Panasonic ES-ST2N Household Rechargeable Shaver Instruction Manual

Operating Instructions
(Household) Rechargeable Shaver
Model No. ES‑ST2N

ES-ST2N Household Rechargeable Shaver

Thank you for purchasing this Panasonic product.
Before operating this unit, please read these instructions completely and save them for future use.

Safety precautions

To reduce the risk of injury, loss of life, electric shock, fire, and damage to property, always observe the following safety precautions.

Explanation of symbols

The following symbols are used to classify and describe the level of hazard, injury, and property damage caused when the denotation is disregarded and improper use is performed.

DANGER
Denotes a potential hazard that will result in serious injury or death.
WARNING
Denotes a potential hazard that could result in serious injury or death.
CAUTION
Denotes a hazard that could result in minor injury or property damage.
The following symbols are used to classify and describe the type of instructions to be observed.

This symbol is used to alert users to a specific operating procedure that must not be performed.
This symbol is used to alert users to a specific operating procedure that must be followed in order to operate the unit safely.

WARNING

► This product

This shaver has a built-in rechargeable battery. Do not throw into the fire, apply heat, or charge, use, or leave in a high-temperature environment.
– Doing so may cause overheating, ignition, or explosion.
Do not modify or repair.
– Doing so may cause fire, electric shock, or injury.
Contact an authorized service center for repair (battery change etc).
Never disassemble except when disposing of the product.
– Doing so may cause fire, electric shock, or injury.
►I n case of an abnormality or malfunction Immediately stop using and remove the adaptor if there is an abnormality or malfunction.

– Failure to do so may cause fire, electric shock, or injury.
< Abnormality or malfunction cases>

• The main unit, adaptor or cord is deformed or abnormally hot.
• The main unit, adaptor, or cord smells of burning.
• There is an abnormal sound during the use or charging of the main unit, adaptor, or cord.
  – Immediately request inspection or repair at an authorized service center.

►Power supply

Do not connect or disconnect the adaptor to a household outlet with a wet hand.
– Doing so may cause electric shock or injury.
Do not immerse the AC adaptor in water or wash it with water.
Do not place the AC adaptor over or near water filled sink or bathtub.
Never use the appliance if the AC adaptor is damaged or if the power plug fits loosely in a household outlet.
Do not damage, modify, or forcibly bend, pull, or twist the cord. Also, do not place anything heavy on or pinch the cord.
– Doing so may cause electric shock or fire due to a short circuit.

Do not use in a way exceeding the rating of the household outlet or the wiring.
– Exceeding the rating by connecting too many plugs to one household outlet may cause fire due to overheating.
Do not use anything other than the supplied AC adaptor for any purpose. Also, do not use any other product with the AC adaptor. (See page 8.)
– Doing so may cause burn or fire due to a short circuit.
Always ensure the appliance is operated on an electric power source matched to the rated voltage indicated on the AC adaptor.
Fully insert the adaptor.
– Failure to do so may cause fire or electric shock.
Disconnect the AC adaptor when cleaning the shaver with water.
– Failure to do so may cause electric shock or injury.

Regularly clean the power plug and the appliance plug to prevent dust from accumulating.
– Failure to do so may cause fire due to insulation failure caused by humidity.
►Preventing accidents
Do not place within reach of children or infants. Do not let them use it.
– Putting parts or accessories in the mouth may cause an accident or injury.
If oil is consumed accidentally, do not induce vomiting, drink a large amount of water and contact a physician.
If oil comes into contact with your eyes, wash immediately and thoroughly with running water and contact a physician.
– Failure to follow these instructions may result in physical problems.
►Take care of the following precautions as well This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
– Failure to do so may cause an accident or injury.
The supply cord cannot be replaced. If the cord is damaged, the AC adaptor should be scrapped.
– Failure to do so may cause an accident or injury.

