Electrolux ECS Serise Range Hook User Manual
- June 2, 2024
- Electrolux
Table of Contents
Electrolux ECS Serise Range Hook User Manual
1. Product Description
Stir-fry instant suction function: When stir-frying, enable this function to increase suction instantly, and create a new “clean” kitchen in 1 minute. Side-draft technology: Peripheral smoke deflecting technology to lock fume, double-sided intake turbine to achieve complete suction, multiple oil-smoke separation systems to purify the kitchen from outside to inside. Long oil cup: Less frequent cleaning, and longer service life. Removable panel: More thorough cleaning, and easier repair and maintenance. Delay management: Continue to suck for 5 minutes in the unattended state, and automatically turn off after completion, so as to easily remove residual fume without worries.
2. Precautions
(1) Child Safety
- Do not allow children to extend their fingers or other parts of the body into the range hood. Warning: Destroy or recycle the appliance’s carton, plastic bags, and any other exterior wrapping material immediately after the product is unpacked. Children should never play with these items. Danger of suffocation!
- Precautions for Use
- Always use a power supply compliant with the requirements of the appliance. A three-pin power socket must be reliably grounded.
- The wall on which the range hood will be installed should be strong enough to bear the dead weight of the range hood itself. The wall must be noncombustible.
- Do not expose the range hood to fire directly.
- Protect the motor, switches and other electrical parts against water.
- Do not change the specifications of electrical parts, change the internal circuit, or connect other lines.
- Do not scratch, knot, or squeeze the power cable.
- If any abnormal conditions occur during use, refer to the troubleshooting section for solutions before contacting the customer service centre. If the fault persists, unplug the power plug of the range hood and contact our customer service centre.
- If the light is damaged, replace it with a new one with the same specifications.
- This appliance is for household use only instead of unintended purposes.
- Vhen oil residue stored in the oil cup reaches two thirds of its capacity, clean immediately to prevent spillage.
- Do not dismantle and repair the appliance without authorization. Otherwise, serious consequences may be followed.
- 1f users do not clean the range hood according to the instructions, there is a risk of fire.
- The room must be well-ventilated when the range hood is used in a place where gas or other fuel is combusted (but the range hood should not be installed in a place with large convection. Otherwise, the suction perforrnance will be degraded).
- The gas discharged from the range hood cannot be discharged into the waste smoke tube of burning gas or other fuels.
3. Packing List
Please check the items in the package against the packing list. If there is
any missing or lost item:
- Please ask the vendor to handle this if it is the responsibility of the company or vendor.
- Please contact the vendor or the company if it is your responsibility.
S/N| || Name| (| Qty| | S/N| | Name| | Qty
---|---|---|---|---|---|---|---|---|---|---
1| (| Appliance| (| 1set| | 8| | Airoutletcover| | 1pcs
2| I| Usermanual| I| 1pcs| || 9| || Aluminiumfoiltube| || 1pcs
3| I| Warrantycard| I| 1pcs| || 10| || Smoketubeadapter| || 1pcs
TECHNICAL SPECIFICATIONS
Power supply (W)| 220 V-240 V-/50 Hz| | 220 V-240 V-/50 Hz| |220V-240V-/50 Hz|
220V-240 V-/60 Hz|
---|---|---|---|---|---
Rated total input power (W)| 325| | 245| 335| 365
Motor input power (W) || 271| || 238| | 328| 358
Schematic Circuit Diagram
6. Installation Instructions
I. Installation Requirements
-
The wall on which the appliance is installed should be strong enough to bear the dead weight of the appliance.
-
The range hood must not be in contact with the electrical lines inside and outside the wall. Otherwise, there is a risk of electric shock.
-
The range hood should not be installed in a place with large convection. Otherwise, the suction performance will be degraded.
-
The range hood should be securely installed on the wall 650 mm above the cooker.
-
The distance between the air outlet of the range hood and the upper exhaust hole should be less than or equal to 1.5 m. so as to avoid degraded suction performance because of too long air outlet or too many turns (generally one tum).
-
The following figure shows the installation dimension of the air outlet when it is mounted to the cupboard or ceiling.
II. Installation Method -
The distance from the bottom of the range hood to the cookware supporting surface on the stove shouldbe at 650mm.lf the installation instructions of gas Stove Specify a greater distance. it should be considered. Please select an appropriate height according to the condition and the suggestions of the installer.
