WATERMARK 22-7.1.3-TICV Deck Mounted Kitchen Volume Control Spout Installation Guide

22-7.1.3-TICV Deck Mounted Kitchen Volume Control Spout

“`html

Product Information

Specifications

• Model: 22-7.1.3-TICV and 22-7.1.3A-TICV
• Applicable for: All 7.1.3 and 7.1.3A models
• Manufacturer: Watermark Designs
• Address: 350 Dewitt Ave. Brooklyn, NY 11207 USA
• Contact: T: 1 718 257 2800 | F: 1 718 257 2144 |
  customerservice@watermark-designs.com

Product Usage Instructions

1. Prepare the Mounting Surface

Can accommodate decks up to 2-1/2 inches thick.

Recommended hole size for handles: 1-3/8 inches.

Make 3 holes following the requirements shown on the
drawing.

Recommended hole size for spout: 1-3/8 inches.

2. Install the Spout

Tighten the lock nut to secure the spout in place.

3. Install the Handle and Valve

[A] Insert the handle assembly through a hole in the mounting
deck.

Thread the lock nut onto the bottom of the handle, beneath the
mounting surface.

[B] Align the handle so that the spout supply hose, which is
shorter and has a larger nut at the end, points towards the
user.

Tighten the lock nut against the bottom of the mounting surface
to secure the handle.

4. Install the Side Spray and Attach the Hoses (7.1.3A

Only)

FAQ

Q: What should I do if I encounter any issues during

installation?

A: Please contact our technical support team at the number
listed at the bottom of this page or email us at
technical@watermark-designs.com for assistance.

“`

Last Updated: 10/2023
Installation Instructions
for Deck Mounted Kitchen Volume Control Spout with Side Spray
The 22-7.1.3-TICV and 22-7.1.3A-TICV will be used as an example in this manual. Applicable for all 7.1.3 and 7.1.3A models. Page 1 of 5
Watermark Designs reserves the right to make revisions to product specifications without notice. All product dimensions are nominal.
350 Dewitt Ave. Brooklyn, NY 11207 USA | T: 1 718 257 2800 | F: 1 718 257 2144 | customerservice@watermark-designs.com

Last Updated: 10/2023
IMPORTANT INFORMATION
Thank you for choosing Watermark! We appreciate your commitment to Watermark quality products. Before you install the product, please fully review these installation instructions.
Before installation, unpack the product and inspect it for any damage. Make sure all the parts are present. If not installing immediately, place the product back into its protective packaging.
The appearance of the product may be different than what is shown in this installation manual, but the installation procedure will be the same.
Installation considerations: · Professional installation by a licensed plumber is strongly recommended. · Product should be installed according to local codes and regulations. · When installing:
· Use Teflon tape or pipe sealant for threaded connections. · DO NOT use plumber’s putty on any brass componants. This may cause the
finish to tarnish and void the warranty. Alkoxy silicone is recommended instead. · Flush the lines before and after installation (if applicable). · If the lines are sweated, do not overheat casting, which may damage
mechanisms. · Copper adaptors may be required to complete installation.
If you encounter any issues, please contact our technical support team at the number listed at the bottom of this page or email us at: technical@watermark- designs.com
Page 2 of 5
Watermark Designs reserves the right to make revisions to product specifications without notice. All product dimensions are nominal.
350 Dewitt Ave. Brooklyn, NY 11207 USA | T: 1 718 257 2800 | F: 1 718 257 2144 | customerservice@watermark-designs.com

PARTS BREAKDOWN

Last Updated: 10/2023

Spout

Handle Assembly

Side Spray

1x 1/2″ Female

Spout Nipple Assembly

2x 3/8″ Female

Side Spray Base

7.1.3A Models Only

You will need: – 1 x Wrench

Page 3 of 5
Watermark Designs reserves the right to make revisions to product specifications without notice. All product dimensions are nominal.
350 Dewitt Ave. Brooklyn, NY 11207 USA | T: 1 718 257 2800 | F: 1 718 257 2144 | customerservice@watermark-designs.com

1. Prepare the mounting surface

Last Updated: 10/2023

Can Accomodate Decks up to 2-1/2″ Thick

Recommended Hole Size for Handles: 1-3/8″

Make 3 holes following the requirements shown on the drawing.

Recommended Hole Size for Spout: 1-3/8″

2. Install the spout
ASSETS-FOR-7PG2
Position the spout over the hole. Thread Meets the applicable requirements of ASME A112.18.1-2005/CSA B125.1-05, entitled “Plumbing Supply Fittings” 7/17/2023 REV: n/a SCALE: 1:2 3th50eDleowcitkt AnveutBroonoktloyntNhYe 1n1i2p0p7 leI, tht:e7n18i-n25s7e-2r8t00 I f: 718-257-2144 I e: info@watermark- designs.com I www.watermark-designs.com the nipple into the bottom of the spout from beneath the mounting surface. Thread the nipple onto the spout and tighten. Then tighten the lock nut against the underside of the mounting surface to secure the spout.
Tighten Lock Nut
Page 4 of 5
Watermark Designs reserves the right to make revisions to product specifications without notice. All product dimensions are nominal.
350 Dewitt Ave. Brooklyn, NY 11207 USA | T: 1 718 257 2800 | F: 1 718 257 2144 | customerservice@watermark-designs.com

3. Install the handle and valve

Last Updated: 10/2023

[A] Insert the handle assembly

A

through a hole in the mounting deck.

Thread the lock nut onto the bottom

of the handle, beneath the mounting

surface.

[B] Align the handle. The spout supply hose, which is shorter and has a
larger nut at the end when compared to the two other flex hoses, should be pointing towards the user.

Tighten the lock nut against the bottom of the mounting surface to secure the handle.

Tighten Lock Nut
Spout Supply Hose Is Shorter and Has Larger Nut At the End

NOTE: Hose length shown is not to scale

B
Spout Supply Hose Should Face Foward