CAUTION

►Protecting the skin
Do not use excessive pressure to apply the system’s outer foil to your lip or another part of your face.
Do not apply the system outer foil directly to blemishes or injured skin.
Do not touch the blade section (metallic section) of the inner blade.
– Doing so may cause injury to the skin or hand.
Do not forcefully press the system outer foil. Also, do not touch the system’s outer foil with fingers or nails when in use.
Do not use this product for hair on the head or any other part of the body.
– Doing so may cause injury to the skin or reduce the life of the system’s outer foil.
Check the system’s outer foil for cracks or deformations before use.
– Failure to do so may cause injury to the skin.
Be sure to place the carrying holder on the shaver when carrying around or storing.
– Failure to do so may cause injury to the skin or reduce the life of the system outer foil.
►Note the following precautions
Do not wrap the cord around the adaptor when storing.
– Doing so may cause the wire in the cord to break with the load, and may cause fire due to a short circuit.

Do not allow metal objects or trash to adhere to the power plug or the appliance plug.
– Doing so may cause electric shock or fire due to a short circuit.
Do not disconnect the adaptor or the appliance plug by holding onto the cord.
– Doing so may cause electric shock or injury.
Do not share your shaver with your family or other people.
– Doing so may result in infection or inflammation.
Do not drop or hit other objects.
– Doing so may cause injury.
Disconnect the adaptor from the household outlet when not charging.
– Failure to do so may cause electric shock or fire due to electrical leakage resulting from insulation deterioration.

Handling of the removed battery when disposing

DANGER

The rechargeable battery is exclusively for use with this appliance. Do not use the battery with other products. Do not charge the battery after it has been removed from the product.

• Do not throw into fire or apply heat.
• Do not hit, disassemble, modify, or puncture with a nail.
• Do not let the positive and negative terminals of the battery get in contact with each other through metallic objects.
• Do not keep the battery together with metallic jewelry such as hairpins.
• Do not use or leave the battery where it will be exposed to high temperatures, such as under direct sunlight or near other sources of heat.
• Never peel off the tube.

– Doing so may cause overheating, ignition, or explosion.

WARNING

After removing the rechargeable battery, do not keep it within reach of children and infants.
– The battery will harm the body if accidentally swallowed.
If this happens, consult a physician immediately.
If the battery fluid leaks out, do not touch the battery with your bare hands.
– The battery fluid may cause blindness if it comes in contact with your eyes.
Do not rub your eyes. Wash immediately with clean water and consult a physician.
– The battery fluid may cause inflammation or injury if it comes in contact with the skin or clothes.
Wash it off thoroughly with clean water and consult a physician.

Intended use

• This WET/DRY shaver can be used for wet shaving using shaving lather or for dry shaving. You can use this watertight shaver in the shower and clean it with water. The following symbol means suitable for use in a bath or shower.
  ► Notes

• Treat yourself to wet lather shaves for at least three weeks and notice the difference. Your Panasonic WET/DRY shaver requires a little time to get used to because your skin and beard need about a month to adjust to any new shaving method.

• Do not bring the system’s outer foil into contact with hard objects.
  Doing so may damage the blades as they are very thin and deform easily.

• Do not dry the main unit with a dryer or a fan heater.
  Doing so may cause malfunction or deformation of the parts.

• Do not leave the shaver exposed to direct sunlight with the foil frame detached.
  Doing so may deteriorate the waterproof rubber and degrade the waterproof function, which may cause malfunction.

• Store the shaver in a place with low humidity after use.
  Failure to do so may cause malfunction due to condensation or rust.

• Keep both the inner blades inserted. If only one of the inner blades is inserted, the shaver may be damaged.

• If you clean the shaver with water, do not use salt water or hot water. Do not soak the shaver in water for a long period of time.

• The following symbol indicates that a specific detachable power supply unit is required for connecting the electrical appliance to the supply mains. The type reference of the power supply unit is marked near the symbol.

Parts identification

The Main body

1. System outer foil

2.  Foil frame

3.  Foil frame release buttons

4. Cleaning shutter

5. Finger rest

6. Power switch
   To turn the shaver on and off and also lock and unlock the power switch.

7.  Switch lock lamp ( )

8. Charge status lamp ( )

9. Appliance socket

10. Inner blades

11. Trimmer

12. Trimmer handle

13. Outer foil section

14. System outer foil release buttons

15. Water inlet

16. AC adaptor (RE7-87)

17. Adaptor

18. Power plug

19. Cord

20. Appliance plug

Accessories
C Carrying holder
D Cleaning brush
E Oil

Before use

► Using the carrying holder
The shaver can be kept vertically. When transporting the shaver, you can use the carrying holder to protect the outer foil.

