avigilon NVR5 16 GB RAM Kit Installation Guide

: June 4, 2024
: aVIGILON

Table of Contents

avigilon NVR5 16 GB RAM Kit
Introduction
Installing the NVR5 16 GB RAM Kit
Opening the Cover
Installing Additional RAM
Limited Warranty
For More Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

avigilon NVR5 16 GB RAM Kit

© 2022, Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILON are trademarks of Avigilon Corporation. Intel is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Other names or logos mentioned herein may be the trademarks of their respective owners. The absence of the symbols ™ and ® in proximity to each trademark in this document or at all is not a disclaimer of ownership of the related trademark. This document has been compiled and published using product descriptions and specifications available at the time of publication. The contents of this document and the specifications of the products discussed herein are subject to change without notice. Avigilon Corporation reserves the right to make any such changes without notice. Neither Avigilon Corporation nor any of its affiliated companies: (1) guarantees the completeness or accuracy of the information contained in this document; or (2) is responsible for your use of, or reliance on, the information. Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages) caused by reliance on the information presented herein. Avigilon Corporation avigilon.com 20220621

Introduction

Avigilon provides an optional RAM Upgrade Kit for the NVR5 Standard 16-64 TB and Premium 96-160 TB models. Up to eight 8 GB RAM DIMMs are supported per CPU in these NVR5 models. Part Number Description NVR5-RAM-16GB-A NVR5 Standard/Premium 16 GB RAM Upgrade Kit

Note: If installing NVR5 RAM Upgrade Kits in a system with two CPUs, kits must be installed in pairs (four DIMMs at a time). DIMMs must follow specific configuration rules, and must be installed in the same configuration for each of the two CPUs. See Installing Additional RAM on page 7 for more information.

Confirm Package Contents
Confirm that the kit you are installing contains the following components: l 2 × 8 GB DIMM per RAM Kit

Recommended Tools
The following tools are not included in the kit package, but are needed to complete the installation:

l Phillips #2 screwdriver
l Wrist-grounding strap connected to the ground
l ESD Mat

Important : It is recommended that you always use an antistatic mat and antistatic strap while working on components inside the system.

Installing the NVR5 16 GB RAM Kit

Note : If the NVR5 is an operating part of your security system, be aware that it must be shut down to complete this procedure.

Before starting to install the kit:

Turn off the NVR5, including all attached peripherals. Press the power button on the front panel, and wait for the light to stop blinking to indicate shutdown is complete.
WARNING — Opening or removing the system cover while the system is powered on may expose you to a risk of electric shock.
Disconnect the NVR5 from the electrical outlet and disconnect the peripherals.
Remove all network, power and peripheral cables from the NVR5.
If applicable, remove the NVR5 from the rack.

Important : Whenever you need to lift the system, get others to assist you. To avoid injury, do not attempt to lift the system by yourself

Opening the Cover

At the top of the NVR5, unlock the latch release then lift and rotate the latch towards the back of the unit. The cover slides back and is released from the body.
Tip : Use a Phillips #2 screwdriver to remove the shipping screws before unlatching the cover if you are removing the cover of an NVR5 for the first time.
Remove the air shroud by holding it at both ends and lifting it away from the system.
View the interior of the NVR5 and identify the locations where the components of the kit will be
installed. The view below shows the details of an NVR5 with all of the covers and cards removed, and important components labeled with numbers. The components affected by the NVR5 Standard/Premium RAM Upgrade Kit are:
3—Memory modules The installed DIMMs are located here.

Installing Additional RAM

Important : To prevent damage to the DIMM or memory module socket during installation:

Do not bend or flex the DIMM.
Handle each DIMM only by the edges to ensure that you don’t touch the middle of the memory module or the metallic contacts.
When installing a DIMM, apply pressure to both ends of the memory module evenly. Do not apply pressure to the middle.

Follow the guidelines below based on the appropriate CPU configuration:
If upgrading a single-CPU configuration with one RAM Upgrade Kit, install DIMMs into the memory module sockets of CPU 1 following the sequence: A1, A2, A3, A4, A5, A6, A7, A8. For example, on a single-CPU NVR5 Standard with A1 and A2 populated by default, install the pair of DIMMs into sockets A3 and A4.
If upgrading a dual-CPU configuration with two RAM Upgrade kits, install the first kit following the single-CPU steps listed above. Then, install the second kit into the memory module sockets of CPU 2 following the sequence: B1, B2, B3, B4, B5, B6, B7, B8. Ensure that the populated sockets in CPU 2 match those in CPU 1.
Note : Install both DIMMs provided in each kit and only in these configurations. Configurations not following this sequence are not supported and may result in non-optimal memory performance or other unexpected behavior
Open the ejector clips on each side of the empty memory module sockets outward to allow the DIMMs to be inserted into the sockets.
Align the edge connector of the DIMMs with the alignment key of the sockets and press the DIMMs into the sockets until the socket levers click into place.

Reattaching the Cover
When all the components of the kit have been installed:

Reinstall the top of the cooling shroud:
Align the slot on the air shroud with the standoff in the system.
Lower the air shroud into the system until it is firmly seated.
Close and lock the NVR5 cover.
If the NVR5 was rack mounted and removed to install the kit, remount it into the rack.
Reconnect all the peripherals and cables
Important : Ensure that both of the power supplies are connected to main power. The upgraded NVR5 requires both power supplies to properly function.
Power on the NVR5.

Confirming the Installation
Verify the upgrade is successful

Log in to the ACC Client on a workstation on the same network as the NVR5.
In the System Explorer, click Site Setup, and click Site to expand the site containing the upgraded NVR5.
Click to select the upgraded NVR5.
Verify that the NVR5 has the correct amount of memory installed:
In the System Explorer, select the upgraded NVR5 server.
In the New Task menu , click Site Health.
Under the General Information heading, the sum of Memory usage and System Available Memory should have increased by 16 GB for each RAM Upgrade Kit installed. For example, a single-CPU NVR5 Standard should have upgraded from 16 GB to 32 GB (~32,000 MB) after installing one kit.