-
Installation of ECS9610K/ECS9612K: Identify the hole location, drill two holes with a diameter of 10 mm. a depth of 53 mm and a spacing of 180 mm on the wall, and bury the expansion pipes in the holes. Secure the mounting plate to the wall with two e5 x 53 mm wood screws. II. Installation of ECS9979K: Drill 4 holes in the wall with an impact drill, and their sizes are displayed in the installation diagram. Then bury 4 plastic expansion pipes with a diameter of 10 mm. and fix the mounting plate in the position with the size shown in the diagram. (Note: Avoid electric wires inside the wall while drilling. Otherwise, there is a risk of electric shock.)
-
To install a decorative cover, determine the position of the mounting hole of the decorative cover mounting plate according to the installation diagram. Drill two holes with a diameter of 10 mm and a depth of 50 mm with an electric impact drill at the corresponding positions, bury plastic expansion pipes, and fix the upper decorative cover bracket on the wall with two screws (05 x 53). (Note: Avoid electric wires inside the wall while drilling. Otherwise, there is a risk of electric shock.)
-
Hang the main body on the appliance mounting plate, and check that the main body is firmly hung and level. No skew is allowed.
-
After the main body is well installed, determine the drilling position of the impact drill as shown in the installation diagram. firmly bury the expansion pipes and fix the safety block. Screw in ST5X19 screws (to prevent accidental decoupling of the machine body due to external force).
-
First, remove the eight ST4X16 screws at the air outlet, put the rubber gaskets in order, and align all the holes with the mounting holes on the top plate of the case.
-
Align the eight holes of the air outlet holder with the mounting holes on the rubber sealing ring. Please note that the direction of the air outlet, should be tilted towards the electric box. Drive eight ST4X16 self-tapping screws to fix the air outlet.
-
Then wrap the air duct with the rotating clamp of the air outlet. and pay attention to the direction in which you wrap the duct. Then insert the air outlet pipe into the bottom of the circular groove of the air outlet holder (pay attention to the direction). Finally insert the four damping feet of the damp into the four clamping grooves of the air outlet, and press the clamp down with strength to ensure that the clamping feet of the clamp are well inserted.
-
Pull out the upper decorative cover, adjust the height of the upper decorative cover and hook it to the mounting hole. Align the holes on both sides of the upper decorative cover with the anchor holes of the bracket. and secure them with two stainless steel screws (M4 x 12) with gaskets. (Note: Be careful while pulling out the upper cover and pay attention to sharp edges around the product to avoid cuts.)
-
Take the other end of the air outlet pipe out of the room, and check that the pipe wall is not bulging or flat and can bend freely. Connect the power supply, start the motor, and check whether the two metal pieces turn up. The two metal pieces should fall back naturally when the appliance is turned off.
-
Direct connection is possible when the aperture of the smoke outlet on the kitchen wall is larger than the outer diameter of the exhaust pipe. Otherwise, cut off the excess part of the exhaust pipe connector smaller than the smoke outlet as required, connect the exhaust pipe and exhaust pipe connector with adhesive tape, and install it into the smoke outlet. Seal the connector with sealant.
-
If you connect the exhaust pipe directly to the outside, extend the exhaust pipe at least 30 mm out of the wall, with the air outlet slightly tilting down to avoid backflow of rainwater.
-
Align the hanging lugs at both ends of the oil cup with the slots on the two oil cup brackets at the lower end of the rear of the range hood, push the oil cup horizontally inward, and check that the oil cup is securely Installed.
-
Insert the power plug of the appliance into a power socket that is reliably grounded, and try to run the appliance to confirm whether the functions are normal.
Note: The diameter of the exhaust wall hole should be similar to that of the air outlet pipe, and should not be too small. Otherwise, it will lead to poor smoke exhaust, increased 0 noise, reduced air volume, etc.
III. Installation Checks The user should first check whether the range hoop is well installed.
IV. Power Settings After checking that the appliance is properly installed, plug the power plug of the appliance into a power socket that is reliably grounded.