• When transporting the shaver, be sure to clean off any shavings before attaching the carrying holder.

► Attaching the carrying holder
Attach the carrying holder as illustrated.

• With the protrusion ( a) facing the front, securely attach the carrying holder to the shaver aligned to the orientation of the shaver head until it clicks.
  

► Removing the carrying holder
Remove the carrying holder while pressing down on both sides.

Charging the shaver

• Turn the shaver off.
• Attach the carrying holder so as not to scratch the system’s outer foil.
• Wipe off any water droplets on the appliance socket.

1. Insert the appliance plug into the shaver.

2. Plug in the adaptor into a household outlet.
   • Charging is completed after approx. 1 hour.
   The charging time may differ from the charging capacity.

3.  Disconnect the adaptor after charging is completed.
   • Charging the battery for more than 1 hour will not affect battery performance.

Note
You cannot operate the shaver while charging.While charging
The charge status lamp ( ) glows red.| After charging is completed

The charge status lamp ( ) turns off.

| Abnormal charging

The charge status lamp ( ) will blink twice every second.

---|---|---

• After charging is completed, turning the power switch ON with the shaver plugged in will cause the charge status lamp ( ) to light up and then turn off after 5 seconds.
  This shows that the shaver is fully charged.

• When charging the shaver for the first time or when it has not been in use for more than 6 months, the charging time may change or the charge status lamp ( ) may not glow for a few minutes. It will eventually glow if kept connected.

• Recommended ambient temperature for charging is 10 °C – 35 °C.
  It may take longer to charge or the battery may fail to charge properly in extremely high or low temperatures.
  The charge status lamp ( ) will blink twice every second when there is a problem with charging.
  Charge the shaver within the recommended ambient temperature range.

• The shaver can be used for approximately 2 weeks with a full charge. (Based on one 3‑minute dry‑shave use per day) The number of usable days varies depending on the following conditions.
  ‑ Beard thickness
  ‑ Pressure applied to the skin
  ‑ Ambient temperature
  ‑ Usage of wet shaving

• If there is noise from the radio or another source while using the shaver, move to a different location to use the shaver.

Using the shaver

1. Press and shave.

• The power cannot be turned on when the switch lock lamp ( ) blinks, as the power switch is locked.
  Press the power switch for more than 2 seconds to unlock. (See pages 11 and 12.)

Tips for better shaving
Apply the whole system’s outer foil perpendicularly against the skin and shave by slowly gliding the shaver over the face against the grain of the beard.

• The beard under the chin and around the throat can be shaved better by stretching the skin so the beard will stand.
• To prevent damaging the system outer foil, do not shave with only a part of the system outer foil.

You can also use a pen grip to hold the shaver.

2 Press when finished.

When the battery capacity is low
The charge status lamp ( ) blinks once every second when operating the shaver.

• You can shave 2 to 3 times after the charge status lamp ( ) blinks. (This will differ depending on usage.)

► Using the trimmer
Slide the trimmer handle up. Place at a right angle to your skin and move downwards to trim your sideburns. ► Tips for better usage
Apply the trimmer edge perpendicular to the skin gently and move downward slowly.

► Notes

• The “shaving sensor”, which automatically adjusts the power depending on the beard thickness, will operate.
  It will shave with high power on areas where the beard is heavy, and reduce the power on areas where the beard is thin, to reduce the burden on the skin.

• Before shaving, check that the cleaning shutter is closed.

• After wet shaving, wash the main body with water and apply oil to the system’s outer foil.

• Depending on the beard thickness or the amount of beard trimmings in the shaver head, the shaving sensor may not react and the driving sound may not change. This is not abnormal.

• The appliance may not operate at an ambient temperature lower than approximately 5 °C.

• The shaving sensor may not respond depending on the type and quantity of the shaving gel. This is not abnormal.

• To prevent erroneous operation, place your fingers on the finger rest while using the shaver.

