owon SPF-1010-WB-TY Smart Pet Feeder User Guide

owon SPF-1010-WB-TY Smart Pet Feeder Preface

A quick start by the following steps:

1. Please scan the QR code on the packaging box or search ‘Smartlife’ from the APP store to download the APP.
2. Make sure the device’s Wi-Fi indicator is rapidly blinking. If not, please reset it by holding the OK button for 5 seconds until the power indicator flashes.
3. Keep close to the feeder, then open your Bluetooth and App. The device will be automatically detected and shown in the App.
4. Select ‘Go to add’ to add automatically the Pet Feeder in the “Small Home Appliances” list.
   For more details about network pairing, please refer to chapter 5.

Safety Notice

WARNING: Failure to follow these safety notices could result in fire, electric shock, other injuries, or damage to the Smart Pet Feeder and other property. Read all the safety notices below before using the Smart Pet Feeder.

• Avoid high humidity or extreme temperatures.
• Avoid long exposure to direct sunlight or strong ultraviolet light.
• Do not drop or expose the unit to intense vibration.
• Do not disassemble or try to repair the unit yourself.
• Do not expose the unit or its accessories to flammable liquids, gases or other explosives.

Technical Specifications

Welcome

The Smart Pet Feeder allows you to feed your pet remotely or apply schedules for automatic feeding. You can get the feeding information anywhere at any time.
This guide will provide you with an overview of the product and help you get through the initial setup.

Features:

• Wi-Fi Remote control -Tuya APP smartphone programmable.
• Automatic & manual feeding
• Accurate feeding -Schedule up to 10 feeds per day
• 4L food capacity -4L large capacity
• Dual power protective -Battery backup, continuous operation during power or internet failure

In the box

• Pet Feeder x 1
• Power Adapter x 1
• Quick Guide x 1
• Please check the condition and the accessories of pet feeder after you open the box.

APP Download:

1. Remove the cover and scan the QR Code with your smartphone.
2. Search ‘Smartlife’ APP from App store.

Tips:
Dry and solid pet food only, recommed food diameter between 5 to 10mm.

Get to know your device

• Battery box
  3 x D-size batteries. Please pay attention to the polarity. Please note that the battery charging is for backup purpose only. If you wish to control the pet feeder remotely, power supply is needed.

• Power switch
  — for ON, ○ for OFF.

• Power jack
  Use the supplied power adapter.

OK Button:

• Tap once to feed once in 1 portion
• Reset the network configuration
  Hold the ‘OK’ button for 5 seconds until the power indicator flashes once to reset. The device will enter the EZ pair mode at the first reset. If resetting the device again in the EZ pair mode, it will change to AP pair mode.

Wi-Fi indicator
The Wi-Fi status gives the following information:

• EZ pair mode (Default): Quick pair devices. You can set all devices to this mode, and then add devices in batches on your phone.
• AP pair mode: If you would like to pair one specific device during many devices. Please refer to FAQ1 to configure network in this mode.

Get started

To get started, you will need:

1. Connect your phone to the 2.4Ghz Wi-Fi network.
2. A mobile phone with a mobile APP installed.

Then follow the steps below:

1. Power on the Smart Pet Feeder.
2. Make sure the Wi-Fi indicator is rapidly blinking. If not, please reset it.

Add devices

1. Open your App.
2. Login with an existing account. If you are a new user, you need to create an account at first.
3. Turn on “Bluetooth” and “Location” on your phone before connecting the Wi-Fi.
4. Once login, the phone will automatically detect the device via Bluetooth. And choose “Go to add”.
5. Enter your home Wi-Fi account and password (Only support 2.4Ghz Wi-Fi), then tap “Next” button.

Other device adding methods

Configure the network in EZ mode.
Note: In this case, no need to turn on your phone’s bluetooth.

• Please click the ‘+’ button at the top right corner of the App to add devices.
• Select ‘Pet Feeder’ to add manually the Pet Feeder in “Small Home Appliances” list.
• Enter your home Wi-Fi account and password (Only support 2.4Ghz Wi-Fi), then tap “Next” button.
• Place the router, mobile phone, and Pet Feeder as close as possible. Confirm the indicator on your device is rapidly blink, then tap “Next” to wait for connection.

Configure the network in AP mode.

• Reset the device in EZ pair mode, it will switch to AP pair mode. The indicator on your device will blink slowly.
• Room management
• The switch the network configuration mode to AP mode at the upper right corner of the APP when you add the device.
• Place the router, mobile phone and Pet Feeder as close as possible. Confirm the indicator on your device is slowly blink, then tap “Next” to wait for connection.
• After the device has been added, you can to rename the  use device.

app Overview:

Home

1. Device list
   You can check the added device, tap one to enter control board

2. Location information
   Information about your local weather conditions, outdoor temperature, PM

3. home management
   Add or delete home and manage home names, rooms, locations, and members

4. Room management
   Manage room. You can create rooms and assign devices to each room

5. Voice control (Temporarily not available on App)
   Smart: Create a smart scene and add an automatic function(Temporarily not available)
   Me: App settings and FAQ about the app

Control board:

Select the target Pet Feeder in device list then enter the control board Meal plan
Tap to edit the schedule for the automatic feed. Schedule supports up to 10 items. The error of the schedule is about 30 seconds.
Feed record
Tap to check the feeding history.
Feed
Tap to feed manually. The maximum number of portion is 12 at a time.
Feeder status display
It will have three different status: Standby, Feeding and Done.
Total portion
Tap “-” to reduce feeding portion and tap “+” to add feeding portion when manual feeding. The maximum number of portion is 12 at a time.
More settings
Tap for more settings, like rename device, device information, third-party control and others.
Device setting
After confirming to restore factory settings, the feeding record and device name of the device will be cleared. At the same time, the device will be deleted from the account and restore to the state of EZ pair mode.

Food stuck alarm

When the pet food get stucked, the APP will receive the alarm. And the red light will flash slowly.

Feeding plan display:
The next feeding time and the number of portions will be shown.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>