7. Instructions for Use
1. The instructions for use of the Power button of ECS9610K:
Power
When you tap the “Power” button, the buzzer sounds and all buttons are lit up
in white. The red LED indicator lights turn on from left to right for 0.1
seconds. In the final 0.6 seconds, if there is a speed setting memory, the fan
is turned on in the memorized speed setting. Otherwise, the fan is turned on
in speed 2, and the red power indicator light and red indicator lights for the
corresponding speed setting and lower speed setting are turned on. Open the
flap and enter the on state. With power on, when you tap the “Power button,
the buzzer sounds, all the buttons are turned off, and the appliance is turned
off (The light is not affected). The air inlet flap is closed (the flap will
not be closed when the light is on; otherwise, it will be closed).
Fan Speed Settings
With power on, you can tap the ‘1″. ‘2″ or *3″ button to set the fan speed
with a beep sound. The indicator light for the fan speed button you tap and
the indicator lights with lower speed setting are displayed in red. You can
switch fan speed freely among ‘1″. ‘2″ and ‘3″ by tapping the fan speed key.
Stir-fry’s With power on, when you tap the ‘Stir-fry” button, the buzzer
sounds, and the red indicator lights for the fan speed and the button will be
displayed. The fan will return to the original speed setting after the speed
Setting in stir-fry mode runs for 1 minute. When you tap the “Stir-fry” button
again within 1 minute. the fan will restore its original speed setting with a
beep sound. Directly press other speed setting buttons to enter the
corresponding speed setting.
Light
-.0.- In standby/on state when you tap the “Light” button, the buzzer sounds, the Light button is lit up, the corresponding red indicator light is lit up. and the light turns on. You can tap the “Light” button again to turn off the indicator light and the light.
Delay Shutdown
Q With fan on, when you tap the “Delay” button, the buzzer sounds, the red
indicator light for the Delay button blinks, and the system starts to execute
the “Delay Shutdown” function. The fan runs in speed
setting 1 and the red indicator right for speed setting 1 turns on. The
appliance shuts down after 5 minutes. You can tap the “Delay button again in
“Delay Shutdown” mode to disable the delay shutdown function. Upon completion
of delay shutdown, the appliance is shut down and the light turns off.
Strainer Clean is After the appliance is powered on for the first time, the
system will accumulate the operation time of the appliance. When the operation
time reaches 50 hours, the red indicator light for the Clean button will
blink. Users needs to remove the strainer for cleaning. Press and hold the
‘Strainer Clean” button for 3 seconds after the strainer is reinstalled to
clear the alarm (The 50-hour timer starts again).
Flap When there is lighting or the fan is on, turn off the hood to open the
air inlet flap, otherwise close the air inlet flap.
2. The instructions for use of the Power button of ECS9612K:
; Q. 0 yet I 2 3 4 3 ce 0 ; 5
Power When you tap the “Power” button or wave your hand right, the buzzer
sounds and all white button indicator lights are lit up. The red LED indicator
lights turn on from left to right for 0.1 seconds. In the last 0.6 seconds, if
there is a speed setting memory, the fan is turned on in the memorized speed
setting. Otherwise, the fan is turned on in speed 2. and the red power
indicator light, the red indicator light for the corresponding speed setting,
and the ventilation indicator light are turned on. The appliance is powered
on. With power on. when you tap the “Power button, the buzzer sounds, all the
buttons are turned off, and the appliance is turned off (The light is not
affected). The air inlet flap is closed (the flap will not be closed when the
light is on; otherwise, it will be closed).
Fan Speed Settings With power on. you can tap the “1”. “2”. “3”. “4”, or “5”
button or wave your hand left or right to set the fan speed with a beep sound.
The indicator light for the fan speed button you tap, the ventilation
indicator light, and the indicator lights with lower speed setting are
displayed in red. You can switch fan speed freely among “1’, “2”, “3”, “4”,
and “5” by tapping the fan speed key.
Stir-fry ‘t With power on. when you tap the “Stir-fry” button, all the speed
settings are displayed. The fan will return to the original speed setting
after the speed setting in stir-fry mode runs for 1 minute. When you tap the
“Stir-fry” button again within 1 minute, the fan will restore its original
speed setting with a beep sound.
