Numatic NBV190 Battery Powered Vacuum Cleaner User Manual

: June 9, 2024
: Numatic

Numatic NBV190 Battery Powered Vacuum Cleaner

Kit AS55

Assembly

Floor tool adjustment

Using the machine

Charging your battery

For information relating to the operation and charging of your battery please refer to the battery and charger original operating instructions

Battery Status

Cleaning your machine

Tool Tidy

NBV Wand Docking

PBT 230

Fitting the Face

Removing the Face

Data

NBV190| Voltage| Power Rating| Airflow| *Run time| Size
---|---|---|---|---|---
36 V (DC)| 350 W / 200 W| HI = 22.0 L/sec LO = 17.0 L/sec|

HI = 49 Mins
LO = 83 Mins

Charge time

NBV190| 7.7 kg| NVM-1CH| 8 L|

1hr to 80% charge – fast charger
2hrs to 100% charge – fast charger 4.5hrs to 100% charge – slow charger

NBV240| 8.1 kg| 9 L
PBT 230| 10.5 kg| 9 L
Sound Pressure|

Run and Recharge times may vary dependent on ambient temperature.

LpA ≤ 70 dB(A)

About your machine

Rating Labe

1	Voltage / Direct Current
2	Rated input power
3	Weight (ready to work)
4	Company name & address
5	Model
6	Machine yr/wk Serial number
7	Approval Mark
8	WEEE Logo
9	Use Lithium-Ion Battery Only

PPE (personal protective equipment) That may be required for certain operations.

| | | |
---|---|---|---|---
Ear Protection| Safety Footwear| Head Protection| Safety Gloves
| | |
Eye Protection| Protective Clothing| Dust / Allergens Protection| Hi Viz Jacket| Caution Floor Sign

Note: A risk assessment should be conducted to determine which PPE should be worn.

WEEE Legislation (Waste, Electrical and Electronic Equipment)

Vacuum cleaner, accessories and packaging should be sorted for environmentally – friendly recycling.
(Only for EU Countries) Do not dispose of vacuum cleaner into household waste! According to the
European Directive 2012/19/EU on waste electrical and electronic equipment and its incorporation into national law
Vacuum cleaners that are no longer suitable for use must be separately collected and sent for recovery in an environmentally – friendly manner.

Failure to rectify the problem or in the event of a breakdown contact your Numatic dealer or the Numatic Technical helpline +44 (0)1460 269268

Daily
Keep the machine clean, including hoses and tubes.
Ensure the bag and fi lter are fi tted.
Regularly examine the charger.
Check dust bag frequently.
Check fi lters are clean.
Weekly – as daily and:-
Check for any worn or damaged parts and replace immediately.
Do not steam clean or pressure wash.
Batteries
Always recharge the batteries after use.
Safety Critical Components
Multi-Regional Charger (100-240V ~ 50/60 Hz) Lithium- Ion Battery 5.2Ah

Information for DRY use Vacuum cleaners

WARNING!

Read the instruction manual before using the machine. Operators shall be adequately instructed on the use of these machines, as with all electrical equipment, care and attention must be exercised at all times during use, you must also make certain that routine and preventative maintenance is carried out periodically to ensure safe operation. Failure to carry out maintenance as necessary, including the replacement of parts to the correct standard could render this equipment unsafe and the manufacturer can accept no responsibility in this respect.
This machine is for DRY USE only. You must remove the battery from the machine BEFORE cleaning or maintenance and when replacing parts or converting the machine to another function. This appliance is intended to be assembled, cleaned and maintained by an adult. This machine is not suitable for the collection of biological hazards, hazardous or explosive dusts.
Contact your local distributor if you require a machine capable of performing these tasks.
The machine must not to be used by persons with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction. This machine is not a toy; children shall not play with this machine.

CAUTION

This machine must not be stored outside, or used in wet environments, or to collect wet materials.
The vacuum cleaner should be stored in a dry place and is for indoor use only.
You must ensure that the filtration system fitted to the machine is suitable for the material being collected.