Operation and display of the switch lock

►Locking the power switch 1. Press once and then release.
• The shaver starts operating.| 2. Press for more than 2 seconds.
• The switch lock lamp ( ) will light up for 5 seconds and turn off.
• The shaver will stop operating.| 3. Release .
---|---|---
| |

►Unlocking the power switch 1. Press for more than 2 seconds.
• The switch lock lamp ( ) will turn off.| 2. Once the shaver starts operating, release
---|---
|

• The power switch cannot be unlocked while charging.
• The power switch is locked when the switch lock lamp ( ) blinks for 5 seconds and the shaver does not operate even though the power switch is pressed.

Cleaning the shaver

We recommend cleaning the shaver after each use.

1. Turn the shaver off and disconnect the AC adaptor.

2. Apply some hand soap and some water to the system’s outer foil.
   • Close the cleaning shutter.

3. Turn the shaver on.

There are two ways to clean the shaver, depending on the actual dirt level.

4. Slide the cleaning shutter until it clicks. 5. Clean the outer foil section with running water. 6. Turn the shaver off.
• Rinse with water and shake up and down several times to remove the water.| 4. Turn the shaver off after 10 – 20 seconds.
5. Remove the outer foil section and turn the shaver on.
6. Clean the shaver and the outer foil section with running water.
• Rinse with water and shake up and down several times to remove the water.

7. Wipe off any drops of water with a dry cloth.
8. Dry the outer foil section, the shaver, and the trimmer completely.
• Allow the shaver to dry in the shade, avoid direct sunlight and then apply oil.9. Lubricate the shaver.
It will keep the movement of the blade smooth and maintain a comfortable shave.
1. Apply one drop of oil to each of the system’s outer foils.
2. Raise the trimmer and apply a drop of oil.
3. Switch the shaver on, and run it for approximately five seconds.
4. Switch off the shaver, and wipe off any excess oil from the system outer foil with a soft cloth.

► Notes

• Do not use any kitchen or bathroom detergents other than hand soap.
  Doing so may cause malfunction.

• Do not wipe with thinners, benzine, alcohol, etc.
  Doing so may cause malfunction or cracking or discoloration of the parts.
  Wipe with diluted soapy water.

• Be careful not to hit the main body on the sink or any other object while draining the water. Failure to do so may cause malfunction.

Cleaning with the brush

Remove the outer foil section and the inner blades. (See this page.)
► Cleaning with the long brush
Clean the outer foil section, system outer foil, the shaver body, and the trimmer using the long brush.
► Cleaning with the short brush

• Clean the inner blades using the short brush by moving them in the direction as illustrated.
• Do not move the short brush perpendicularly against the blades as it will damage the inner blades and affect their sharpness.

Replacing the system’s outer foil and the inner blades system outer foil| once every year
---|---
inner blades| once every two years

► Removing the outer foil section
Press the foil frame release buttons and lift the outer foil section upwards.
► Attaching the outer foil section
After turning the water inlet surface to the front, securely attach the outer foil section to the shaver until it clicks.

► Replacing the system’s outer foil

1. Press the system outer foil release buttons and pull down the system outer foil.
2. Align the water inlet surface and the system outer foil mark ( ) and securely attach them together. • Do not press the system outer foil release buttons with excessive force.
   Doing so may bend the system’s outer foil, preventing complete attachment to the foil frame.

► Replacing the inner blades

1. Remove the inner blades one at a time.
2. Insert the inner blades one at a time.

► Note
Do not throw away the foil frame.
►Replacement parts
Replacement parts are available at your dealer or Service Center.

Replacement parts for
ES-ST2N| System outer foil| WES9087
---|---|---
Inner blades| WES9068

FAQ

Will the battery deteriorate if not used for an extended period of time?

– The battery will deteriorate if not used for over 6 months, so make sure to perform a full charge at least once every 6 months.

Can I charge the shaver after every use?

– The battery used is a lithium‑ion, so charging after every use will have no effect on battery life.

Why should the adaptor be disconnected after use?

– Charging the battery for more than 1 hour will not affect battery performance, but disconnect the adaptor for safety and to save energy.

What is the constituent of the dedicated oil?

– The constituent of the oil is liquid paraffin.

Troubleshooting

Perform the following actions.
If the problems still cannot be solved, contact the store where you purchased the unit or a service center authorized by Panasonic for repair.

