LaView LV-X2-W-EU HD Image Large Projection Area LED Lights User Manual

LaView LV-X2-W-EU HD Image Large Projection Area LED Lights

What’s In the Box

Laser Warning

LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT
Diode Laser- Max. Output < 1 mW Wavelength 510-525nm
Classified per IEC 60825-1 Ed. 3.0:2014

• Use of controls or adjustments or performance of procedures other than those specie herein may result in hazardous radiation exposure.
• This product is classed as a Class 2 laser product and complies with the applicable parts of IEC/EN 60825-1 Ed. 2.02007 and Ed. 3.02014.
• Do not stare into the beams emitted from the product. Intentional long term viewing of CLASS 2 levels of laser light can be hazardous.
• This product uses diffractive optics to scatter the beam energy This scattering effect causes the energy concentration to drop below the exposure limits for momentary or accidental viewing at a relatively short distance from the laser aperture.
• As with all bright light-sources, when you operate this device in unsupervised general public areas, it is recommended that up-close access to the light be restricted or prevented and the beams be directed into locations where persons are not expected.
• This laser display device incorporates a CLASS 38 laser system which, by itself, may be hazardous.
• However, this laser display product incorporates a protective housing and diffractive optics in its design so that there is no exposure or human access to laser radiation during operation or maintenance above the CLASS 2 limits.
• Each individual laser beamlet’s power is below the Class 2 limit of 1 mW.
• UNDER NO CIRCUMSTANCES shall attempts be made to open the protective housing or operate the device if the aperture window is damaged.
• All service to this laser display device requiring the protective housing to be opened and/ or removed shall be performed by service personnel or their authorized agents. Opening the protective housing voids the warranty.

NO LASERS SHOULD BE POINTED INTO THE SKY WITHIN 10 NAUTICAL MILES (18.5 km) OF AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS SPECIFIC PERIMETER, WE RECOMMEND THE LASERS BE POINTED DOWN AT THE GROUND SO NO STRAY BEAMS ARE PROJECTED INTO THE AIR. CHECKWITH YOUR LOCAL AIRPORT OR PROVINCIAL GUIDELINES FOR FURTHER INFORMATION.

Important Safety Notice

• Before using the projector, check if all components, including the projector, USB cable, USB adapter is intact.
• If any component is broken, contact our customer service team for repair or replacement before operating the product.
• This Is not a toy.
• Young children and toddler MUST be supervised while using this device at all times.
• ONLY USE manufacture- provided USB adapter. Use third-party USB adapter may permanently damage the projector ONLY clean the surface or lens with a soft dry cloth.
• ONLY use the projector within rated operating temperature.
• ONLY place the project on a flat and horizontal surface.
• NEVER place the project close to fire, water or ay dangerous environment NEVER Stare at the LED or laser when they are turned on.
• This unit is not waterproof.
• Please use and store this product indoors.
• T you plan not to use the projector tor a long time, unplug its power and store it to a dry place.
• Before changing a disc, always power off the projector to avoid sudden brightness change.
• If the device is short-circuited or smoking, please unplug the power cord, stop using it and contact us immediately.

Specifications

Before start operating the X1 projector, please read Important Safety Notice section of this user manual.
This projector is designed to ONLY be used in a dark room with low light environment.

For best projection result, please ensure the projector is placed at a location that meets the following minimum requirement:

• A dark room (with no light pollution such as TV or table lamp)
• Projector facing towards a ceiling /wall that has at lease 9 fix 9 ftflat surface
• Projector being placed 5 ft- 8 ft from the ceiling/ wall

Step 1: Install the disc onto the disc tray.

Step 2: Insert the disc tray to the projector with the front side facing towards lens.

Step 3: Connect Odyssey X1 to USB cable and USB adapter

Step4: Press the power button. The LED projection and laser stars will gradually illuminate

Steps5: Rotate the focus dial to adjust the projection clarity until you get a cedar image.

How to Adjust Focus Dial?

YOU MUST ADJUST FOCUS DIAL in order to get a clear image of the projection. Rotate the focus dial clockwise or counter-clockwise until the center of the projection image is clear and focused. For best clarity, you may need to try back and forth and rotate delicately when image is starting to get clear. If you are setting up the projector for the first time, turn the focus dial clockwise all the way to the end, and then turn counter-clockwise gradually until you get a clear focus Due to the optical structure of the projector, the surrounding area may not be as clear as the center area for some discs, especially when the lens is placed at an angle, or the projection is not on a flat surface. This is normal due to principle of optical imaging. This is not a product defect.