Ventilation Y+ With power on, when you tap the “Vent” button, the ventilation
function is enabled, and the red indicator light for the button blinks. The
fan runs for 5 minutes in speed setting 1 every one hour. You can tap the
“Vent” button again or swipe right to cancel ventilation. The fan starts in
speed setting 2. You can tap the “Power button or swipe left to shut down the
appliance.
Light 4’ In standby/on state, when you tap the “Light” button, the buzzer
sounds, the Light button is lit up. the corresponding red indicator light is
lit up, and the light turns on. You can tap the “Light” button again to turn
off the indicator light and the light.
Delay nQ With fan on, when you tap the ‘Delay’ button or control the appliance
with gesture. that is, swiping left in speed sauna 1. the buzzer sounds, the
red indicator light for the Delay button Clinks and the red indicator light
for speed setting I hens co. and the system sans to execute the Shutdown’
function. The fan runs in speed setting 1 and Steel after 5 minutes. You can
tap the “Delay’ button again in ‘Delay Shutdown’ mode to disable the delay
shutdown function. Upon completion of delay shutdown. the appliance Is shut
down and the light turns off. Strainer Clean
• After the appliance is powered on for the first time. the system will
accumulate the operation time of the appliance. When the operation time
reaches 50 hobos. the red indicator ight for the Clean button vas Mink. Users
needs to remove the strainer for cleaning. Press and tcld the ‘Strainer Clean’
button for 3 seconds after the strainer is reinstated to clear the alarm (The
50-hour timer starts again)
Flap When there is lighten or the tan is CO, ttaw on the hood to open the air
inter flap. othenwse close the air Inlet flap.
Gesture Settings With power ca, press and hold the ‘Power button for 3 seconds
to enter the gesture setting mode. Tap the ‘I’ button. The red indicator tight
turns on and the gesture function is enabled. Tap the button. The red
indicator Lehi turns on and the gesture function is disabled. In gesture
setting mode. if you lap the ‘Power button or light’ button, or the apptance a
inactive for 3 seconds. the appliance Is turned off and the gesture function
is set (The gesture function enabled by default).
Gesture Function When the appliance is turned oft, if you wave your hand left.
me appliance remains off without response. You Can wave your hand right to
start the applianCe. The applianCe starts in speed selling 2 for the Fest
time. The appliance will starts in the last speed sarong in later uses (not
ventlabon or delay mode). When the appliance is operating, you can wave your
hand left to reduce speed setting from stir fry. 5, 4, 3, 2, 1, delay shutdown
to shutdown, or wave your hand right to increase speed selling from 1, 2, 3,
4. 5 to sbr fry, and then maintain at the stir fry mode without other
response. When the delay shutdown function is enabled. you can wave your hand
left to she down the appliance, or wave your hand right to start the appliance
in speed setting 2. When the ventilation function is enabled, you can wave
your hand left to shut down the appliance, or wave your hand right to start
the appliance ci speed setting 2. In gesture setting mode, the appliance does
not respond when you wave your hand ft or nght. The in truaicos for use of We
Power button 01 ECS997914′
Power a) When you tap the ‘Power’ button or wave your hand right. the buzzer sounds and all white button indicator lights are lit up. The red LED indicator lights turn on from lea to right for 0.1 seconds. In the Iasi 0.6 seconds, If there is a speed setting memory, the fan is turned on in the memorwed speed setting.
Otherwise. the fan is turned on in speed 2. and the red power indicator light,
the red indicator lights for the corresponding speed setting and lower speed
settings, and the ventilation indicator light are turned on. Open the lifting
panel and enter the on state. With power on, when you tap the “Power button,
the buzzer sounds, and all the button lights and indicator lights are turned
off (The light Is not affected). The clock is steadily on and the appliance is
turned off. The lifting panel is closed.
Fan Speed Settings
With power on, you can tap the “1”, “2”. “3”. “4”. or ‘5″ button or wave your
hand left or right to set the fan speed with a beep sound. The indicator light
for the fan speed button you tap, the ventilation indicator light, and the
indicator lights with lower speed setting are displayed in red. You can switch
(an speed freely among “1”, “2′, “3”, “4’, and “5” by tapping the fan speed
key or using gestures.
