Inserting Machine
| Philips Drive Bit
| Long Spanner Adapter
| Drill bit Ø 13mm
| Riveting Machine
| Allen key 6mm
| Pliers
| Support (H=4Cm Min)
Bolt & Nut
| HE| HP| DD| EC| HE-WM| HP-WM| DD-WM|
EC-WM
---|---|---|---|---|---|---|---|---
M6x30 Hex Screw| 4| 4| 0| 0| 4| 4| 0| 0
M8x20 Hex Screw| 0| 0| 0| 4| 0| 0| 0| 4
M8x25 Hex Screw W/Flange| 36| 36| 32| 32| 36| 36| 32| 32
M8x50 Hex Screw| 47| 47| 45| 45| 45| 45| 43| 43
M8x65 Hex Screw| 24| 24| 24| 24| 24| 24| 24| 24
Ø6.3×19 Self-Tapping Screw| 1| 1| 0| 0| 1| 1| 0| 0
M8x30 Allen screw| 7| 7| 7| 7| 7| 7| 7| 7
M10x25 Hex Screw| 0| 0| 1| 1| 0| 0| 1| 1
M10x50 Hex Screw| 0| 0| 4| 0| 0| 0| 4| 0
M25 Hex Nut| 1| 1| 0| 0| 1| 1| 0| 0
M6 Hex Nut W/Flange| 4| 4| 0| 0| 4| 4| 0| 0
M8 Hex Nut| 4| 4| 0| 0| 4| 4| 0| 0
M8 Hex Nut W/Flange| 103| 103| 101| 101| 101| 101| 99| 99
M10 Hex Nut| 0| 0| 4| 0| 0| 0| 4| 0
Ø8 Toothed Washer| 4| 4| 0| 4| 4| 4| 0| 4
Ø6×24 Washer| 17| 17| 16| 16| 17| 17| 16| 16
Ø8×24 Washer| 33| 33| 37| 37| 31| 31| 35| 35
Ø8×32 Washer| 24| 24| 24| 24| 24| 24| 24| 24
Ø10×20 Washer| 0| 0| 8| 0| 0| 0| 8| 0
Ø17×30 Washer| 6| 6| 6| 6| 6| 6| 6| 6
Ø10×40 Washer| 0| 0| 1| 2| 0| 0| 1| 2
Ø10 Spring washer| 0| 0| 1| 1| 0| 0| 1| 1
Ø4.8×9 Pop Up Rivet| 28| 28| 28| 28| 28| 28| 28| 28
Ø6.4×12 Pop Up Rivet| 34| 34| 34| 34| 24| 24| 24| 24
M8x17.5 Threaded Bush| 7| 7| 7| 7| 7| 7| 7| 7
BODY AND MOTOR ASSEMBLY
Op.01 Superstructure Assembly
Tools Bolts & Nuts
Tools Bolts & Nuts
Tools Bolts & Nuts
Op.02 Hub assembly
Tools Bolts & Nuts
Op.03 Hub fixing on structure
Tools
Bolts &
Nuts
Op.04 Conveyor assembly
Op.05 Conveyor fixing on structure
Tools Bolts & Nuts
Op.06 Reinforcement bracket fixing
Tools Bolts & Nuts
Op.07 Panel assembly
Tools Bolts & Nuts
Op.08 Panel assembly
Tools Bolts & Nuts
Op.09 Panel assembly
Tools Bolts & Nuts
Op.10 Angle Brackets Mounting
Tools Bolts & Nuts
Op.11 Panel assembly
Tools Bolts & Nuts
Op.07 Panel assembly (WallMount)
Tools Bolts & Nuts
Op.08 Panel assembly (WallMount)
Tools Bolts & Nuts
Op.09 Panel assembly (WallMount)
Tools Bolts & Nuts
Op.10 Angle Brackets Mounting (WallMount)
Tools Bolts & Nuts
Op.11 Panel assembly (WallMount)
Tools Bolts & Nuts
Op.12 Assembly of motor supports
Tools Bolts & Nuts
Op.13 Motor Mounting
Tools Bolts & Nuts
Tools Bolts & Nuts
Tools Bolts & Nuts
Op.14 Condensate drain and fairlead
Tools
Perforate the conveyor only if necessary.
Use caUtion when breaking marked Part.
Op.15 Transmission belt mounting
Tools Bolts & Nuts
Place v-belt (1) on the pulleys (2) and (3) and then rotate the propeller
clockwise in order to tighten the v-belt on the pulleys.
Check tensioning: right tensioning is obtained when tension over the v-belt
corresponds to a resonance frequency of 60±2 Hz measured by a v-belt tension
meter like the “Trummy 2” manufactured by Fag or the “Ten-Sit” manufactured by
Sit.
Op.16 Fan mounting
Tools Bolts & Nuts
Tools Bolts & Nuts
Tools Bolts & Nuts
Tools Bolts & Nuts
BUTTERFLY ASSEMBLY AND INSTALLATION
Op.17 Magnet unit assembly
Op.18 Ring assembly
Op.19 Ring assembly
Tools Bolts & Nuts
Op.20 Magnet unit installation
Tools Bolts & Nuts
Op.21 Magnet unit installation
Tools Bolts & Nuts
Op.22 Ring installation
Tools Bolts & Nuts
Procedure following wall installation of the fan.
Op.23 Door assembly
Op.24 Door assembly
Tools Bolts & Nuts
Op.25 Door assembly
Tools Bolts & Nuts
Op.26 Butterfly mounting on Fan
Tools Bolts & Nuts
Op.27 Butterfly mounting on Fan
Tools Bolts & Nuts
Op.28 Butterfly springs mounting
Tools Bolts & Nuts
Op.29 Butterfly springs mounting
Tools Bolts & Nuts
ASSEMBLY OF AIR EXTRACTION CONE UNIT
Op.30 Cone Mounting
Tools Bolts & Nuts
Op.31 Cone Mounting
Tools Bolts & Nuts
Op.32 Cone Mounting
Op.33 Cone Mounting
Tools Bolts & Nuts
Op.34 Mounting of cone protection grille
Tools Bolts & Nuts
AIR EXHAUST CONE ASSEMBLY INSTALLATION
Op.35 Cone installation on fan
Tools Bolts & Nuts
Procedure following wall installation of the fan.
INTERNAL PROTECTION GRID MOUNTING
Op.36 Internal protection grid mounting
Tools Bolts & Nuts
For production or other reasons, after publication © Munters AB, 20200 reserves the right to make changes to specifications, quantities, etc.
Munters Italy S.p.A
Strada Piani, 12
18027 Chiusavecchia (IM), Italy
Tel: +39 0183 52 11
Fax: +39 0183 521 333
email:info@munters.it
www.munters.com
AM_SaturnFIVE_202403_Multi
P/N 2200221
Documents / Resources
|
Munters E-LINE Air Extraction
Fan
[pdf] Installation Guide
E-LINE Air Extraction Fan, E-LINE, Air Extraction Fan, Extraction Fan, Fan
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>