Boltune BT-BH034 True Wireless Stereo Earbuds User Guide
- June 9, 2024
- Boltune
Table of Contents
Boltune BT-BH034 True Wireless Stereo Earbuds
Reminder Card
- Before use, please remove the insulation piece above the Earphone
- The pictures in this manual are schematic diagrams, which may deviate from the actual object, please refer to the product.
Using Your Earbuds
Charge Earbuds
- When the indicator on the earbud flashes white, or the voice prompt “Battery low, please charge” is heard, put the earbuds
into the charging case to charge.
Charge Charging Case
- Insert the charging cable into the charging case and connect it to any USB ports.
- Charging, Solid on; Fully Charged, Off
- Input: 5V 200mA(Earbuds)
- 5V lA(Charging Case)
Warning
- The rechargeable battery of this product must be disposed of properly for recycling. Please do not put the battery in the fire to avoid an explosion.
- Use a power source that has been approved by the relevant authorities meets the electrical specifications of the equipment, and meets local regulatory requirements (e.g., UL, CSA, VDE, CQC), otherwise, fire, explosion, and other hazards may OCcur.
- Take out the earbuds
- Put the earbuds into the case
- Bluetooth
- For the first time, take out the earbuds and they will enter pairing mode automatically.
- The earbuds can be connected to the last paired device when they have been turned on again. If the earbuds failed to reconnect or the Bluetooth is disconnected, they will enter pairing mode automatically.
- Search for “Bol tune SoundLiberty 034” or “Bol tune SoundLiberty 034R” on your Bluetooth list and connect.
Binaural Connection
The L/R earbuds are connected to each other by default. In case you need to connect them again, follow the following steps Take out the earbuds from the case, double tap the MFB button separately until the indicator flashes white & green, and they enter the binaural connecting status.
Clearing Pairing History
Take out the earbuds from the case and keep one in the charging case, tap and
hold the MFB button for 8s separately, the pairing
history will be cleared.
Operating Commands
Music
Calling
FAQs
- Make sure that the charging port of the charging case is properly connected to a power source.
No sound can be heard from the earbuds
- Make sure the volume level of the earbuds is appropriate.
- Make sure the headset is properly connected to the phone.
- Make sure the earbuds are within normal operating range.
Earbuds calling don’t work well
- Make sure the phone is in a strong signal area.
- The effective use distance of the earbuds is 10 meters.
- Please confirm that the earbuds are within the effective range and that there is no obstacle between the earbuds and the phone.
The operation commands are not working during playing music
- This function requires that the device paired with the earbuds supports the AVRCP (Audio/Video Remote Control Profile) protocol
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
WEEE Compliance
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in countries with separate collection systems) This marking on the product, accessories, or literature indicates that the product and its electronic accessories should not be disposed of with other household waste at the end of their working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take these items for environmentally safe recycling. Business users should contact their suppliers and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal.
- E-mail support@boltune.com
- MANUFACTURER Manufacturer: Shenzhen Danya Technology Co., Ltd.
- Address: Room 3323, Building C, GalaxyWorld Phase II, Minle Community,
- Minzhi Street, Longhua District, Shenzhen, China