MAYTAG W11402365A Fingerprint Resistant Stainless Steel French Door Refrigerator User Guide
- June 9, 2024
- Maytag
Table of Contents
MAYTAG W11402365A Fingerprint Resistant Stainless Steel French Door
Refrigerator 
OPERATING INSTRUCTIONS
IMPORTANT: Before operating this appliance, make sure it has been
properly installed according to the appliance’s Owner’s Manual.
The controls are located above the external dispenser. Touch any control
button on the dispenser panel to activate the display screen.
NOTE: The display screen on the dispenser control panel will turn off
automatically and enter “sleep” mode when the control buttons and dispenser
levers have not been used for 2 minutes or more. While in “sleep” mode, the
first press of a control button will only reactivate the display screen,
without changing any settings. After reactivation, changes to any settings can
then be made. If no changes are made within 2 minutes, the display will re-
enter “sleep” mode.
For your convenience, your refrigerator and freezer temperature controls are set to the recommended set points at the factory. When you first install your refrigerator, make sure the temperature controls are still set to the recommended set points. The recommended set points are 37°F (3°C) for the refrigerator and 0°F (-18°C) for the freezer.
IMPORTANT:
-
Wait 24 hours for your refrigerator to cool completely before adding food. If you add food before the refrigerator has cooled completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer controls to a colder-than- recommended setting will not cool the compartments any faster. -
If the temperature is too warm or too cold in the refrigerator or freezer, first check the air vents to be sure they are not blocked before adjusting the controls.
-
The recommended settings should be correct for normal household refrigerator use. The controls are set correctly when milk or juice is as cold as you like and when ice cream is firm.
NOTE: Areas such as a garage, basement, or porch may have higher humidity or extreme temperatures. You may need to adjust the temperature away from the recommended settings to accommodate for these conditions. -
Wait at least 24 hours between adjustments. Recheck the temperatures before other adjustments are made.
TEMPERATURE SET POINTS
-
To view and adjust the set points, press and hold Temp for 3 seconds to activate temperature mode.
NOTE: To view Celsius temperatures, press the Light button, when adjust mode is activated. To return the display setting to Fahrenheit, press the Light button again.
Recommended Refrigerator Temperature
Fridge set point range: 33°F to 45°F (0°C to 7°C)
Recommended Freezer Temperature
Freezer set point range: -5°F to 5°F (-21°C to -15°C) -
When Adjust mode is activated, the display screen shows the refrigerator set point and “Fridge” appears.
-
Press Lock to raise the set point, or press PowerCold™ to lower the set point.
-
When you have finished viewing (and adjusting if desired) the refrigerator set point, press Temp to change the display to show the freezer set point. When the zone has been changed, “Freezer” appears on the display screen.
-
Press Lock to raise the set point, or press PowerCold™ to lower the set point.
When adjusting temperature set points, use the following chart as a guide.
| CONDITION: | TEMPERATURE ADJUSTMENT: |
|---|---|
| Refrigerator too cold | Refrigerator setting 1° higher |
| Refrigerator too warm | Refrigerator setting 1° lower |
| Freezer too cold | Freezer setting 1° higher |
| Freezer too warm / too little ice | Freezer setting 1° lower |
Save/Confirm Temperature Settings
When you have finished viewing (and adjusting if desired) both the
refrigerator and freezer set points, press Filter to save the settings.
NOTE: To exit without saving changes, press Ice Type at any time while in
adjust mode, or allow about 60 seconds of inactivity and adjust mode will turn
off automatically.
COOLING ON/OFF
Your refrigerator and freezer will not cool when the cooling is turned off.
To turn the cooling off, press and hold the Lock and Filter buttons at the
same time for 3 seconds. When cooling is off, “Cooling Off” will appear on the
display screen.
IMPORTANT:
- To avoid unintentionally locking the dispenser or changing other settings, press both buttons at exactly the same time.
- Press and hold Lock and Filter for 3 seconds again to turn cooling back on.
ICE MAKER ON/OFF
- You can turn the ice maker on or off from the control panel.
- To manually turn off the ice maker, press Temp and PowerCold® at the same time and hold for 3 seconds until the “Ice Maker Off” icon lights up. When the ice maker is set to off, it will stop producing ice.