NOTES

This machine is also suitable for commercial use, for example in hotels, schools, hospitals, factories, shops, rental businesses and offi ces for other than normal housekeeping purposes.
This product complies with the requirements of clause 20 of IEC/EN 60335-2-69 Stability and Mechanical Hazards.
This vacuum cleaner is fi tted with a thermal protection device. If the vacuum cleaner stops
working, remove the plug from the wall before investigating where the fault lies.
If the vacuum cleaner has a blockage, switch off , remove the plug from the socket, inspect the fl oor tool, tubes and hose for debris. If the fl oor tool, tubes and hose are clear, replace the dust bag and clean the fi lter.
The vacuum cleaner should be inspected after use for damage. The vacuum cleaner should be stored in a dry place.

DO

Keep your machine clean including hoses and tubes.
Change dust bag frequently.
Keep fi lters clean.
Keep diff user fi lter (where fi tted) clean.
Use fi lter bags, they will enhance performance and help keep machine clean.
Use a Numatic Original fi lter bag under fi ne dust conditions.
Keep hoses and tubes clear.
Replace any worn or damaged parts immediately.
Only use the socket outlet on the machine for purposes specifi ed in the instructions.
Only use the brushes provided with the machine. The use of other brushes may impair safety.
Regularly examine the power cord. If damage is found such as cracking or ageing the power cord must be replaced by a qualifi ed person.
Only replace the power cord with the correct Numatic approved replacement part.

DO NOT

Pull on the cable to unplug the machine from the power supply.
Use to suck up hot ashes or lighted cigarette ends.
Use steam cleaners or pressure washers to clean the machine or use in the rain.
Immerse in water for cleaning.
Attempt machine maintenance or cleaning unless the power supply plug has been removed from the supply outlet.
Use in wet environments or to collect wet materials.
Under any circumstances place foreign objects including (but not limited to) air fresheners, air freshener capsules or scented beads of any type into the top fi lter of the machine. Doing so can be dangerous and risk damage to the machine and may invalidate the machine w

Information Warnings – Batteries

Read all the warnings before using the battery.

The battery is equipped with electronic thermal protection, refer to the Temperature Range
Table below for recommended operating conditions.
Do not store batteries along with metal objects due to risk of short circuit.
This cleaner uses Numatic Lithium-Ion batteries. Used batteries should be disposed of safely and placed in a sealed plastic bag and then handled according to all locally approved precautions and environmental regulations.
Do not crush.
Do not dismantle.
Do not heat or incinerate the batteries.
Do not short-circuit the batteries.
Do not immerse in any liquid.
Do not charge below 0°C.
Do not charge damaged batteries.
Use only original NUMATIC batteries, when replacement batteries are required.
If the batteries are leaking, return batteries to a disposal plant or a similar local facility.
The batteries must be removed from the appliance before the appliance is scrapped.
The battery is to be disposed of safely and in accordance with all locally approved precautions and environmental regulations.

Temperature Range Table

Charging	00C~400C
Discharging	00C~600C

Storage
Optimum| Below 200C
Limit| Below 550C

If the battery is found to be faulty at any time, contact Numatic International, or your supplier for information on disposal.

Lithium-Ion Battery Warranty

Warranty: Commercial Use

a. Batteries are warranted (1 Year) providing all battery care rules are followed
b. To claim warranty the following details must be supplied
i. Serial number of the machine
ii. Battery date code
iii. Date purchased
iv. Proof of Purchase
v. Maintenance history and charging regime Failure to use the correct Numatic charger will void your warranty.

Defective Batteries

ATTENTION

Please follow all safety guidelines set out.
A defective battery should not be stored inside buildings on any account.

If a customer wishes to return a battery to a supplier, then collection of the battery must be arranged by the supplier, however, Faulty batteries must not be returned through the postal system or by courier.
If on return to a supplier, OR at a customer base, a suspected defective battery shows any signs of impact damage, distortion, blistering, loose parts or leakage then on no account should it be off ered for condition checking. It must be considered defective and the procedures described from item 8 below should be followed.
If, on return to a supplier, OR at a customer base, a suspected defective battery, that shows No signs of impact damage, distortion, blistering, loose parts or leakage, may be off ered for condition checking with an appropriate battery condition checking device operated by a competent person.
If checking shows the battery to be defective then the procedures described from item 8 below should be followed.
If on checking the battery is found to be operational then a single recharge cycle under observation can be attempted with the appropriate Numatic charger.
If the battery recharges correctly on this single recharge cycle then it can be deemed a good battery.
If the battery fails to recharge correctly on this single recharge cycle then it must be deemed a defective battery and the procedures described from item 8 below should be followed.
On no account must any further attempt to recharge be made.
A defective battery should not be stored inside buildings on any account.
The defective battery should be discharged by placing it in a container of salt water located in a well – ventilated area. This container should contain 25 liters minimum of saline water at a concentration of 15gr common salt / liter of water. The container should have a closed locked lid but shouldn’t be sealed. The battery should be left fully immersed in the water to a depth of at least 100mm for at least 2 weeks. The water should be disposed of as hazardous waste when the discharge is complete.
The defective discharged battery can then be stored in a locked battery waste container which should be plastic or plastic lined and placed away from buildings and clearly signed as a defective battery container with appropriate warnings.
The batteries should then be sent for waste disposal according with your country’s waste regulations.