Stir-fry
With power on, when you tap the “Stir-fry” button, the buzzer sounds, and all
the speed settings are displayed. TM fan will return to the original speed
setting after the speed setting in stir-fry mode runs for 1 minute. When you
tap the “Stir-fry” button again within 1 minute. the fan will restore Its
original speed setting with a beep sound. If you wave your hand right within 1
minute. the appliance will not respond, and if you wave your hand left, speed
setting 5 is enabled. Stir-fry for 1 minute. and the clock should display
countdown (only for an appliance with clock function). Directly press other
speed setting buttons to enter the corresponding speed setting.
Ventilation
vtge With power on, when you tap the ‘Vent” button, the ventilation function
is enabled, and the red indicator light for the button blinks. The fan runs
for 5 minutes in speed setting 1 every one hour. The screen displays a
5-minute countdown, and the dock is displayed for the other 55 minutes after
the countdown. You can press and hold the “Vent” button again for 3 minutes or
swipe right to cancel ventilation. The fan starts in speed setting 2. You can
tap the “Power button or swipe left to shut down the appliance.
Lights
In standby/on state, when you tap the ‘Light” button, the buzzer sounds, the
Light button is lit up. the corresponding red indicator light is lit up, and
the light turns on (high illumination). You can tap the light’ button again to
switch from high illumination to low illumination, repeat the operation to
turn off the indicator light and the light, and repeal the operation again to
enable high illumination, and so on and so forth.
Delay Shutdown
Q With fan on, when you tap the ‘Delay button or control the appliance with
gestures, that is, swiping left in speed setting 1. the buzzer sounds, the red
Indicator light for the Delay button blinks , the system starts to execute the
“Delay Shutdown” function. The tan runs in speed setting 1, the red indicator
light for speed setting 1 turns on. and the screen starts to count down (by
default, the countdown starts from 5 minutes). You can tap the “Delay’ button
again to change the time from 5 minutes to 10 minutes, repeat the operation to
change the time from 10 minutes to 15 minutes, and repeat the operation again
to disable the delay shutdown function and restore speed setting 2. When the
delay function Is on, press and hold the delay button for 3 seconds or wave
your hand to the right to exit the delay and restore speed setting 2 directly.
Press the power button or wave your hand left to turn off the appliance. Upon
completion of delay shutdown, the appliance is shut down and the light turns
off.
Strainer Clean
After the appliance is powered on for the first time. the system will
accumulate the operation time of the appliance. When the operation time
reaches 50 hours, the red indicator light for the Clean button will blink.
Users needs to remove the strainer for cleaning. Press and hold the “Strainer
Clean’ button for 3 seconds after the strainer is reinstalled to clear the
alarm (The 50-hour timer starts again).
Lifting
When there is lighting or the fan is on, open the lifting panel, otherwise
close the lifting panel.
Clock setting
With power off, press and hold the ‘Power” button and “Light’ button for 3
seconds to enter the clock setting mode. The clock flashes, the “V, ‘2”. ‘3’,
“4”. ‘5’ buttons and the red indicator lights are lit up. Press and hold ‘1″
and “2” to change the hour. ‘1″ to decrease the value. ‘2’ to increase the
value. and the input range is 1-12. Press and hold “1” and ‘2″ to continuously
change the number. Press and hold “3” and “4’ to change the minute. ‘3’ to
decrease the value. “4” to increase the value, and the input range is 0-59.
Press and hold “3” and “4′ to continuously change the number. Press “5′ to
switch between AM and PM. In the clock setting mode, tap the ‘Power button or
tight’ button or the appliance is inactive for 3 seconds, the appliance is
turned off.
Gesture Settings
With power off, press and hold the “Power button for 3 seconds to enter the
gesture setting mode, and the “1” and “2” buttons are lit up. All shipped
appliances feature the gesture function by default. The red indicator for the
‘1″ button is lit up. and the function screen displays “on”. When you tap the
‘2″ button, the red indicator for the “2’ button is lit up. and the red
indicator for the “1” button is turned off. At this time, the gesture function
is turned off and the screen displays ‘off. In gesture setting mode, if you
tap the “Power button or “Light” button, or the appliance is inactive for 3
seconds, the appliance is turned off and the gesture function is set.