- Pressing and holding Temp and PowerCold® again for 3 seconds turns on the ice maker and the “Ice Maker Off” icon disappears.
PowerCold®® FEATURE
The PowerCold® feature assists with periods of high refrigerator use, full grocery loads, or temporarily warm room temperatures. Once selected, Fast Cool will remain on for 24 hours unless manually turned off.
- Press PowerCold® to set the freezer and refrigerator to the lowest temperature setting. When the feature is on, the PowerCold® icon will appear on the dispenser display screen.
- To manually turn off the PowerCold® feature, press PowerCold again or adjust the refrigerator temperature set point. The PowerCold® icon will disappear when the feature is off.
NOTE: Setting the freezer to a colder temperature may make some foods, such as ice cream, harder.
WATER FILTER STATUS
When a water filter has been installed in the refrigerator, the water filter status lights help you know when to change your water filter. See “Water Filtration System” in the Owner’s Manual.
The disposable water filter should be replaced at least every 6 months. If the water flow to the water dispenser or ice maker decreases noticeably before 6 months have passed, replace the water filter more often.
- The water filter status icon changes will change from Normal (blue water) to Order (red waves) and “Order Filter” (orange) when 90% of the volume of water for which the filter is rated has passed through the filter or 5 months have passed since the filter was installed.
- The “Replace Filter” (red) icon will illuminate and blink continuously during dispensing when the rated volume of water has passed through the filter or 6 months have passed since the filter was installed. A new water filter should be installed immediately when the Replace light is illuminated.
- After 14 days at Replace Filter stage, the “Replace Filter” and “Water” icons will glow (red) at all times and blink continuously during dispensing. Also, an alert chime will sound three times following dispensing.
- After changing the water filter, reset the water filter status. On the display screen, press and hold Filter Reset for 3 seconds. The status light will change from Replace Filter (red) to Normal (blue water) when the system is reset.
DISPENSER LIGHT
When you use the dispenser, the lights will turn on automatically. If you want the light to be on continuously, you may choose either On or Dim. The display screen indicates which mode is selected.
- ON: Press Light to turn on the dispenser light.
- DIM: Press Light a second time to select Dim mode. The dispenser light will remain on, but at a lower intensity.
- OFF: Press Light a third time to turn off the dispenser light.
The dispenser lights are LEDs that cannot be changed. If it appears that your dispenser lights are not working, see online “Troubleshooting” for more information.
DISPENSER LOCK
The dispenser can be turned off for easy cleaning or to avoid unintentional dispensing by small children and pets.
NOTE: The lock feature does not shut off power to the refrigerator, to the ice maker, or to the dispenser light. It simply deactivates the controls and dispenser lever. To turn off the ice maker, see the “Ice Maker and Storage Bin” section in the Owner’s Manual.
- Press and hold Lock for 3 seconds to lock the dispenser.
- Press and hold Lock a second time to unlock the dispenser. The display screen indicates when the dispenser is locked.
Online Ordering Information
For detailed installation instructions and maintenance information, winter
storage, and transportation tips, please see the Owner’s Manual included with
your appliance.
For information on any of the following items, the full cycle guide, detailed
product dimensions, or for complete instructions for use and installation,
please visit https://www.maytag.com/owners, or in Canada
https://www.maytag.ca/owners. This may save you the cost of a service call.
However, if you need to contact us, use the information listed below for the
appropriate region.
United States:
1–800–344–1274
Maytag Brand Appliances Customer eXperience Center 553 Benson Road
Benton Harbor, MI 49022–2692
Canada:
1–800–688–2002
Maytag Brand Appliances Customer eXperience Centre 200–6750 Century Ave.
Mississauga, Ontario L5N 0B7
SAVE THESE INSTRUCTIONS
Documents / Resources
|
MAYTAG W11402365A Fingerprint Resistant Stainless Steel French Door
Refrigerator
[pdf] User Guide
W11402365A Fingerprint Resistant Stainless Steel French Door Refrigerator,
W11402365A, Fingerprint Resistant Stainless Steel French Door Refrigerator,
Resistant Stainless Steel French Door Refrigerator, Steel French Door
Refrigerator, French Door Refrigerator, Door Refrigerator, Refrigerator
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>