The power switch does
not turn ON.| Unlock the switch lock.
(See page 12.)
The shaving sensor does
not respond.| Depending on the beard thickness or the amount of beard trimmings
in the shaver head, the shaving sensor may not react and the driving sound may not change.
This is not abnormal.
The shaving sensor may not respond depending on the type
and quantity of the shaving gel.
This is not abnormal.
The shaving sensor may not respond when the remaining battery capacity is low. If this happens, recharge the shaver.
Apply oil.
(See page 13.)
The shaving sensor may not respond when there is not enough oil on the blades.
The shaving sensor
responds even though the
shaver is not in contact
with the skin.| Clean the beard trimmings from the shaver.
When the shaver is extremely dirty, remove the foil frame and wash it with water. (See page 12.)
Replace the system’s outer foil and/ or inner blades.
The expected life of system’s outer foil and inner blades:
System outer foil: Approximately 1 year
Inner blades: Approximately 2 years
---|---
The shaver cannot be
charged.| The recommended temperature for charging is 10 °C – 35 °C. If
charged at a temperature other than the recommended temperature, the shaver may take longer to charge or may not charge at all.
Operating time is short
even after a full charge.| Although the shaver can be used for about 2 weeks after a full charge (assuming dry‑shave use for 3 minutes per day), the usable number of days might be lower depending on how or where the shaver is used (for example, when used for wet shaving).
Apply oil.
When the number of operations per charge starts to decrease, the
the battery is nearing the end of its life.
Shaver does not operate
even after charging.| Use the appliance at an ambient temperature of approximately 5 °C or higher.
The battery has reached the end of its life.
The shaver will not operate with the AC adaptor connected. Please use the shaver after it has been sufficiently charged and the AC adaptor disconnected.
---|---
The driving sound
changes while shaving.| The shaving sensor is operating.
The sound changes depending on the beard thickness.
Makes a loud sound.| Apply oil.
The blades will not move smoothly when there is no oil on the blades, requiring more power.
The shaver makes a high‑pitched sound due to the linear motor drive.
This does not indicate a problem.
Confirm that the blades are properly attached.
Clean the system’s outer foil with the brush.
This can be improved by cleaning every time after shaving.
The shaver cannot be
properly cleaned even
after water is poured from
the water inlet.| When the shaver is very dirty, first use the cleaning brush to remove
beard trimmings.
Or, remove the foil frame and wash it with water. (See page 12.)
Shavings fly out in all
directions.| This can be improved by cleaning every time after shaving.
Clean the inner blades with the brush when shavings are adhering to the inner blades.
Confirm that the cleaning shutter is firmly closed.
The system’s outer foil gets hot.| Apply oil.
Replace the system’s outer foil if it is damaged or deformed.
(See page 14.)
You do not get as close a
shave as before.| Replace the system’s outer foil and/ or inner blades.
The expected life of the system’s outer foil and inner blades:
System outer foil:
Approximately 1-year Inner blades:
Approximately 2 years

Battery life

The life of the battery is 3 years. The battery in this shaver is not intended to be replaced by consumers. Has the battery been replaced by an authorized service center?

Removing the built-in rechargeable battery

Remove the built-in rechargeable battery before disposing of the shaver.
Please make sure that the battery is disposed of at an officially designated location if there is one.
This figure must only be used when disposing of the shaver, and must not be used to repair it. If you dismantle the shaver yourself, it will no longer be waterproof, which may cause it to malfunction.

• Remove the shaver from the AC adaptor.
• Press the power switch to turn on the power and then keep the power on until the battery is completely discharged.
• Perform steps 1 to 6 and lift the battery, and then remove it.
• Take care not to short-circuit the positive and negative terminals of the removed battery, and insulate the terminals by applying tape to them.

For environmental protection and recycling of materials, This shaver contains a Lithium‑ion battery.
Please make sure that the battery is disposed of at an officially assigned location if there is one in your country.

Specifications

Power source| See the nameplate on the AC adaptor. (Automatic voltage conversion)
---|---
Motor voltage| 3.6 V ****
Charging time| Approx. 1 hour

This product is intended for household use only.

Panasonic Corporation
http://www.panasonic.com
© Panasonic Corporation 2016
Printed in Japan
ES9700ST2N1J Y0916‑0

References

• Panasonic Australia | Air Con | Cameras | Home Appliances

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>