FOR BEST PROJECTION RESULT

• The darker the display area, the brighter the projection image will appear
• Ensure the projector is facing towards as close to the center of the wall/ceilling as possible
• Ensure the lens is facing perpendicularly to the wall/ceiling
• Ensure the center area is focused before the surrounding area

How to Install or Change a Disc?

• The disc MUST be fixated to the disc tray before use.

• Turn off the projector before removing the disc tray to avoid Sudden brightness change that may hurt your eyes.

• To remove an existing disc, hold the gear wheel with one finger. Use two fingers of your other hand to hold the disc and turn it clockwise.
  

• To install a disc, align and press the disc to the disc tray.

• Then turn the disc counter-clockwise to fixate the disc.

• Hold the gear wheel on the disc tray with a finger when you turn the disc.
  

How to Adjust Projection Angle

Hold the top part of the projector and pul up the lens to adjust the projection angle. Avoid touching the lens.

You can adjust angle to 0-90° Spin the projector back and forth to find a ceiling/wall position that has largest flat surface area.

Rotate the lens all the way up, to point the projection to the ceiling.

Other Functions

Child lock

• Press and hold the laser button on the projector for 10 sec and laser will blink for 2 sec, which means the child lock is on,
• When child lock is turned on, laser is disabled and cannot be turned on by either the laser button on the projector or remote control.
• To turn off child lock, press and hold the laser button for 10 sec again.

Timer
Press the timer button on the projector once to switch timer among 15 min, 30 min and 60 min. If no timer is set, the projector will turn off automatically after 3 hours of operation Alliteratively, you can use the timer buttons on the remote control to set a timer

Adjust rotation speed
Press the rotation button on the projector acne to switch rotation speed between slow, medium, fast level Alternatively, you can use the rotation speed button on the remote control to increase or decrease rotation speed.

Adjust laser brightness
Press the laser button on the projector once to switch laser brightness between low, medium, high level Alternatively., you can Use the brightness setting buttons on the remote control to increase or decrees laser brightness.

Blinking laser stars
Press the laser button on the projector 4 times to turn on blinking laser effect. Alternatively, you can use the blinking laser button on the remote control to turn on blinking laser effect.

FAQ

Why is the projection image is so vague?
Ensure the disc is fixated (locked) onto the disc tray Ensure the disc is installed correctly to the disc tray with correct side facing up Rotate the focus dial back and forth to adjust the focus. Read the ‘How to adjust focus dial’ section of this manual for more details The focus of each disc may slightly differ. You may need to adjust focus slightly when you change to a new disc Ensure the plastic film covering the lens is removed

Why I cannot see any projection image?
Ensure the projector is placed in a dark room and all lights are turned off Ensure the projector is correctly powered Check if the USB adapter or USB cable is broken Press the power button once firmly Ensure the lens is not covered by any object

Can I power the projector with a power bank?
You may use a power bank that has DC 5V 1A USB-A output to power the projector for a short time use

Can I use it in the living room?
Yes. You may use the projector in any indoor rooms. However, for best projection result,.please ensure the room is as dark as possible. Some discs may work when some ambient light is on, such as TV or a night light. But generally, the darker this display area, the brighter the projection image will appear

Why does laser look so bright on some discs?
While X1 is designed to fit comprehensive night light environment, some discs focus on the reality or clarity of space and universe. In such case, some black and white discs such as ‘Earth and Moon and ‘Southern Hemisphere’ do not fit laser’s brightness. You can try different discs that works better with laser. You can always adjust the laser brightness with remote control for best result

What should I do if the projector is broken?
This product carries a limited warranty against defects in workmanship and material. La View agrees to replace the defective product free of charge within the stated warranty period. Please contact our customer service team immediately if the product becomes defective

Where can I buy more discs?
You can purchase more discs on laviewusa.com, Amazon.com or shop via Lavu App. When you download and shop via La View App, use coupon code ODESSEY to get 10% off on any disc purchases

Button Functions

Need Help?

LIVE CHAT:
Download La View App from App Store

Email: info@laviewusa.com Our professional techinicians are commited to reply all your requests within 24 hours

If you purchased from Amazon, you can also contact our professional customer service team in your Amazon account

Product Warranty

Our LabVIEW prowl is protected by Aiyar warranty from tenure case date. Far more intormiatton on repairs, exchanged, and Outer pouches, please visit www.aviewUSA.com Please send all inquiries through the Lon tact Form on our website, or email Us at info@laviewusa.com. And our technicians would be glad to assist you

Disc Gallery

To purchase more discs, search Laview Odyssey Disc on Amazon.com to buy more genuine Odyssey X1 discs You can also download Laview App from App Store and shop with coupon code ODYSSEY at checkout to get 10% off any disc purchases

Home Security Simplified www.laviewusa.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>