Gesture Function
When the appliance is turned off, if you wave your hand left, the appliance
remains off without response. You can wave your hand right to start the
appliance. The appliance starts in speed setting 2 for the first time. The
appliance will starts in the last speed setting in later uses (not ventilation
or delay mode). When the appliance is operating. you can wave your hand left
to reduce speed setting from stir fry. 5. 4, 3. 2. 1. delay shutdown to
shutdown. or wave your hand right to increase speed setting from 1. 2. 3. 4. 5
to stir fry, and then maintain at the stir fry mode without other response.
When the ‘Delay Shutdown’ function is enabled, you can wave your hand left to
shut down the appliance. or wave your hand right to start the appliance in
speed setting 2. When the ventilation function is enabled, you can wave your
hand left to shut down the appliance, or wave your hand right to start the
appliance in speed setting 2. (In clock setting mode, the appliance does not
respond when you wave your hand left or right. In gesture setting mode, the
appliance does not respond when you wave your hand left or right.)
1. Extend a small slotted screwdriver or similar
2. Pry up the light from the hood and disconnect objects into the gap between
the light cover and the connector. The right can be replaced. the hood.
Removal of the switch: (1) Removal of ECS9979K switch: (2) ECS9612K Removal of
ECS9610K switch:
Unscrew the 3 screws on the top of the back of the glass fiber reinforced
plastic panel, directly remove the glass panel. Then remove the switch platen.
unscrew the screws on both sides of the switch, and replace the switch.
Unscrew the 2 big flat head screws behind the glass with a screwdriver, then
press and hold the glass panel to push downward, and then remove the glass.
Then unscrew the three screws securing the switch to remove the switch.
8. Maintenance
Maintenance guarantees good performance. Please take good care of your
appliance. Be sure to cut off the power supply before any maintenance
operations (hold the plug and remove it). Perform maintenance operations with
gloves to prevent cuts by sharp edges of the appliance. Remove oil stains on
the surface of the strainer and mainframe regularly, and keep the appliance
clean. Clean the strainer every month to ensure good suction and exhaust
performance. Perform total preventive maintenance every year to dean oil
stains and guarantee good performance. Do not dean the appliance with water or
flammable cleaning agent. Maintenance ECS9612K7 ECS9610K: Removal of Parts
Handle with care while disassembling parts to avoid distortion or damage.
- Press the lighting button to fully open the flap glass, and then unplug the power plug.
- Unscrew the 5 screws under the glass with a screwdriver and remove the lower glass to clean the inside.
- Remove the screws securing the strainer and remove the inner strainer.
- Remove the screws securing the case cover and remove the case cover.
- Remove the screws securing the guide ring and remove the guide ring.
- Remove the wind wheel cap in the direction as indicated by the arrow and remove the wind wheel.
- After maintenance operations, reinstall parts in the reverse order of removal.
Cleaning of Parts
- Please use neutral detergent, soft cloth and soft brush for cleaning parts. Do not use organic solvents.
- Please soak parts for 30 minutes before cleaning. Avoid deformation or damage during cleaning.
- Upon completion of part cleaning. rinse parts with fresh water and wipe dry with a soft cloth.
- Use a soft dry cloth or soft brush to clean the electrical parts, instead of water or detergent.
- If users do not dean the appliance according to the instructions. there may be a risk of fire.
- Maintenance of ECS9979K:
Press the panel’s lifting button to lift the glass panel to the top, remove the strainer assembly. Separate the inner and outer strainers, soak them in warm water with neutral detergent, and clean them with a brush. Dry the cleaned strainers in the air or wipe them dry, and install them in turn to ensure that the grease filters are well installed to prevent any scratch when the glass panel slides. Dry the oil cup in the air or wipe it dry, hold both ends of the oil cup and align them with the two buckles at the lower end of the hood to install it. Make sure the oil cup is well installed. Please clean the oil cup regularly to avoid any smelly or solidified oil due to a long storage time.
Removal of air duct:
Handle with care while disassembling parts to avoid distortion or damage.
- Unscrew the screws securing the external decorative cover and remove the external decorative cover.
- Remove the screws securing the case cover and remove the case cover.
- Remove the screws securing the guide ring and remove the guide ring.
- Remove the wind wheel cap in the direction as indicated by the arrow and remove the wind wheel.
- After maintenance operations, reinstall parts in the reverse order of removal. it.