An example of a waste battery storage bin, keep well away from buildings.

ATTENTION

Please follow all safety guidelines set out.
Good batteries should be stored in a protected area away from sources of direct heat and sunlight and should be kept dry.
The temperature should not exceed 55 °C but preferably not be above 20 °C to maintain good battery performance.
Storage area should be of low humidity, non dusty and non corrosive atmosphere.

An example of a well protected area with a cage to protect against accidental impact damage and with the batteries stored in a protective container to protect from heat, impact and accidental spillage of liquids. Care when handling / moving with forklift trucks or pallet trucks is needed at all times to avoid any physical damage to the batteries.
If a good battery at any time is mishandled or subjected to any conditions that may damage it, as described in the battery Instruction manual supplied, it must then be considered as defective and procedures followed from Item 2 of this document overleaf

Important Warnings – Charger

Read all these warnings before using the charger.

CAUTION! Charge only Numatic Lithium-Ion batteries, other types of batteries may burst causing personal injury and damage.
Check the mains cord regularly for any sign of damage.
Do not use damaged devices.
If the mains cord of the charger is damaged, it must be replaced by an original NUMATIC INTERNATIONAL cord available from the manufacturer or service agent.
Protect the charger against moisture and store it in a dry place.
Do not use the charger if it is wet.
Do not charge below 0°C.
The mains voltage available must correspond to the voltage stated on the rating plate of the charger.
Do not operate charger in explosive environment.
Do not carry the charger by holding the mains cord.
Do not handle the electrical cord or plug, with wet hands.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Do not cover the charger.
Do not open the charger. Repairs shall be done only by authorised personnel.
Do not charge damaged batteries.
Do only charge dry batteries.
Do not charge non-rechargeable batteries in this charger.
The appliance is not intended for use by children or infirmed persons without supervision.

Warning: The battery included in this product must only be charged by the Numatic Charger and docking system supplied with the product and in NO circumstances should an alternative non Numatic charger be used as there is risk severe damage and fi re could result.

Instructions for Use – Charging Batteries

The charger is intended for use only on fl at surfaces, place horizontally on floor or work surface.
The charger is intended for use with the detachable power cord supplied, the power unit is capable of operating at diff erent voltages without user adjustment.
If the charger is damaged or does not charge anymore, please return to service centre.

Charging Procedure:

Ensure the battery is fully inserted into the charger.
Fit the mains power cord to charger and suitable power supply.
Please Note: If the battery is above its optimum charging temperature (due to ambient temperature or it if was recently discharged) the charger LED will illuminate on/off RED for a maximum of 40 minutes whilst the battery temperature falls to an acceptable level for charging to begin.
The LED should show RED to indicate charging.
Once fully charged the LED will show GREEN.
If power is supplied to the charger with no battery fi tted the LED will show GREEN to indicate STAND-BY status.

Hazards

Health Hazards (Acute & Chronic).
The chemicals used in the battery are in a sealed container.
Risk of exposure only occurs if the battery is abused or damaged.
Contact of electrolyte and lithium with skin and eyes should be avoided.
Signs & Symptoms of Exposure.
A damaged or leaking battery can cause chemical burns upon contact.

First Aid Measures

If exposed to any of the Chemicals mentioned in the Hazards section please follow the procedures below:

Eyes.
Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelid. Seek medical attention.

Skin.
Remove contaminated clothing and rinse skin with plenty of water or shower for 15 minutes. Seek medical attention.

Inhalation.
Vacate from site of exposure to fresh air immediately. Use oxygen if available.

Ingestion.
Give at least two glasses of milk or water. Induce vomiting unless patient is unconscious. Seek medical attention.

Note:
Inhalation, skin contact and eye contact are possible if the battery is damaged.
Exposure to internal contents, the corrosive fumes will be very irritating to skin, eyes and mucous membranes. Overexposure can cause symptoms of non-fi broid lung injury and membrane irritation.

Instructions for Use – Charging Batteries

The charger is intended for use only on fl at surfaces, place horizontally on fl oor or work suface.
The charger is intended for use with the detachable power cord supplied, the power unit is capable of operating at diff erent voltages without user adjustment. If the charger is damaged or does not charge anymore, please return to service centre.

Charging Procedure:

Ensure the battery is fully inserted into the charger.
Fit the mains power cord to charger and suitable power supply.
Please Note: If the battery is above its optimum charging temperature (due to ambient temperature or it if was recently discharged) the charger LED will illuminate on/off RED for a maximum of 40 minutes whilst the battery temperature falls to an acceptable level for charging to begin.
The LED should show RED to indicate charging.
Once fully charged the LED will show GREEN.
If power is supplied to the charger with no battery fitted the LED will show GREEN to indicate STAND-BY status.

Hazards

Health Hazards (Acute & Chronic). The chemicals used in the battery are in a sealed container. Risk of exposure only occurs if the battery is abused or damaged. Contact of electrolyte and lithium with skin and eyes should be avoided. Signs & Symptoms of Exposure. A damaged or leaking battery can cause chemical burns upon contact.

First Aid Measures

If exposed to any of the Chemicals mentioned in the Hazards section please follow the procedures below:

Eyes.
Flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower eyelid. Seek medical attention.
Skin.
Remove contaminated clothing and rinse skin with plenty of water or shower for 15 minutes. Seek medical attention.
Inhalation.
Vacate from site of exposure to fresh air immediately. Use oxygen if available.
Ingestion.
Give at least two glasses of milk or water. Induce vomiting unless patient is unconscious. Seek medical attention.
Note:
Inhalation, skin contact and eye contact are possible if the battery is damaged.
Exposure to internal contents, the corrosive fumes will be very irritating to skin, eyes and mucous membranes. Overexposure can cause symptoms of non-fi broid lung injury and membrane irritation

Good Batteries… Good Chargers… Good Care will ensure Good Results.

Replacement parts

Filter

Schematic diagram

Lithium-Ion Battery Warranty

Warranty: Commercial Use
a. Batteries are warranted (1 Year) providing all battery care rules are followed
b. To claim warranty the following details must be supplied
i. Serial number of the machine
ii. Battery date code
iii. Date purchased
iv. Proof of Purchase
v. Maintenance history and charging regime Failure to use the correct Numatic charger will void your warranty

Warranty

UKCA Declaration of Conformity

Manufacturer:| Numatic International Limited
Chard
Somerset
TA20 2GB
www.numatic.co.uk
Product:| NBV, PBT
Description:| Vacuum Cleaner – Commercial – Dry – Battery
We, Numatic hereby declare under our sole responsibility, that the above- mentioned product(s) is/are
in conformity with the following directives and standards.
S.I. 2008: 1597| Supply of Machinery Regulations| **EN60335-1:2012

AC:2014 + A11:2014 + A13:2017
EN60335-2-69:2012
EN62233:2008
---|---|---
S.I. 2016: 1091| EMC Regulations| EN55014-1:2017 + A11:2020
EN55014-2:1997 + A1:2001 + A2:2008
S.I. 2012: 3032| RoHS Regulations**|

Authorised Signatory: Mr. Matthew Coles Position: Head of Technology

Signed: Date: 1st Dec 20

Numatic International Limited,
Chard,
Somerset, TA20 2GB, UK

EU Declaration of Conformity

Manufacturer| Numatic International Limited Chard Somerset TA20 2GB
www.numatic.co.uk
Product| NBV, PBT
Description| Vacuum Cleaner – Commercial – Dry – Battery
We, Numatic hereby declare under our sole responsibility, that the abovementioned product(s) is/are in conformity with the following directives and standards.
2006/42/EC| Machinery Directive| EN60335-1:2012 + AC:2014 + A11:2014 + A13:2017
EN60335-2-69:2012
EN62233:2008
---|---|---
2014/30/EU| EMC Directive| EN55014-1:2017 + A11:2020
EN55014-2:1997 + A1:2001 + A2:2008
2011/65/EU| RoHS Directive|