Cleaning of Parts
- Please use neutral detergent, soft cloth and soft brush for cleaning parts. Do not use organic solvents.
- Please soak parts for 30 minutes before cleaning. Avoid deformation or damage during cleaning.
- Upon completion of part cleaning, rinse parts with fresh water and wipe dry with a soft cloth.
- Use a soft dry cloth or soft brush to dean the electrical parts, instead of water or detergent.
- If users do not clean the appliance according to the instructions, there may be a risk of fire.
Note: The range hood should be maintained by skilled personnel.
ThailandConsumer Care Tel : (+66 2) 725 9000 Electrolux Thailand Co.,
Ltd.Electrolux Building 14th Floor 1910 New Phetchaburi Road,Bangkapi, Huai
Khwang, Bangkok 10310 Office Tel : (+66 2) 7259100Office Fax : (+66 2)
7259299Email :
customercarethai@electrolux.com|
SingaporeConsumer Care Center Tel: (+65) 6727 3699 Electrolux S.E.A. Pte
Ltd.351 Braddell Road#01-04, 351 On BraddellSingapore 579713Email : customer-
care.sin@eIectroIux.com|
---|---|---
IndonesiaHotline service: 08041119999 PT. Electrolux Indonesia Electrolux
BuildingJI.Abdul Muis No.34, Petojo Selatan, Gambir Jakarta Pusat 10160
Email:customercare@eIectrolux.co.id
SMS & WA : 0812.8088.8863| PhilippinesConsumer Care Center Toll
Free:1-800-10-845-CARE(2273)Consumer Care Hotline:(+63 2)845-CARE(2273)
Electrolux Philippines,lnc.Unit B 12F Cyber Sigma Bldg, Lawton Avenue,
McKinley West,Taguig, Philippines 1634 TrunkIine:+63 2 737-4757
Website:www.eIectrolux.com.phEmail:wecare@electroIux.com|
VietnamConsumer Care Center Toll Free 1800-58-88-99Tel: (+84 28)
39105465Electrolux Vietnam Ltd.Unit 1&2, 10F Sofic Tower, #10 Mai Chi Tho
Street,Thu Thiem Ward, Thu Due City, Ho Chi Minh City, Vietnam|
MalaysiaConsumer Care Center Tel: 1300-88-11-22 Electrolux Home Appliances
Sdn. Bhd.Corporate Office Address: Unit T2-7, 7th Floor, Tower 2, PJ33, No. 3,
Jalan Semangat, Seksyen 13, 46200 Petaling Jaya, Selangor.Office Tel : (+60 3)
7843 5999Office Fax : (+60 3) 7955 5511|
| Consumer Care Center Address: Lot C6, No. 28,|
Jalan 15/22, Taman Perindustrian Tiong Nam, 40200 Shah Alam, SelangorConsumer
Care Center Fax : (+60 3) 5524 2521 Email :
malaysia.customercare@eIectroIux.com|
HONG KONGSERVICE HOTLINE: (+852) 3193 9888DCH ELECTRICAL APPLIANCES SERVICE
CENTRE|
4/F, DCH BUILDING, 20 KAI CHEUNG| |
ROAD,| |
KOWLOON BAY, HONG KONG| |
EMAIL: customercare@dch.com.hk| |
WEBSITE: www.electrolux.com.hk| |
www.electrolux.com
The Thoughtful Design Innovator.
Do you remember the last time you opened a gift that made you say. ‘Oh! How
did you know? That’s exactly what I wanted?’ That’s the kind of feeling that
we at Electrolux seek to evoke in everyone who chooses or uses one of our
products. We devote time. knowledge, and a great deal of thought to
anticipating and creating the kind of appliances that our customers really
need and want.
This kind of thoughtful care means innovating with insight. Not design for
design’s Sake, but design for the user’s Sake. For us, thoughtful design means
making appliances easier to use and tasks more enjoyable to perform, freeing
our customers to experience the ultimate 21st century luxury: ease of mind.
Our aim is to make this ease of mind more available to more people in more
pans of their everyday lives. all over the world. The “Thinking of you”
promise from Electrokoc goes beyond meeting the needs of today’s consumers. It
also means we’re committed to making appliances safe for the environment—now
and for future generations.
Electrolux. Thinking of you. Share more of our thinking at www.electrolux.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>